Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1311/11    Open in Main Relay 1 Circuit

DTC    C1312/12    Short in Main Relay 1 Circuit

DTC    C1313/13    Open in Main Relay 2 Circuit

DTC    C1314/14    Short in Main Relay 2 Circuit

for Preparation Click here


DESCRIPTION

ABS main relay 1 (ABS NO. 1 relay) supplies power to the changeover solenoid and the linear solenoid.
ABS main relay 2 (ABS NO. 2 relay) goes on for approximately 5 seconds after the power switch is turned off and the braking effort signal input is terminated. ABS main relay 2 (ABS NO. 2 relay) supplies electricity and maintains operating condition for the brake system when the power switch is OFF.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1311/11
1
When either condition below is met:
  1. Relay contact is off (BS 1 terminal is less than 3.5 V) for at least 0.2 sec. when R1+ terminal voltage is 9.5 V or more and main relay 1 is on.
  2. R1+ terminal voltage is less than 9.5 V and main relay 1 cannot be on for at least 0.2 sec. when main relay 1 is turned on (BS 1 terminal is 3.5 V or more).
  1. ABS main relay 1
    (ABS NO. 1 relay)
  2. Skid control ECU
  3. Harness and connector
C1312/12
3
Relay contact is on for at least 4 sec. when main relay 1 is off.
  1. ABS main relay 1
    (ABS NO. 1 relay)
  2. Skid control ECU
  3. Harness and connector
C1313/13
4
When either condition below is met:
  1. Relay contact is off (BS2 terminal is less than 3.5 V) for at least 0.2 sec. when R2+ terminal voltage is 9.5 V or more and main relay 2 is on.
  2. R2+ terminal voltage is less than 9.5 V and main relay 2 cannot be on for at least 2 sec. when main relay 2 is turned on (BS 1 terminal is 3.5 V or more).
  1. ABS main relay 2
    (ABS NO. 2 relay)
  2. Skid control ECU
  3. Harness and connector
C1314/14
6
Relay contact is on for at least 4 sec. when main relay 2 is off.
  1. ABS main relay 2
    (ABS NO. 2 relay)
  2. Skid control ECU
  3. Harness and connector

WIRING DIAGRAM


C126258E03


C153495E01


C126259E02


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization of linear solenoid valve and calibration (Click here).

1.PERFORM ACTIVE TEST BY TECHSTREAM (ABS NO. 1 RELAY, ABS NO. 2 RELAY)
  1. Select the Active Test for the proper functioning of the ABS NO. 1 and ABS NO. 2 relays.

    ABS / VSC / TRAC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ECB* Main Relay 1
    Main relay 1
    Relay ON / OFF
    Operation of solenoid (clicking sound) can be heard
    ECB* Main Relay 2
    Main relay 2
    Relay ON / OFF
    Operation of solenoid (clicking sound) can be heard
    *: Electronically Controlled Brake

    OK:
    Operation sound of ABS NO. 1 relay and ABS NO. 2 relay should be heard.



NG
Go to step 3
OK


2.CHECK SKID CONTROL ECU (BS1, BS2 VOLTAGE)


    F047485E61
  1. Measure the voltage of the connectors.

    HINT:
    Measure the voltage from behind the connector with the connector connected to the skid control ECU.

    Standard voltage:
    Tester Connection
    Specified Condition
    S7-3 (BS1) - Body ground
    10 to 14 V
    S10-7 (BS2) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE SKID CONTROL ECU 

3.INSPECT FUSE (ABS MAIN1, ABS MAIN2)


    F047495E02
  1. Remove the ABS MAIN1 and ABS MAIN2 fuses from the engine room relay block.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


4.INSPECT ABS MAIN RELAY (Marking: ABS NO. 1, ABS NO. 2)


    B060778E03
  1. Remove the ABS NO. 1 and ABS NO. 2 relays from the engine room relay block.

  1. Measure the resistance of the relays.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2



NG
REPLACE RELAY
OK


5.CHECK SKID CONTROL ECU (+BI1, +BI2 VOLTAGE)


    F047485E62
  1. Measure the voltage of the connectors.

    HINT:
    Measure the voltage from behind the connector with the connector connected to the skid control ECU.

    Standard voltage:
    Tester Connection
    Specified Condition
    S8-3 (+BI1) - Body ground
    10 to 14 V
    S9-5 (+BI2) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.CHECK SKID CONTROL ECU (+BO1, +BO2, R1+, R2+ VOLTAGE)


    F047485E76
  1. Measure the voltage of the connectors.

    HINT:
    Measure the voltage from behind the connector with the connector connected to the skid control ECU.

    Standard voltage:
    Tester Connection
    Specified Condition
    S7-2 (R1+) - Body ground
    10 to 14 V
    S8-5 (+BO1) - Body ground
    10 to 14 V
    S9-4 (+BO2) - Body ground
    10 to 14 V
    S10-17 (R2+) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7.CHECK SKID CONTROL ECU (BS1, BS2 VOLTAGE)


    F047485E64
  1. Measure the voltage of the connectors.

    HINT:
    Measure the voltage from behind the connector with the connector connected to the skid control ECU.

    Standard voltage:
    Tester Connection
    Specified Condition
    S7-3 (BS1) - Body ground
    10 to 14 V
    S10-7 (BS2) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE SKID CONTROL ECU