Home › HYBRID SYSTEM › P112 HYBRID BATTERY CONTROL › FRAME WIRE

FRAME WIRE > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 FRAME WIRE


A089187E01

CAUTION:
Wear insulating gloves.

  1. Install the No. 2 frame wire with new 26 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    A077536E02
  1. Connect the No. 2 frame wire connector to the battery ECU, then connect the clamp.

  1. Connect the temperature sensor connector to the battery ECU.



2. INSTALL NO. 2 MAIN BATTERY CABLE


A083566E02

CAUTION:
Wear insulating gloves.

  1. Temporarily install the No. 2 main battery cable to the HV battery.

  1. Install the No. 2 main battery cable to the No. 2 frame wire with a new nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Temporarily install the main battery cable and system main relay terminal, in that order, to the No. 2 system main relay, then tighten the new nut.

    Torque:
    5.6 N*m{ 57 kgf*cm , 50 in.*lbf }



    A083580E01
  1. Install the terminal cover shown in the illustration.



3. INSTALL MAIN BATTERY CABLE


A083551E01

CAUTION:
Wear insulating gloves.

  1. Temporarily install the main battery cable to the HV battery.

  1. Install the main battery cable to the No. 2 frame wire with a new nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Install the main battery cable to the No. 3 system main relay with a new nut.

    Torque:
    5.6 N*m{ 57 kgf*cm , 50 in.*lbf }

  1. Install the aluminum shield wire with a new nut.

    Torque:
    3.3 N*m{ 34 kgf*cm , 29 in.*lbf }



    A083579E01
  1. Install the terminal cover shown in the illustration.



4. INSTALL NO. 3 BATTERY CARRIER CUSHION


A077542E01

CAUTION:
Wear insulating gloves.

  1. Degrease and clean the installation surface of the battery carrier cushion.

  1. Install a new battery carrier cushion.



5. INSTALL NO. 1 WIRE HARNESS PROTECTOR COVER


A083582E02

CAUTION:
Wear insulating gloves.



6. INSTALL NO. 3 WIRE HARNESS PROTECTOR COVER

CAUTION:
Wear insulating gloves.



7. INSTALL BATTERY COVER

CAUTION:
Wear insulating gloves.

  1. Temporarily fasten the battery carrier catch bracket to the battery room ventilation hose.



  1. Install the battery cover with the 6 bolts, 2 nuts and clip.


    A083611E01

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the protector on the battery cover.



8. INSTALL HV BATTERY ASSEMBLY
  1. Install the HV battery to the vehicle (Click here).



9. INSTALL SERVICE PLUG GRIP

CAUTION:
Wear insulating gloves.

  1. Joint the service plug grip with the HV battery.

  1. While pushing the service plug grip to the right, rotate the lever to the right.

  1. Slide the lever down to lock the service plug grip in place.

    NOTICE:
    1. The service plug grip must be locked. If not, it may cause DTCs to output.

    2. Do not operate the power switch when the service plug grip is not properly locked. It may damage the hybrid vehicle control ECU in rare cases.


      A089219



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
  1. When the warning light is illuminated or the battery has been disconnected and reconnected, turning the power switch may not start the system on the first try. If so, turn the power switch again.
  2. With the power switch's power mode changed to ON (IG), disconnect the battery. If the key is not in the key slot during reconnection, DTC B2799 may be output.



    A088356E01
  1. Connect the battery negative cable, and then tighten the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



11. INSTALL REAR NO. 3 FLOOR BOARD


    A088355E02
  1. Install the floor board, and then attach the 4 claws.



12. INSTALL REAR DECK FLOOR BOX


    A088354E01
  1. Install the rear deck floor box to the vehicle.



13. INSTALL REAR NO. 2 FLOOR BOARD


    A088353E01
  1. Install the floor board, and then lock the 2 cover knobs.



14. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.