Home › BODY › ENGINE HOOD / DOOR › FRONT DOOR

FRONT DOOR > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT DOOR WEATHERSTRIP LH
  1. Install the weatherstrip and attach the clips.



2. INSTALL FRONT DOOR CHECK ASSEMBLY LH


    B061463E05
  1. Apply MP grease to the sliding areas of the check.

  1. Install the check to the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent

  1. Install the check to the body panel with the bolt.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



3. INSTALL FRONT DOOR OUTSIDE HANDLE PAD REAR


B083064E01
  1. Attach the 2 claws to install the pad.



4. INSTALL FRONT DOOR OUTSIDE HANDLE PAD FRONT


B084266E01
  1. Attach the 2 claws to install the pad.



5. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    B077632E03
  1. Install the outside handle link.

  1. Apply MP grease to the sliding areas of the frame.

  1. Using a T30 "torx" socket wrench, install the frame with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the No. 1 stiffener cushion with the 2 screws.



6. INSTALL FRONT DOOR LOCK ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the door lock.

  1. Install new door lock wire harness packing.

    NOTICE:
    1. When reinstalling the door lock, always use new packing.
    2. Do not allow grease or dirt to contaminate the gap between the door panel and packing.
    3. Old packing or damaged packing cannot effectively protect against water, which can damage the door lock.



    B065961E02
  1. Insert the control rod into the door lock, and then set it to the door panel.

    NOTICE:
    Make sure that the rod is securely engaged with the lock.



    B066894E02
  1. Apply adhesive to the threads of the 3 screws.

    Adhesive:
    Toyota Genuine 1324, Three Bond 1324 or Equivalent

  1. Using a T30 "torx" wrench, install the door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the door lock connector.



7. INSTALL FRONT DOOR OUTSIDE HANDLE LH


8. INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH


    B061438E11
  1. Using a T30 "torx" wrench, install the cover (with the door lock key cylinder installed) with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 37 in.*lbf }

  1. Install the hole plug.



9. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER LH


    B075144E01
  1. Install the frame with the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }



10. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    B070074E01
  1. Using a T25 "torx" driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



11. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    B075151E02
  1. Apply MP grease to the sliding and rotating areas of the window regulator.

    NOTICE:
    Do not apply grease to the spring of the window regulator.



    B077024E01
  1. Loosely install the bolt labeled A onto the window regulator.

  1. Insert the window regulator into the door panel. Use the bolt labeled A to hand the window regulator on the door panel.

  1. Install the window regulator with the 5 bolts and tighten the bolt labeled A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Be careful not to drop the window regulator as it may become damaged.

  1. Connect the window regulator connector.



12. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    B062423E04
  1. Install the glass run.

    NOTICE:
    Be careful not to damage the glass.

  1. Insert the door glass into the door panel along the glass run as indicated by the arrow marks in the illustration.



    B075147E01
  1. Install the door glass to the window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



13. INSTALL DOOR FRAME GARNISH LH
  1. Attach the claws to install the garnish.



14. INSTALL FRONT DOOR WINDOW FRAME MOULDING REAR LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with white gasoline.



  1. If reusing the moulding:
    Clean the moulding and install new double-sided tape.

    1. Using a heat light, heat the moulding.

    2. Remove the double-sided tape from the moulding.

    3. Wipe off any tape adhesive residue with white gasoline.



    4. B074182E03
    5. Install new double-sided tape to the moulding.

      NOTICE:
      Install the double-sided tape exactly according to the specifications below.

      Standard measurement:
      Area
      Specified Condition
      A
      (1) 440.0 mm (17.323 in.)
      (2) 37.0 mm (1.457 in.)
      B
      5.0 mm (0.197 in.)
      C
      0.8 mm (0.032 in.)

  1. Install the moulding.

    1. Using a heat light, heat the vehicle body and moulding.

    2. Remove the peeling paper from the face of the moulding.

      NOTICE:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Install the moulding with the screw.

      NOTICE:
      Do not apply excessive force to the moulding. Apply steady pressure with your thumbs.



15. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH


    B132614
  1. Attach the claws to install the moulding.

    HINT:
    Confirm that the moulding is firmly installed.



16. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


    I036713E03
  1. Using an air riveter or hand riveter, install the speaker with 3 new rivets.

    HINT:
    Install the new strike rivets in the order shown in the illustration.

    NOTICE:

    1. H002440E04
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. H002441E03
      Confirm that the rivets are seated properly against the speaker. Do not tilt the riveter when installing the rivet to the speaker. Do not leave any space between the rivet head and speaker.

    3. H002442E03
      Do not leave any space between the speaker and door. Firmly hold together the 2 items while installing the rivet.

  1. Connect the connector.



17. INSTALL FRONT DOOR SERVICE HOLE COVER LH


    B075138E01
  1. Install the No. 2 service hole cover with the 3 screws.

  1. Apply butyl tape to the door as shown in the illustration.

  1. Install a new service hole cover.

    HINT:
    1. When installing the service hole cover, pull out the links and connectors through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.

  1. Install the trim bracket with the 2 screws.



18. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH


    B075148E01
  1. Install the mirror with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the mirror connector.



19. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


B068930E17
  1. Move the inside handle in the direction indicated by the arrow in the illustration to install the inside handle.

  1. Connect the 2 cables to the inside handle.



20. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


B075137E02
  1. Attach the 7 clips to install the trim board.

  1. Install the screw.



21. INSTALL FRONT ARMREST BASE PANEL UPPER LH
  1. for Driver's Side:
    Install the window regulator master switch to the armrest upper base panel with the 3 screws.

  1. Connect the switch connector.



    B075142E03
  1. Attach the 2 clips and 4 claws to install the armrest base panel (with the window regulator master switch).

  1. for Passenger's Side:
    Attach the 2 claws to install the power window regulator switch.

  1. Attach the 2 claws to install the door control switch.

  1. Connect the connector.



    B075143E03
  1. Attach the 2 clips and 4 claws to install the armrest upper base panel together with the 2 switches.



22. INSTALL DOOR PULL HANDLE


B075150E01
  1. Install the pull handle with the screw.



23. INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH


B076973E07
  1. Attach the 3 claws to install the bezel.



24. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH


B075149E02
  1. Attach the 2 clips to install the garnish.



25. CONNECT CABLE TO BATTERY NEGATIVE TERMINAL


26. INSTALL NO. 3 REAR FLOOR BOARD


27. INSTALL REAR DECK FLOOR BOX


28. INSTALL NO. 2 REAR FLOOR BOARD


29. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).



30. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.