Home › ENGINE › 1NZ-FXE LUBRICATION › OIL PUMP

OIL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL OIL PUMP ASSEMBLY


A067553E01
  1. Install 2 new O-rings to the 2 locations as shown in the illustration.



  1. Apply seal packing to the engine body and oil pump as shown in the illustration below.

    Seal packing:
    Water pump part: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
    Other part: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove pump any oil from the contact surface.
    1. Install the oil pump within 3 minutes, and tighten the bolts within 15 minutes after applying seal packing.
    1. Do not expose the seal packing to engine oil within 2 hours of installation.



    A117400E03



    A035284E01
  1. Align the drive rotor spline of the oil pump with the rectangular portion of the crankshaft, then slide the oil pump into place.



    A087353E01
  1. Using an E8 "torx" socket wrench, install the stud bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf }



    A037150E01
  1. Install the oil pump with the 15 bolts and nut as illustrated.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for bolt A
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for bolt B
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for bolt C
    24 N*m{ 245 kgf*cm , 18 ft.*lbf } for bolt D
    24 N*m{ 245 kgf*cm , 18 ft.*lbf } for bolt E

    NOTICE:
    1. Be careful that the chain does not contact the seal packing when installing the oil pump.
    1. Install the engine mounting bracket RH and water pump within 15 minutes after installing the oil pump.



2. INSTALL CRANKSHAFT POSITION SENSOR
  1. Install the sensor with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the sensor connector.



3. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Apply a light coat of engine oil to the O-ring.

  1. Install the camshaft timing oil control valve with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



4. INSTALL ENGINE MOUNTING BRACKET

Torque:
55 N*m{ 561 kgf*cm , 41 ft.*lbf }



5. INSTALL ENGINE MOUNTING SPACER

Torque:
52 N*m{ 530 kgf*cm , 38 ft.*lbf }



6. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH


    A089869E01
  1. Install the engine mounting insulator with the 3 bolts and 4 nuts.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



7. INSTALL CRANKSHAFT PULLEY


A092652E02
  1. Align the hole of the crankshaft pulley with the straight pin, then install the crankshaft pulley.

  1. Using SST, hold the crankshaft pulley and tighten the crankshaft bolt.

    SST
    09213-58013   (91111-50845)
    09330-00021  

    Torque:
    128 N*m{ 1305 kgf*cm , 95 ft.*lbf }

    NOTICE:
    When installing SST, be careful that the bolt which holds SST does not interfere with the chain cover.



8. INSTALL WATER PUMP ASSEMBLY


    B009338E01
  1. Install a new gasket and the water pump with the 3 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



9. INSTALL WATER PUMP PULLEY


    A092654E01
  1. Using SST, install the pump pulley with the 3 bolts.

    SST
    09960-10010   (09962-01000, 09963-00600)

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



10. INSTALL DRIVE BELT
  1. Temporarily install the belt on each pulley.



11. INSTALL PURGE VSV


    A087598E01
  1. Install the purge VSV with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 2 purge line hoses to the purge VSV.

  1. Connect the purge VSV connector.



12. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


A092514E02
  1. Apply seal packing to the 2 locations shown in the illustration, then install the cylinder head cover.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the cylinder head cover within 3 minutes after applying seal packing.
    1. Do not start the engine within 2 hours of installing.



    A035756E01
  1. Install the cylinder head cover with the 9 bolts and 2 nuts.

  1. Using several steps, tighten the bolts and nuts with the specified torque in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the ignition coil with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the brake master cylinder reservoir cover to the cylinder head cover.

  1. Install the wire harness and brake master cylinder reservoir cover with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the fuel injector connector and ignition coil connector.



13. INSTALL WINDSHIELD WASHER JAR ASSEMBLY


A092653E01

Torque:
4.9 N*m{ 50 kgf*cm , 43 in.*lbf } for bolt A
14 N*m{ 143 kgf*cm , 10 ft.*lbf } for bolt B
5.5 N*m{ 56 kgf*cm , 49 in.*lbf } for nut



14. INSTALL RESERVOIR BRACKET

Torque:
8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



15. INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

Torque:
8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



16. INSTALL NO. 2 AIR CLEANER INLET


17. INSTALL AIR CLEANER ASSEMBLY


    A088037E01
  1. Install the air cleaner with the 2 bolts and tighten the clamp.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } for bolt
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf } for clamp



18. INSTALL FRONT COWL TOP PANEL OUTER


    A087419E01
  1. Install the panel with the 7 bolts.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }



    A087418E01
  1. Connect the 4 wire harness clamps.

  1. Install the No. 2 engine room relay block with the 2 bolts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



19. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
  1. Install the windshield wiper motor and wiper link assembly (Click here).



20. ADD ENGINE OIL
  1. Add fresh engine oil and install the oil filler cap.

    Engine oil:

    Oil Grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    1. 5W-30
    2. 10W-30
    (SAE 5W-30 is the best choice for fuel economy and good starting in cold weather.)


