Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2119    Throttle Actuator Control Throttle Body Range / Performance

for Preparation Click here


DESCRIPTION

The Electric Throttle Control System (ETCS) is composed of a throttle motor that operates the throttle valve, a throttle position sensor that detects the opening angle of the throttle valve, an accelerator pedal position sensor that detects the accelerator pedal position, and the ECM that controls the ETCS system.
The ECM operates the throttle motor to position the throttle valve for proper response to driver inputs. The throttle position sensor, mounted on the throttle body, provides this signal to the ECM so that the ECM can regulate the throttle motor.

DTC No.
DTC Detection Condition
Trouble Area
P2119
Throttle opening angle continues to vary greatly from its target angle
  1. Electric throttle control system
  2. ECM

MONITOR DESCRIPTION

The ECM determines the "actual" throttle valve angle based on the throttle position sensor signal. The "actual" throttle valve position is compared to the "target" throttle valve position commanded by the ECM. If the difference of these two values exceeds a specified limit, the ECM interprets this as a fault in the ETCS system. The ECM turns on the MIL and a DTC is set.

FAIL-SAFE

If the Electronic Throttle Control System (ETCS) has a malfunction, the ECM cuts off current to the throttle control motor. The throttle control valve returns to a predetermined opening angle (approximately 16°) by the force of the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal opening angle to enable the vehicle to continue to drive.
If the accelerator pedal is depressed firmly and slowly, the vehicle can be driven slowly.
If a "pass" condition is detected and then the power switch is turned OFF, the fail-safe operation will stop and the system will return to normal condition.

MONITOR STRATEGY


Related DTCs
P2119: Electronic throttle control system failure
Required sensors/components
Main:
Throttle actuator motor
Related:
Throttle position sensor
Frequency of operation
Continuous
Duration
Within 1 second
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
None
System guard*
ON
*System guard is ON when the following conditions are met
-
Throttle actuator
ON
Throttle actuator duty calculation
Executing
Throttle position sensor
Fail determined
Throttle actuator current-cut operation
Not executing
Throttle actuator power supply
4 V or more
Throttle actuator
Fail determined

TYPICAL MALFUNCTION THRESHOLDS


Either of the following conditions A or B is met
-
A. Commanded closed throttle position - current closed throttle position
0.3 V or more
B. Commanded open throttle position - current open throttle position
0.3 V or more

COMPONENT OPERATING RANGE


Commanded throttle valve position
Same as current throttle valve position

WIRING DIAGRAM

Refer to DTC P2102 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2119)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P2119
    A
    P2119 and other DTCs
    B

    HINT:
    If any other codes besides P2119 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.CHECK IF DTC OUTPUT RECURS
  1. Clear the DTCs (Click here).

  1. Allow the engine to idle for 15 seconds.

  1. Securely apply the parking brake, and place the shift position in D.

  1. Depress the brake pedal securely and the accelerator pedal fully for 5 seconds.

  1. Read the DTCs.

    HINT:
    Actual throttle position (TP) sensor voltage can be confirmed using Techstream [DATA LIST / USER DATA /THROTTLE POS #1].

    OK:
    No DTC output.



OK
SYSTEM OK
NG

REPLACE THROTTLE W/ MOTOR BODY ASSEMBLY