Home › ENGINE › 1NZ-FXE LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD


    A083547E01
  1. As shown in the illustration, turn the knob to release the lock.

  1. Remove the rear floor board No. 2.



2. REMOVE REAR DECK FLOOR BOX


    A083546E01
  1. Remove the deck floor box rear shown in the illustration.



3. REMOVE REAR NO. 3 FLOOR BOARD


    A083544E01
  1. Remove the rear floor board shown in the illustration.



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



5. REMOVE SERVICE PLUG GRIP


A083545E03

CAUTION:
Wear insulating gloves.

  1. Slide up the lever of the service plug grip. Remove the service plug grip while turning the lever to the left.

  1. Insulate the service plug with insulating tape.



6. REMOVE RADIATOR SUPPORT OPENING COVER


    A088174E01
  1. Remove the 6 clips and radiator support opening cover.



7. REMOVE FRONT WHEEL RH


8. REMOVE ENGINE UNDER COVER LH


9. REMOVE ENGINE UNDER COVER RH


10. DRAIN ENGINE COOLANT (for Engine)
  1. Disconnect the coolant heat storage water pump connector.

  1. Connect a vinyl hose to the drain cock of the radiator.

  1. Connect a vinyl hose to the drain cock of the engine.

  1. Connect a vinyl hose to the drain cock of the coolant heat storage tank.

    CAUTION:
    If the tank has any malfunctions, the tank surface becomes hot. To prevent injuries from burns, do not touch the tank.

  1. Loosen the drain cock plugs of the radiator, engine and coolant heat storage tank, then drain the coolant.

    CAUTION:
    Even if the engine is cold, the coolant in the coolant heat storage tank is still hot. Be careful of the hot coolant when draining it.

    HINT:
    Record the amount of the drained coolant. It will be referred to when refilling the tank with coolant.



  1. Remove the radiator cap.


    A124655E01

  1. Drain the coolant in the radiator reservoir.



11. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, then drain the oil into a container.

  1. Clean the oil drain plug and install it with a new gasket.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }



12. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
  1. Remove the windshield wiper motor and rink assembly (Click here).



13. REMOVE FRONT COWL TOP PANEL OUTER


A087418E01
  1. Remove the 2 bolts and disconnect the No. 2 engine room relay block.

  1. Remove the 4 wire harness clamps.



    A087419E01
  1. Remove the 7 bolts and panel.



14. REMOVE AIR CLEANER ASSEMBLY


A086911E01
  1. Loosen the clamp, then disconnect the No. 1 air cleaner inlet from the air cleaner case.



    A087334E01
  1. Disconnect the mass air flow meter connector, then remove the wire harness clamp.

  1. Loosen the clamp, then remove the 2 bolts and air cleaner assembly.



15. REMOVE NO. 2 AIR CLEANER INLET


A087335E01
  1. Remove the clip and air cleaner inlet.



16. SUSPEND BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY


A087336E01
  1. Disconnect the connector.

  1. Remove the 2 bolts.

  1. Separate the claw fitting, then suspend the brake master cylinder reservoir with a rope.

    NOTICE:
    Be careful of the angle of the brake master cylinder reservoir when suspending to prevent air from coming into the hose.



17. REMOVE RESERVOIR BRACKET


A087337E01
  1. Disconnect the hose from the brake master cylinder reservoir bracket.

  1. Remove the 3 bolts and wire harness clamp, then remove the brake master cylinder reservoir bracket.



18. REMOVE WINDSHIELD WASHER JAR ASSEMBLY


A087338E01
  1. Loosen the bolt which holds the headlight RH.

  1. Disconnect the connector and remove the wire harness clamp.

  1. Remove the bolt and bracket.



    A087339E01
  1. Remove the nut.

  1. Slightly lift the headlight RH and separate the claw fitting, then remove the washer jar.

  1. Disconnect the hose from the washer jar.



19. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


A087340E01
  1. Disconnect the fuel injector connector and ignition coil connector.

  1. Remove the 3 bolts and wire harness clamp, then disconnect the wire harness.



    A087341E01
  1. Remove the brake master cylinder reservoir cover.



    A087343E01
  1. Disconnect the ventilation hose and No. 2 ventilation hose.



    A087344E01
  1. Remove the 4 bolts and 4 ignition coils.



    A066472E01
  1. Remove the 9 bolts and 2 nuts, then remove the cylinder head cover.



20. REMOVE PURGE VSV


A087598E01
  1. Disconnect the purge VSV connector.

  1. Disconnect the 2 purge line hoses from the purge VSV.

  1. Remove the bolt, then remove the purge VSV.



21. REMOVE DRIVE BELT


    A086912E01
  1. Loosen nut A.

  1. Turn adjust bolt B, and then release the belt tension.

  1. Remove the belt.



22. REMOVE WATER PUMP PULLEY


A092654E01
  1. Using SST, hold the pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00600)

  1. Remove the 3 bolts and pump pulley.



23. REMOVE WATER PUMP ASSEMBLY


B009338E01
  1. Remove the 3 bolts and 2 nuts.

  1. Remove the water pump and gasket.



24. REMOVE CRANKSHAFT PULLEY


A122104E01
  1. Using SST, hold the crankshaft pulley and loosen the crankshaft bolt.

    SST
    09213-58013   (91111-50845)
    09330-00021  

    NOTICE:
    When installing SST, be careful that the bolt which holds SST does not interfere with the chain cover.



    A122105E01
  1. Loosen the crankshaft bolt until the 2 to 3 threads of the bolt is tightened to the crankshaft.

  1. Using SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

  1. Remove the crankshaft bolt.



25. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH


A087348E01
  1. Place a transmission jack underneath the engine, then put a wooden block on the jack.



    A087349E01
  1. Remove the 3 bolts and 4 nuts, then remove the engine mounting insulator RH.



26. REMOVE ENGINE MOUNTING SPACER


A087350E01
  1. Remove the 2 bolts and engine mounting spacer.



27. REMOVE ENGINE MOUNTING BRACKET


A087351E01
  1. Remove the 4 bolts and engine mounting bracket.



28. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


A087352E01
  1. Disconnect the connector.

  1. Remove the bolt and camshaft timing oil control valve.



29. REMOVE CRANKSHAFT POSITION SENSOR
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.



30. REMOVE OIL PUMP ASSEMBLY


A066477E01
  1. Remove the 15 bolts and nut.



    A087353E01
  1. Using an E8 "torx" socket wrench, remove the stud bolt.



    A087354E01
  1. Using a screwdriver with its tip wrapped in tape, remove the oil pump by prying out between the cylinder head and cylinder block.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pump assembly, cylinder head and cylinder block.



    A088881E01
  1. Remove the 2 O-rings.