Home › SUSPENSION & AXLE › SUSPENSION › FRONT SHOCK ABSORBER WITH COIL SPRING

FRONT SHOCK ABSORBER WITH COIL SPRING > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.



1. INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING


    F046083E01
  1. Insert the 2 bolts from the front side of the vehicle and install the front shock absorber with coil spring to the steering knuckle.

  1. Place a wooden block between the front shock absorber with coil spring and a jack. Slowly raise the jack and install the front shock absorber with coil spring (upper side) to the vehicle.

  1. Install the front shock absorber with coil spring (upper side) with the 3 nuts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



    F046086E01
  1. Install the front shock absorber with coil spring to the steering knuckle with the 2 nuts.

    Torque:
    153 N*m{ 1,560 kgf*cm , 113 ft.*lbf }



    C080880E01
  1. Connect the front flexible hose No. 1 and the speed sensor front LH to the shock absorber with the bolt.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the speed sensor front while installing.



2. CONNECT FRONT STABILIZER LINK ASSEMBLY LH


    F046088E01
  1. Connect the front stabilizer link to the front shock absorber with coil spring with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    Use a 6 mm hexagon wrench to hold the stud if the ball joint turns together with the nut.



3. INSTALL WINDSHIELD WIPER MOTOR AND LINK


    I038371E01
  1. Install the windshield wiper motor & link with the 5 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



4. INSTALL COWL TOP VENTILATOR LOUVER LH


I038369E02
  1. Attach the 8 claws and install the louver.

  1. Install the clip.



5. INSTALL COWL TOP VENTILATOR LOUVER RH


I038370E02
  1. Attach the 8 claws and install the louver.

  1. Install the clip.



6. INSTALL HOOD TO COWL TOP SEAL


I038368E02
  1. Attach the 8 clips and install the cowl to seal.



7. INSTALL FRONT WIPER ARM LH


    I040975E01
  1. Clean the wiper arm serration with a round file or equivalent (when reinstalling).

  1. Clean the wiper pivot serration with a wire brush.



    I040976E03
  1. Install the front wiper arm LH with the nut so that the front wiper blade comes to the position shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    While installing the nut, hold down the arm hinge by hand.



8. INSTALL FRONT WIPER ARM RH


    I040977E03
  1. Clean the wiper arm serration with a round file or equivalent (when reinstalling).

  1. Clean the wiper pivot serration with a wire brush.

  1. Install the front wiper arm RH with the 2 nuts so that the front wiper blade comes to the position shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    While installing the nut, hold down the arm hinge by hand.

  1. Operate the front wipers while spraying water or washer fluid on the windshield glass. Ensure that the wipers function properly and there is no interference with the body.



9. INSTALL FRONT WIPER ARM HEAD CAP


10. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



11. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
  1. Inspect and adjust the front wheel alignment (Click here).