Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2111    Throttle Actuator Control System - Stuck Open

DTC    P2112    Throttle Actuator Control System - Stuck Closed

for Preparation Click here


DESCRIPTION

The throttle motor is operated by the ECM and it opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body. The throttle position sensor provides ECM with feedback to control the throttle motor and set the throttle valve angle in response to driver input.

HINT:
This Electrical Throttle Control System (ETCS) does not use a throttle cable.


DTC No.
DTC Detection Condition
Trouble Area
P2111
Throttle motor locked during ECM orders to open
  1. Throttle control motor circuit
  2. Throttle control motor
  3. Throttle body
  4. Throttle valve
P2112
Throttle motor locked during ECM orders to close
  1. Throttle control motor circuit
  2. Throttle control motor
  3. Throttle body
  4. Throttle valve

MONITOR DESCRIPTION

The ECM concludes that there is a malfunction of the ETCS when the throttle valve remains at a fixed angle despite high drive current supplying from the ECM. The ECM will turn on the MIL and a DTC is set.

FAIL-SAFE

If the Electronic Throttle Control System (ETCS) has a malfunction, the ECM cuts off current to the throttle control motor. The throttle control valve returns to a predetermined opening angle (approximately 16°) by the force of the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal opening angle to enable the vehicle to continue to drive.
If the accelerator pedal is depressed firmly and slowly, the vehicle can be driven slowly.
If a "pass" condition is detected and then the power switch is turned OFF, the fail-safe operation will stop and the system will return to normal condition.

MONITOR DESCRIPTION


Related DTCs
P2111: Throttle motor actuator lock (open)
P2112: Throttle motor actuator lock (closed)
Main sensors/components
Throttle actuator motor
Frequency of operation
Continuous
Duration
0.5 seconds
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


P2111: 
The monitor will run whenever the following DTCs are not present
None
All of the following conditions are met
-
System guard*
ON
Throttle motor current
2 A or more
Duty cycle to close throttle
80% or more
* System guard is ON when the following conditions are met
-
Throttle actuator
ON
Throttle actuator duty calculation
Executing
Throttle position sensor
Fail determined
Throttle actuator current-cut operation
Not executing
Throttle actuator power supply
4 V or more
Throttle actuator
Fail determined

P2112: 
The monitor will run whenever the following DTCs are not present
None
All of the following conditions are met
-
System guard*
ON
Throttle motor current
2 A or more
Duty cycle to open throttle
80% or more
* System guard is ON when the following conditions are met
-
Throttle actuator
ON
Throttle actuator duty calculation
Executing
Throttle position sensor
Fail determined
Throttle actuator current-cut operation
Not executing
Throttle actuator power supply
4 V or more
Throttle actuator
Fail determined

TYPICAL MALFUNCTION THRESHOLDS


P2111: 
TP sensor voltage change
No change

P2112: 
TP sensor voltage change
No change

WIRING DIAGRAM

Refer to DTC P2102 .

INSPECTION PROCEDURE

Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2111 AND/OR P2112)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    P2111 or P2112
    A
    P2111 or P2112, and other DTCs
    B

    HINT:
    If any other codes besides P2111 and/or P2112 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.INSPECT THROTTLE W/ MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
  1. Check for contamination between the throttle valve and the housing. If necessary, clean the throttle body. And check that the throttle valve moves smoothly.



NG
REPLACE THROTTLE W/ MOTOR BODY ASSEMBLY
OK


3.CHECK IF DTC OUTPUT RECURS (DTC P2111 AND/OR P2112)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn the tester ON.

  1. Clear the DTCs.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine, and depress and release the accelerator pedal quickly (fully open and fully close).

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Start the engine, and depress and release the accelerator pedal quickly (fully open and fully close).

  1. Read DTCs.

    Result:
    Display (DTC output)
    Proceed to
    No output
    A
    P2111 and/or P2112
    B



B
REPLACE ECM
A

CHECK FOR INTERMITTENT PROBLEMS