Home › HYBRID SYSTEM › P112 HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A94-557    DC / DC Converter Performance

for Preparation Click here


DESCRIPTION

See the description of the booster converter .
If the boost converter has a circuit malfunction, internal short, or overheats, the boost converter transmits that information to the FCV terminal of the HV control ECU via the boost converter fail signal line.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A94
557
Boost converter fail (FCV) signal detection (circuit malfunction)
  1. Wire harness or connector
  2. Inverter with converter assembly

MONITOR DESCRIPTION

If the boost converter detects a circuit malfunction, it transmits a boost converter fail signal to the HV control ECU. Upon receiving this signal, the HV control ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A94 (INF 557):
FCV detection circuit malfunction
Required sensor / components
Boost converter
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Boost converter
Circuit malfunction

COMPONENT OPERATING RANGE


Boost converter
DTC P0A94 (INF 557) is not detected

WIRING DIAGRAM

Refer to DTC P0A78 (INF 282) .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ OUTPUT DTC (HV ECU)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTC listed in the table below is output


    DTC No.
    INF Code
    Detection Item
    See Page
    P0A94
    551 or 552
    DC / DC Converter Malfunction
    Click here



YES
GO TO THE PAGE NUMBER SHOWN IN THE TABLE ABOVE
NO


2.CHECK CONNECTION CONDITION OF INVERTER CONNECTOR (LOOSENESS AND POOR CONTACT)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .



    A092044E02
  1. Check the connection condition of the I9 and I10 inverter connectors.

    OK:
    Connectors have been connected securely and there is no poor connection.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
CONNECT SECURELY
OK


3.READ OUTPUT DTC (HV ECU)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    DTCs P0A78 (INF 282, 286) and P0A7A (INF 324) (inverter circuit malfunction) are output



NO
REPLACE INVERTER WITH CONVERTER ASSEMBLY
YES


4.INSPECT INVERTER WITH CONVERTER ASSEMBLY (IGCT VOLTAGE)

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip .

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause malfunction. Therefore, never turn the power switch ON (READY) in this state.

  1. Remove the inverter cover .

  1. Turn the power switch ON (IG).

    HINT:
    DTCs for the interlock switch system are output when turning the power switch ON (IG) with both service plug grip and inverter cover removed.



    A093729E02
  1. Measure the voltage between the terminals of the inverter connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    IGCT (I9-1) - GND1 (I9-2)
    8 V or more

  1. Turn the power switch OFF.

  1. Reinstall the inverter cover .

  1. Reinstall the service plug grip .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY