Home › SUSPENSION & AXLE › SUSPENSION › FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT > ADJUSTMENT

for Preparation Click here



1. INSPECT TIRE
  1. Inspect the tires (Click here).



2. MEASURE VEHICLE HEIGHT


F046082E03

Standard vehicle height:
Item
Specified Condition
Front (A - B)
95 mm (3.74 in.)
Rear (D - C)
62 mm (2.44 in.)

Measuring points:
A:
Ground clearance of front wheel center
B:
Ground clearance of lower arm No. 1 set bolt center
C:
Ground clearance of rear axle carrier bush set bolt center
D:
Ground clearance of rear wheel center

NOTICE:
Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

HINT:
Bounce the vehicle at the corners up and down to stabilize the suspension and inspect the vehicle height.



3. INSPECT TOE-IN


SA03213E02

Standard toe-in:
Item
Specified Condition
Toe-in (total)
A + B: 0° +-12' (0° +-0.2°)
C - D: 0 +-2 mm (0 +-0.08 in.)

HINT:
  1. Measure "C - D" only when "A + B" cannot be measured.
  2. If the toe-in is not within the specified range, adjust it at the rack ends.



4. ADJUST TOE-IN
  1. Measure the thread lengths of the right and left rack ends.

    Standard difference in thread length:
    1.5 mm (0.059 in.) or less

  1. Remove the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

    1. Extend the shorter rack end if the measured toe-in deviates toward the outer-side.

    2. Shorten the longer rack end if the measured toe-in deviates toward the inner-side.

  1. Turn the right and left rack ends by an equal amount to adjust toe-in.

    HINT:
    Try to adjust toe-in to the center of the specified range.



    F046085E01
  1. Make sure that the lengths of the right and left rack ends are the same.

    Standard :
    0 +-1 mm (0.0039 in.)

  1. Torque the tie rod end lock nuts.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Temporarily tighten the lock nut while holding the hexagonal part of the steering rack end so that the lock nut and the steering rack end do not turn together. Hold the width across the flat part of the tie rod end and tighten the lock nut.

  1. Place the boots on the seats and install the clips.

    HINT:
    Make sure that the boots are not twisted.

  1. Perform VSC system calibration (Click here).



5. INSPECT WHEEL ANGLE


    C118572E01
  1. Fully turn the steering wheel to the left and right and measure the turning angle.

    Standard wheel turning angle:
    Item
    Specified Condition
    Inside wheel
    40° 35' +-2° (40.58° +-2°)
    Outside wheel:
    Reference
    34° 15' (34.25°)

    1. If the right and left inside wheel angles differ from the specified range, check the right and left rack end lengths.



6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


    Z003382E08
  1. Put the front wheel on the center of the alignment tester.

  1. Remove the center ornament.

  1. Install the camber-caster-steering axis inclination gauge at the center of the axle hub or drive shaft.

  1. Inspect the camber, caster and steering axis inclination.

    Standard camber, caster and steering axis inclination:
    Item
    Specified Condition
    Camber
    Right-left error
    -0° 35' +-45' (-0.58° +-0.75°)
    45' (0.75°) or less
    Caster
    Right-left error
    3° 10' +-45' (3.17° +-0.75°)
    45' (0.75°) or less
    Steering axis inclination
    Right-left error
    12° 35' +-45' (12.58° +-0.75°)
    45' (0.75°) or less

    NOTICE:
    1. Inspect with an empty vehicle (without the spare tire or tools).
    2. The maximum tolerance of the right and left difference for the camber and caster is 45' or less.

  1. Remove the camber-caster-steering axis inclination gauge and attachment.

  1. Install the center ornament.
    If the caster and steering axis inclination are not within the specified values after the camber has been correctly adjusted, recheck the suspension parts for damage and/or wear.



7. ADJUST CAMBER


F046086E01
F047225E02
F047338E01

C125767E02


C125768E02

NOTICE:
Inspect toe-in after the camber has been adjusted.

(a) Remove the front wheel.
(b) Remove the 2 nuts on the lower side of the shock absorber.

NOTICE:
When removing the nut, stop the bolt from rotating and loosen the nut.

(c) Clean the installation surfaces of the shock absorber and the steering knuckle.
(d) Temporarily install the 2 nuts.
(e) Fully push or pull the front axle hub in the direction of the required adjustment.
(f) Tighten the nuts.

Torque:
153 N*m{ 1,560 kgf*cm , 113 ft.*lbf }

NOTICE:
Keep the bolts from rotating and torque the nuts.

(g) Install the front wheel.

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

(h) Check the camber.
If the measured value is not within the specified range, calculate the required adjustment amount using the formula below.

Camber adjustment amount:
Center of the specified range - Measured value

Check the installed bolt combination. Select appropriate bolts from the table below to adjust the camber to within the specified range.

Standard selection table:
Item
Selection Table
Move the axle toward (+) in step (e)
Refer to table (1) (Move the axle toward positive side)
Move the axle toward (-) in step (e)
Refer to table (2) (Move the axle toward negative side)

(i) Measure the camber with the bolts currently installed and check the amount of looseness from the specified range. (Ex: The measured value is - 1°35')
(j) Determine whether the direction of the required adjustment is toward the positive or negative side. (Ex: Refer to table (1) (Move the axle toward positive side))
(k) Check the required adjustment amount from the measured value. (Table (1), Table (2)) (Ex: Select "Adjust value: 0°45' to 1°00")
(l) Check the currently installed bolt combination. (Ex: " Installed bolt 1: no dot; Installed bolt 2: 2 dots")
(m) Select the adjusting bolts. (Ex: "Selected Bolt Combination" results in F for installed bolt 1: 3 dots; Installed bolt 2: 3 dots)
(n) Measure the alignment again and check that it is within the specified range. (Ex: Measured value is within -0° 35' +-45')
The body and suspension may be damaged if the camber is not correctly adjusted according to the above table.

NOTICE:
Replace the nut with a new one when replacing the bolt.

(o) Repeat the steps mentioned above. At step (b), replace 1 or 2 selected bolts.

HINT:
Replace 1 bolt at a time when replacing 2 bolts.

The body and suspension may be damaged if the camber is not correctly adjusted according to the above table.
(p) Repeat the steps mentioned above. At step (b), replace 1 or 2 selected bolts.

NOTICE:
Replace the nut with a new one when replacing the bolt.

HINT:
Replace 1 bolt at a time when replacing 2 bolts.