Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0446    Evaporative Emission Control System Vent Control Circuit

for Preparation Click here


DESCRIPTION


DTC
DTC Detection Condition
Trouble Area
P0446
One of the following condition is met while vehicle is driving (2 trip detection logic):
  1. No change in fuel tank pressure when purge VSV and purge flow switching valve are opened
  2. No change in fuel tank pressure when fuel tank is depressurized to 740 mmHg and purge VSV is closed
  1. Leak from EVAP system
  2. Purge flow switching valve
  3. Purge VSV
  4. Vent valve
  5. Fuel tank pressure sensor
This DTC is designed to detect the purge flow switching valve (3-way VSV) malfunction. If the malfunction is detected while the vehicle is running, the ECM illuminates the MIL and sets a DTC (2 detection logic).
The purge flow switching valve located on the canister is used to detect leakage from the bladder tank into the fuel tank. The valve opens during the bladder tank leak check. Then, the fuel tank's fuel vapor flows to the intake manifold without passing the canister.

MONITOR DESCRIPTION

  1. Purge flow switching valve is stuck OFF (Closed)
    The purge flow switching valve opens when the purge VSV opens while the vehicle is running. Then, the fuel tank pressure drops 2 mmHg or more when the purge flow switching valve is normal. If the pressure does not change, the ECM interprets this as a malfunction. The ECM illuminates the MIL and sets a DTC (2 trip detection logic).
  1. Purge flow switching valve is stuck ON (Open)
    In order to depressurize the fuel tank, the pump module's vent valve is turned ON (close) when the purge VSV opens while the vehicle is running. After the fuel tank pressure drops 20 mmHg, the purge VSV closes. Then, the fuel tank pressure rises slightly when the purge flow switching valve is normal. If the pressure rises quickly, the ECM interprets this as a malfunction. The ECM illuminates the MIL and sets a DTC (2 trip detection logic).

MONITOR STRATEGY


Related DTCs
P0466: Purge flow switching valve fixed
Required Sensors/Components
Purge flow switching valve
Frequency of Operation
Once per driving cycle
Duration
Within 10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTC not present
P0441: Purge VSV
P1450 - P1453: FTP sensor
Altitude
Less than 2,400 m (8,000 ft.)
Battery voltage
11 V or more
IAT at engine start - ECT at engine start
-7 to 11°C (-12.6 to 20°F)
ECT at engine start
4.4 to 35°C (40 to 95°F)
IAT at engine start
4.4 to 35°C (40 to 95°F)
Vehicle speed
Constant between 45 and 130 km/h (28 and 80 mph)
Time after engine start
Less than 30 minutes
HV ECU
OK
Fail-safe via HV ECU
Not executed
Purge flow volume
0.08 g/sec. or more

TYPICAL MALFUNCTION THRESHOLDS


Following conditions are met
-
FTP change when purge flow switching valve is ON
0.267 kPa (2 mmHg) or more
FTP
-2.667 kPa (-20 mmHg) or higher
FTP increase after 20 mmHg vacuum is applied to fuel tank
1.333 kPa (10 mmHg) or more

WIRING DIAGRAM


A151912E02


A151893E04


INSPECTION PROCEDURE

1.CONFIRM DTC
  1. Turn the power switch OFF and wait for 10 seconds.

  1. Turn the power switch ON (IG).

  1. Turn the power switch OFF and wait for 10 seconds.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Check if DTC P0446 is output.



NO
Go to step 5
YES


2.PERFORM EVAPORATIVE SYSTEM CHECK
  1. Note the freeze frame data and DTCs.

  1. Clear the DTCs.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

  1. After the system check is finished, check for pending DTCs.

    OK:
    No DTC is present.



NG
Go to step 6
OK


3.CHECK OPERATION OF PURGE FLOW SWITCHING VALVE
  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Tank Bypass.

  1. Touch the purge flow switching valve (TANK BYPASS VSV) to feel the operating vibration.

    OK:
    The purge flow switching valve is operated by the Active Test.



NG
Go to step 18
OK


4.CHECK PURGE FLOW SWITCHING VALVE


    A087973E01
  1. Turn the power switch OFF.

  1. Remove the purge flow switching valve.

  1. Reconnect the purge flow switching valve connector.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Tank Bypass.

  1. Check the airflow for the purge flow switching valve.

    OK:
    The purge flow switching valve operates normally.



NG
Go to step 19

OK
Go to step 33

5.PERFORM EVAPORATIVE SYSTEM CHECK
  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

  1. After the system check is finished, check for pending DTCs.

    OK:
    DTCs are present.



NG
CHECK FOR INTERMITTENT PROBLEMS
OK


6.CHECK DTC
  1. Check the DTCs that were present in the EVAP system check.

