Home › HYBRID SYSTEM › P112 HYBRID BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0AAC    Hybrid Battery Pack Air Temperature Sensor "A" Circuit

for Preparation Click here


DESCRIPTION

The intake air temperature sensor is provided on the HV battery assembly. Its resistance value varies with the changes in the intake air temperature. The characteristics of the intake air temperature sensor are the same as the battery temperature sensors .
The battery ECU uses the signals from the intake air temperature sensor for adjusting the air flow speed of the battery blower.

DTC No.
DTC Detection Condition
Trouble Area
P0AAC
Temperature detected by intake air temperature sensor is lower than standard (open) or higher than standard (short) (1 trip detection logic)
  1. HV battery assembly (intake air temperature sensor)
  2. Battery ECU

HINT:
After confirming DTC P0AAC, enter the following menus on the Techstream: Powertrain / HV Battery / Data List. Then, confirm the temperature of the intake ambient air to the battery pack by checking "Batt Inside Air".

Temperature Displayed
Malfunction
-45°C (-49°F) or less
Open or +B short circuit
95°C (203°F) or more
GND short circuit


MONITOR DESCRIPTION

If the temperature indicated by the intake air temperature sensor is lower than the standard level (open), or is higher than the standard level (short), the battery ECU determines that a malfunction has occurred. If the battery ECU detects an abnormal intake air temperature, it will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0AAC: Intake cooling air temperature sensor/Range check
Required sensors/components
Intake air temperature sensor
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TOYOTA's intellectual property
Other conditions belong to TOYOTA's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Resistance of intake air temperature sensor
1.108 kΩ or less or 247.7 kΩ or more

COMPONENT OPERATING RANGE


Intake air temperature sensor
9 to 11 kΩ (at 25°C (77°F))

WIRING DIAGRAM


C118378E01


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from reconnecting it while you are servicing the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes are required to discharge the high-voltage condenser inside the inverter.

1.READ DTC OUTPUT (DTC P0A1F IS OUTPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch ON (IG) and the tester ON.

  1. Enter the following menus: Powertrain / HV Battery / DTC.

  1. Read DTCs.

    Result:
    DTC P0A1F is output



YES
REPLACE BATTERY ECU
NO


2.CHECK CONNECTION OF INTAKE AIR TEMPERATURE SENSOR CONNECTOR

CAUTION:
Wear insulated gloves before performing the following operation.

  1. Turn the power switch OFF.

  1. Remove the service plug grip (Click here).

    NOTICE:
    Turning the power switch ON (READY) with the service plug grip removed could cause a malfunction. Therefore, never turn the power switch ON (READY) in this state.



    A093174E05
  1. Check the connection condition of the B13 battery ECU connector.

    OK:
    Connector has been connected securely and there is no poor connection.

    HINT:
    Since the intake air temperature sensor is not available it self, if replacement is required, replace the entire HV battery assembly.



NG
CONNECT SECURELY
OK

REPLACE HV SUPPLY BATTERY ASSEMBLY