Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1365/54    Accumulator Pressure Sensor Malfunction

for Preparation Click here


DESCRIPTION

The accumulator (ACC) pressure sensor is built into the brake actuator.
The skid control ECU detects the accumulator pressure from the data sent from the accumulator pressure sensor, and then runs and stops the pump motor by operating the motor relay.
DTCs may be output if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1365/54
211
Sensor power 1 (VCM1) voltage is 4.7 V or less or 5.3 V or more for at least 0.05 sec.
  1. Brake actuator assembly (accumulator pressure sensor)
  2. Skid control ECU
C1365/54
212
Ratio of accumulator pressure sensor output voltage (PACC) to sensor power 1 (VCM1) voltage is 5% or less or 90.5% or more for at least 0.05 sec.
  1. Brake actuator assembly (accumulator pressure sensor)
  2. Skid control ECU
C1365/54
214
Total wheel cylinder pressure sensor exceeds 12 MPa after depressing brake pedal, but accumulator pressure sensor output voltage (PACC) changes less than 0.5 MPa for at least 0.5 sec.
  1. Brake actuator assembly (accumulator pressure sensor)
  2. Skid control ECU
C1365/54
215
Ratio of accumulator pressure sensor output voltage (PACC) to sensor power 1 (VCM1) voltage is 90.5% or less for at least 0.1 sec. during self-diagnosis.
  1. Brake actuator assembly (accumulator pressure sensor)
  2. Skid control ECU
C1365/54
216
Voltage difference is 0.3 V or more before and after changing the pull up resistance in sensor signal input circuit (loose contact).
  1. Brake actuator assembly (accumulator pressure sensor)
  2. Skid control ECU

WIRING DIAGRAM


C126252E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization of linear solenoid valve and calibration (Click here).

1.CHECK WIRE HARNESS (SKID CONTROL ECU - BRAKE ACTUATOR)


    F047492E11
  1. Disconnect the S7 ECU connector.

  1. Disconnect the A2 actuator connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S7-8 (E) - A2-45 (E1)
    Below 1 Ω
    S7-9 (VCM1) - A2-35 (VCM1)
    Below 1 Ω
    S7-21 (PACC) - A2-46 (PACC)
    Below 1 Ω
    S7-31 (PCK1) - A2-37 (PCK1)
    Below 1 Ω
    S7-8 (E) - Body ground
    10 kΩ or higher
    S7-9 (VCM1) - Body ground
    10 kΩ or higher
    S7-21 (PACC) - Body ground
    10 kΩ or higher
    S7-31 (PCK1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2.CHECK SKID CONTROL ECU (VCM1 VOLTAGE)


    F047485E66
  1. Measure the voltage of the connector.

    HINT:
    Measure the voltage from behind the connector with the connector connected to the skid control ECU.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S7-9 (VCM1) - S7-1 (GND)
    Power switch ON (READY)
    4.75 to 5.25 V



NG
REPLACE SKID CONTROL ECU
OK


3.CHECK SKID CONTROL ECU (PACC VOLTAGE)
  1. Check the auxiliary battery voltage.

    Standard voltage:
    10 to 14 V

  1. Depress the brake pedal to operate the pump motor, and then check that the pump motor stops.



    F047485E72
  1. Measure the voltage of the connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    S7-21 (PACC) - S7-1 (GND)
    3.3 to 4.7 V

    NOTICE:
    1. Do not depress the brake until after the pump motor stops and the voltage check is finished in order to keep the accumulator pressure.
    2. Check from behind the connector with the connector connected to the skid control ECU.
    3. Do not use a Data List, as the sensor itself must be checked.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


4.READ VALUE OF TECHSTREAM (ACCUMULATOR PRESSURE SENSOR)
  1. Check the Data List for proper functioning of the accumulator pressure sensor.

  1. Depress the brake pedal 4 or 5 times to operate the pump motor, and check the output value on Techstream with the motor stopped (no braking).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Accumulator Sensor 1
    Accumulator pressure sensor 1 / Min.: 0 V, Max.: 5 V
    Specified value: 3.2 to 4.0 V
    -

    OK:
    Accumulator pressure sensor voltage does not drop.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK

REPLACE SKID CONTROL ECU