Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1625/22    Front Passenger Side - Side Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The side airbag sensor RH consists of the safing sensor, the diagnostic circuit and the lateral deceleration sensor. The center airbag sensor receives signals from the lateral deceleration sensor and determines whether or not the SRS should be activated.
DTC B1625/22 is recorded when a malfunction is detected in the side airbag sensor RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1625/22
When one of following conditions is met:
  1. Center airbag sensor receives line short signal, open signal, short to ground or B+ short signal from side airbag sensor RH sensor for 2 seconds
  2. Side airbag sensor RH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire No. 2
  2. Center airbag sensor
  3. Side airbag sensor RH

WIRING DIAGRAM


C123527E07


INSPECTION PROCEDURE

1.CHECK FOR DTC
C130785E01
  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1622/25 is not output.

    HINT:
    DTCs other than DTC B1622/25 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and side airbag sensor RH.

    OK:
    Connectors are connected.



NG
CONNECT CONNECTOR
OK


3.CHECK FLOOR WIRE NO. 2 (OPEN)
C130786E03
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor RH.

  1. Using a service wire, connect terminals S19-2 (VUPR) and S19-1 (ESR) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A19-22 (VUPP) - A19-20 (ESP)
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


4.CHECK FLOOR WIRE NO. 2 (SHORT)
C123579E04
  1. Disconnect the service wire from connector C.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A19-22 (VUPP) - A19-20 (ESP)
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


5.CHECK FLOOR WIRE NO. 2 (TO B+)
C123579E04
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A19-22 (VUPP) - Body ground
    Below 1 V
    A19-20 (ESP) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


6.CHECK FLOOR WIRE NO. 2 (TO GROUND)
C123579E04
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A19-22 (VUPP) - Body ground
    1 MΩ or higher
    A19-20 (ESP) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


7.CHECK SIDE AIRBAG SENSOR RH
H100847E04
  1. Connect the connector to the center airbag sensor.

  1. Interchange the side airbag sensor RH with the side airbag sensor LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1620/21 and B1625/22 are not output
    A
    DTC B1625/22 is output
    B
    DTC B1620/21 is output
    C

    HINT:
    DTCs other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

C
REPLACE SIDE AIRBAG SENSOR RH
A

USE SIMULATION METHOD TO CHECK