    Capacity:

    Item
    Fill amount
    Drain and refill with oil filter change
    3.7 liters (3.9 US qts, 3.3 Imp. qts)
    Drain and refill without oil filter change
    3.4 liters (3.6 US qts, 3.0 Imp. qts)
    Dry fill
    4.1 liters (4.3 US qts, 3.6 Imp. qts)



21. INSTALL SERVICE PLUG GRIP

CAUTION:
Wear insulating gloves.

  1. Joint the service plug grip with the HV battery.

  1. While pushing the service plug grip to the right, rotate the lever to the right.

  1. Slide the lever down to lock the service plug grip in place.

    NOTICE:
    1. The service plug grip must be locked. If not, it may cause DTCs to output.

    2. Do not operate the power switch when the service plug grip is not properly locked. It may damage the hybrid vehicle control ECU in rare cases.


      A089219



22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
  1. When the warning light is illuminated or the battery has been disconnected and reconnected, turning the power switch may not start the system on the first try. If so, turn the power switch again.
  2. With the power switch's power mode changed to ON (IG), disconnect the battery. If the key is not in the key slot during reconnection, DTC B2799 may be output.



    A088356E01
  1. Connect the battery negative cable, and then tighten the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



23. INSTALL REAR NO. 3 FLOOR BOARD


    A088355E02
  1. Install the floor board, and then attach the 4 claws.



24. INSTALL REAR DECK FLOOR BOX


    A088354E01
  1. Install the rear deck floor box to the vehicle.



25. INSTALL REAR NO. 2 FLOOR BOARD


    A088353E01
  1. Install the floor board, and then lock the 2 cover knobs.



26. ADD ENGINE COOLANT (for Engine)
  1. Tighten the drain cock plug of the coolant heat storage tank, then disconnect the vinyl hose.

  1. Tighten the drain cock plug of the engine, then disconnect the vinyl hose.

    Torque:
    13 N*m{ 133 kgf*cm , 9.6 ft.*lbf }

  1. Tighten the drain cock plug of the radiator, then disconnect the vinyl hose.



    A092991E01
  1. Connect a vinyl hose to the bleeder plug of the radiator assembly and the radiator reservoir.

    HINT:
    Insert the vinyl hose inside the radiator reservoir tank.



    A088678E01
  1. Using a 6 mm socket hexagon wrench, loosen the radiator bleeder plug from the radiator support service hole.

  1. Fill the radiator with coolant up to the fill port.

    Standard capacity:
    8.6 liters (9.1 US qts, 7.6 Imp. qts)

    HINT:
    1. When filling coolant, press the radiator hose a few times. If the coolant level goes down, add more coolant.
    2. Amount of coolant to fill: Approximately 2.4 liters (2.5 US qts, 2.1 Imp. qts)
    3. Use of improper coolants may damage the engine cooling system.
    4. Only use "Toyota Super Long Life Coolant", or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology.
    5. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene-glycol concentration is approximately 50% and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.
    6. Observe the coolant level inside the radiator by pressing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add more coolant.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Using a 6 mm socket hexagon wrench, tighten the radiator bleeder plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

  1. Install the radiator cop.

  1. Fill the radiator reservoir tank with coolant to the full level.

  1. Connect the coolant heat storage water pump connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Select the item:
    Powertrain / Engine and ECT / Data List/Activate the Water Pump

    NOTICE:
    1. The water pump motor operates for 30 seconds after WATER PUMP is ON in the ACTIVE TEST mode, then it automatically stops operating.
    2. Do not actuate the water pump motor without coolant filled.



    A088678E01
  1. Using a 6 mm socket hexagon wrench, loosen the radiator bleeder plug from the radiator support service hole.

  1. Remove the radiator cap, then fill the radiator with coolant up to the fill port.

    HINT:
    When filling coolant, press the radiator hose a few times. If the coolant level goes down, add more coolant.

  1. Using a 6 mm socket hexagon wrench, tighten the radiator bleeder plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

  1. Install the radiator cap.

  1. Slowly pour coolant into the radiator reservoir until it reaches the full line.

  1. Disconnect the vinyl hose between the bleeder plug of the radiator assembly and the radiator reservoir tank.

  1. Set the vehicle to inspection mode (Click here).

  1. Warm up the engine until the thermostat is open.

  1. Stop the engine, then wait until the coolant becomes cold. Remove the radiator cap and check the coolant level.

    CAUTION:
    If the engine or radiator is hot, do not remove the radiator cap.

    If the coolant level is lower, add coolant again. Warm up the engine, then check the coolant level.

  1. When the coolant level stops going down, add coolant to the radiator reservoir tank up to the full level.



27. INSPECT FOR COOLANT LEAK (for Engine)
  1. Fill the radiator with engine coolant and attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi) and check for leakage.



28. INSPECT FOR OIL LEAK


29. INSTALL RADIATOR SUPPORT OPENING COVER


30. INSTALL ENGINE UNDER COVER RH


31. INSTALL ENGINE UNDER COVER LH


32. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



33. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.