Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › CONDENSER

CONDENSER > INSTALLATION

for Preparation Click here



1. INSTALL CONDENSER ASSEMBLY WITH RECEIVER


    I038558E01
  1. Install the condenser (with receiver) with the 2 bolts.

    Torque:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

    HINT:
    If the condenser is replaced with a new one, add compressor oil to the new condenser.

    Capacity:
    40 cc (1.4 fl. oz.)

    Compressor oil:
    ND-OIL 11 or equivalent



    I038557E01
  1. Install the 2 angles to the condenser (with receiver).



2. INSTALL RADIATOR SUPPORT SUB-ASSEMBLY UPPER RH


    I038556E02
  1. Install the radiator support upper with the 4 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } for bolt A
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf } for bolt B
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf } for bolt C



3. INSTALL RADIATOR SUPPORT SUB-ASSEMBLY UPPER LH


    I038982E02
  1. Install the radiator support upper with the 4 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } for bolt A
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf } for bolt B
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf } for bolt C



4. CONNECT COOLER REFRIGERANT LIQUID PIPE E (TO COOLER UNIT)
  1. Remove the attached vinyl tape from the disconnected parts of the cooler refrigerant liquid pipe E and condenser assembly (with receiver).

  1. Install a new O-ring to the cooler refrigerant liquid pipe E.

  1. Sufficiently apply compressor oil (ND-OIL 11) to the O-ring and the cooler refrigerant liquid pipe E fitting surface.

    Compressor oil:
    ND-OIL 11 or equivalent

    NOTICE:
    1. Do not use any compressor oil other than ND-OIL 11.
    2. If any compressor oil other than ND-OIL 11 is used, compressor motor insulation performance may decrease, resulting in a leakage of electric power.



    I038555E01
  1. Connect the cooler refrigerant liquid pipe E to the condenser (with receiver) with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }



5. CONNECT DISCHARGE HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the disconnected parts of the discharge hose and the condenser (with receiver).

  1. Install a new O-ring to the discharge hose.

  1. Sufficiently apply compressor oil (ND-OIL 11) to the O-ring and the discharge hose fitting surface.

    NOTICE:
    1. Do not use any compressor oil other than ND-OIL 11.
    2. If any compressor oil other than ND-OIL 11 is used, compressor motor insulation performance may decrease, resulting in a leakage of electric power.



    I038554E01
  1. Connect the discharge hose to the condenser (with receiver) with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }



6. INSTALL NO. 1 INVERTER BRACKET


7. INSTALL FRONT BUMPER COVER
  1. Install the front bumper cover (Click here).



8. INSTALL FRONT FENDER LINER RH

HINT:
Use the same procedure described for the LH side.



9. INSTALL FRONT FENDER LINER LH


    B130315
  1. Install the fender liner with the clip.



10. CHARGE REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Amount:
    450 +-30 g (15.9 +-1.1 oz.)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)


    I030082E09

    NOTICE:
    1. Do not turn the A/C on before charging refrigerant as the cooler compressor does not work properly without any refrigerant. Operating without any refrigerant causes it to overheat.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.

    HINT:
    Prepare a service can to recharge the refrigerant if using the refrigerant gas collected with the Freon collection/recycling device because the collective rate of the device is approximately 90%.



11. WARM UP COMPRESSOR
  1. Turn the A/C switch on for at least 1 minute to warm up the compressor.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C on after removing and installing the cooler refrigerant lines (including the compressor) to prevent damage to the compressor.



12. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, inspect for refrigerant leak gas using a halogen leak detector.

  1. After recharging the refrigerant gas, prepare the vehicle for a refrigerant gas leakage check by making sure the following conditions are met.

    1. The ignition switch is OFF.

    2. The vehicle is in a place with good air ventilation and without any volatile gases, such as evaporated gasoline or exhaust gas. The detector is very sensitive to volatile gases. If volatile gases are unavoidable, the vehicle must be lifted up.

    3. Some refrigerant remains in the refrigerant system.

    4. The compressor is OFF and its pressure is approximately 392 to 588 kPa (4 to 6 kgf/cm2).



    N014519E04
  1. Bring the gas leak detector close to the drain hose with the detector's power off.

    HINT:
    1. After the blower motor has stopped, leave the cooling unit as it is for more than 15 minutes.
    2. Expose the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to the volatile gases.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and wait for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.