OK:
P043E, P043F, P2401, P2402 and P2419 are present.



NG
Go to step 10
OK


7.CHECK VENT VALVE CLOSE STUCK
  1. Allow the engine to idle.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

  1. Turn the EVAP VSV ON (purge VSV open) and check the VAPOR PRESS (EVAP pressure) for 10 seconds.

    OK:
    EVAP pressure is higher than 755 mmHg.



NG
Go to step 20
OK


8.CHECK LEAK DETECTION PUMP OPERATION
  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Vacuum Pump.

  1. Touch the pump module to feel the operating vibration.

    OK:
    The leak detection pump is operated by the Active Test.



NG
Go to step 21
OK


9.CHECK TRAP CANISTER


    A135512
  1. Disconnect the vent hose from the pump module.

  1. Check that no moisture is in the pump module or the vent hose.

    OK:
    No moisture.



OK
Go to step 22

NG
Go to step 23

10.CHECK DTC
  1. Check the DTCs that were present in the EVAP system check.

OK:
P0441, P0455 and/or P0456 are present.



NG
Go to step 16
NG


11.CHECK INSTALLATION CONDITIONS OF FUEL CAP
  1. Remove the fuel cap.

  1. Reinstall the fuel cap.

  1. Clear the DTCs.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

  1. After the system check is finished, check for pending DTCs.

    HINT:
    If no DTC is present, this indicates that the fuel cap is loosened.

    OK:
    No DTC is present.



OK
REPAIR COMPLETED
NG


12.LOCATE LEAK POINT


  1. Disconnect the vent hose (fresh air line) as shown in the illustration.


    A131407E01

  1. Connect the pressure gauge and air pump as shown in the illustration.

  1. Pressurize the EVAP system until the pressure reaches 24 to 28 mmHg.

  1. Locate the leak point.

    HINT:
    If the EVAP system has leakage, a whistling sound may be heard.

    OK:
    The leak point is found.



OK
Go to step 24
NG


13.CHECK FUEL CAP
Check that the fuel cap meets OEM specifications.

HINT:
If an EVAP tester is available, perform the fuel cap test according to the tester's instructions.

OK:
Fuel cap meets OEM specifications.



NG
Go to step 25
OK


14.CHECK OPERATION FOR PURGE VSV
  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

  1. Touch the purge VSV to feel the operating vibration.

    OK:
    The purge VSV (EVAP VSV) is operated by the Active Test.



NG
Go to step 26
OK


15.CHECK INTAKE MANIFOLD PRESSURE


    A130450E01
  1. Disconnect the purge VSV hose that is connected to the throttle body.

  1. Allow the engine to idle.

  1. Check that the hose has suction using your finger.

    OK:
    The hose has suction.



NG
Go to step 27

OK
Go to step 28

16.CHECK DTC
  1. Check the DTCs that were present in the EVAP system check.

OK:
P0451 is not present.



NG
Go to step 9
OK


17.CHECK OPERATION FOR VENT VALVE
  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Vent Valve.

  1. Touch the pump module to feel the operating vibration.

    OK:
    The vent valve is operated by the Active Test.



OK
Go to step 9

NG
Go to step 29

18.CHECK HARNESS AND CONNECTOR (PURGE FLOW SWITCHING VALVE - ECM AND EFI M RELAY)


    A072890E08
  1. Check the harness and the connectors between the purge flow switching valve and the ECM.

    1. Disconnect the V8 purge flow switching valve connector.



    2. A065744E70
    3. Disconnect the E7 ECM connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      V8-1 (Purge flow switching valve) - E7-18 (TBP)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      V8-1 (Purge flow switching valve) or E7-18 (TBP) - Body ground
      10 kΩ or higher

    5. Reconnect the purge flow switching valve connector.

    6. Reconnect the ECM connector.



  1. Check the harness and the connectors between the purge flow switching valve and the EFI M relay.

    1. Disconnect the V8 purge flow switching valve connector.



    2. A082810E01
    3. Remove the integration relay from the engine room relay block.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      V8-2 (Purge flow switching valve) - 3I-8 (EFI M relay)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      V8-2 (Purge flow switching valve) or 3I-8 (EFI M relay) - Body ground
      10 kΩ or higher

    5. Reconnect the purge flow switching valve connector.

    6. Reinstall the integration relay.



NG
Go to step 30

OK
Go to step 31

19.REPLACE PURGE FLOW SWITCHING VALVE
Replace the purge flow switching valve.


NEXT
Go to step 34

20.CHECK FOR VENT HOSE CLOG
  1. Turn the power switch OFF.



    A135512
  1. Disconnect the vent hose (fresh air line) as shown in the illustration.

