Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER WINDOW REGULATOR MASTER SWITCH

E124642E01

  1. Disconnect the P17 switch connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (P17-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    BW (P17-7) - E (P17-1)
    W - W-B
    Regulator motor power supply
    Always
    10 to 14 V
    B (P17-6) - E (P17-1)
    L - W-B
    Master switch power supply
    Power switch ON (IG)
    10 to 14 V
    BDR (P17-11) - E (P17-1)
    V - W-B
    Master switch power supply
    Power switch ON (IG)
    10 to 14 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the P17 switch connector.

  4. Reset the power window motor (Click here).

  5. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DU (P17-4) - E (P17-1)
    Y - W-B
    Power window motor UP output
    Power switch ON (IG), driver side power window switch OFF
    Below 1 V
    DU (P17-4) - E (P17-1)
    Y - W-B
    Power window motor UP output
    Power switch ON (IG), driver side power window switch UP (manual operation)
    10 to 14 V
    DU (P17-4) - E (P17-1)
    Y - W-B
    Power window motor UP output
    Power switch ON (IG), driver side power window fully open
    Below 1 V
    DU (P17-4) - E (P17-1)
    Y - W-B
    Power window motor UP output
    Power switch ON (IG), driver side power window switch UP (AUTO operation)
    10 to 14 V
    DU (P17-4) - E (P17-1)
    Y - W-B
    Power window motor UP output
    Power switch ON (IG), driver side power window fully closed
    Below 1 V
    DD (P17-9) - E (P17-1)
    G - W-B
    Power window motor DOWN output
    Power switch ON (IG), driver side power window switch OFF
    Below 1 V
    DD (P17-9) - E (P17-1)
    G - W-B
    Power window motor DOWN output
    Power switch ON (IG), driver side power window switch DOWN (manual operation)
    10 to 14 V
    DD (P17-9) - E (P17-1)
    G - W-B
    Power window motor DOWN output
    Power switch ON (IG), driver side power window fully closed
    Below 1 V
    DD (P17-9) - E (P17-1)
    G - W-B
    Power window motor DOWN output
    Power switch ON (IG), driver side power window switch DOWN (AUTO operation)
    10 to 14 V
    DD (P17-9) - E (P17-1)
    G - W-B
    Power window motor DOWN output
    Power switch ON (IG), driver side power window fully open
    Below 1 V
    VCC (P17-3) - GND (P17-2)
    G - O
    1. Power window motor power source
    2. Power window motor sensor ground
    Always
    10 to 14 V

    1. If the result is not as specified, the master switch may have a malfunction.

  6. Check the AUTO light illumination.

    1. When turning the power switch ON (IG), check that the AUTO light illuminates (green).


CHECK DRIVER SIDE JUNCTION BLOCK (MAIN BODY ECU)

E124647E01

  1. Disconnect the 1A, 1D, 1E and 1B junction block connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    ECUB (1A-30) - Body ground
    R - Body ground
    +B (ECUB) power supply
    Always
    10 to 14 V
    ALTB (1B-1) - Body ground
    W - Body ground
    +B (power system, generator system) power supply
    Always
    10 to 14 V
    KSW (1E-26) - Body ground
    Y - Body ground
    Halfway switch input
    No key in key slot
    10 kΩ or higher
    KSW (1E-26) - Body ground
    Y - Body ground
    Halfway switch input
    Key inserted
    Below 1 Ω
    DCTY (1D-21) - Body ground
    V - Body ground
    Driver side courtesy switch input
    Driver side door closed
    10 kΩ or higher
    DCTY (1D-21) - Body ground
    V - Body ground
    Driver side courtesy switch input
    Driver side door open
    Below 1 Ω
    PCTY (1D-24) - Body ground P
    BR - Body ground
    Passenger side courtesy switch input
    Passenger side door closed
    10 kΩ or higher
    PCTY (1D-24) - Body ground
    BR - Body ground
    Passenger side courtesy switch input
    Passenger side door open
    Below 1 Ω
    GND (1E-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the 1A, 1D, 1E and 1B junction block connectors.

  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    KSW (1E-26) - Body ground
    Y - Body ground
    Halfway switch input
    No key in key slot
    10 to 14 V
    KSW (1E-26) - Body ground
    Y - Body ground
    Halfway switch input
    Key inserted
    Below 1 V

    1. If the result is not as specified, the junction block (main body ECU) may have a malfunction.