  1. Allow the engine to idle.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

  1. Turn the purge VSV (EVAP VSV) ON and check the EVAP pressure (VAPOR PRESS) for 10 seconds.

    OK:
    EVAP pressure is higher than 755 mmHg.



NG
Go to step 22

OK
Go to step 32

21.CHECK HARNESS AND CONNECTOR (LEAK DETECTION PUMP - ECM)


    A085258E76
  1. Disconnect the V7 canister pump module connector.



    A065744E71
  1. Disconnect the E7 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    V7-1 (MTRB) - E7-13 (MPMP)
    Below 1 Ω
    V7-6 (MGND) - Body ground
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    V7-1 (MTRB) or E7-13 (MPMP) - Body ground
    10 kΩ or higher

  1. Reconnect the canister pump module connector.

  1. Reconnect the ECM connector.



NG
Go to step 30

OK
Go to step 31

22.REPLACE TRAP CANISTER WITH PUMP MODULE
Replace the trap canister with pump module (Click here).


NEXT
Go to step 34

23.CHECK FOR VENT HOSE DAMAGE
Check for hose damage as shown in the illustration. If necessary, replace the vent hose.

A130304E01



NEXT
Go to step 22

24.REPAIR OR REPLACE LEAK POINT


NEXT
Go to step 34

25.REPLACE FUEL CAP


NEXT
Go to step 34

26.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)


    A052933E24
  1. Disconnect the V1 purge VSV connector.



    A065745E73
  1. Disconnect the E5 ECM connector.

  1. Check the harness and the connectors between the ECM and the purge VSV connectors.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      V1-1 - E5-14 (EVP1)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      V1-1 or E5-14 (EVP1) - Body ground
      10 kΩ or higher



    A082810E01
  1. Remove the integration relay from the engine room relay block.

  1. Check the harness and connectors between the purge VSV connector and the EFI M relay.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      V1-2 - 3I-8 (EFI M relay)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      V1-2 or 3I-8 (EFI M relay) - Body ground
      10 kΩ or higher

  1. Reconnect the purge VSV connector.

  1. Reconnect the ECM connector.

  1. Reinstall the integration relay.



NG
Go to step 30

OK
Go to step 31

27.REPLACE HOSE (PURGE VSV - THROTTLE BODY)


NEXT
Go to step 34

28.REPLACE PURGE VSV
Replace the purge VSV.


NEXT
Go to step 34

29.CHECK HARNESS AND CONNECTOR (VENT VALVE - ECM)


    A085258E77
  1. Disconnect the V7 canister pump module connector.



    A065744E72
  1. Disconnect the E7 ECM connector.

  1. Check the harness and the connectors between the ECM and the canister connectors.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      V7-8 (VGND) - E7-26 (VPMP)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      V7-8 (VGND) or E7-26 (VPMP) - Body ground
      10 kΩ or higher



    A082810E01
  1. Remove the integration relay from the engine room relay block.

  1. Check the harness and connectors between the canister connector and the EFI M relay.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      V7-9 (VLVB) - 3I-8 (EFI M relay)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      V7-9 (VLVB) or 3I-8 (EFI M relay) - Body ground
      10 kΩ or higher

  1. Reconnect the canister pump module connector.

  1. Reconnect the ECM connector.

  1. Reinstall the integration relay.



NG
Go to step 30

OK
Go to step 31

30.REPAIR OR REPLACE HARNESS OR CONNECTOR


NEXT
Go to step 34

31.REPLACE ECM
Replace the ECM (Click here).


NEXT
Go to step 34

32.CHECK AND REPLACE VENT HOSE OR CANISTER FILTER


NEXT
Go to step 34

33.REPLACE HOSE (PURGE FLOW SWITCHING VALVE AND FUEL TANK)

NEXT


34.PERFORM EVAPORATIVE SYSTEM CHECK
  1. Turn the power switch ON (IG).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

  1. After the system check is finished, check for pending DTCs.

    OK:
    No DTC is present.



NG
Go to step 6
OK


35.PERFORM EVAP MONITOR DRIVE PATTERN
  1. Check that the following conditions are met:

    1. Fuel level is 1/8 to 7/8.
    2. Engine coolant temperature (ECT) is 4.4 to 35°C (40 to 95°F).
    3. Intake air temperature (IAT) is 4.4 to 35°C (40 to 95°F).
    4. Difference between ECT and IAT is less than 7°C (13°F).

  1. Enter the check mode. Enter the following menus: Powertrain / Engine and ECT / Utility / Check Mode.

  1. Allow the engine to idle until the ECT is 75°C (167°F).

  1. Drive the vehicle at 50 km/h (30 mph) or faster and maintain that speed for 60 seconds or more.

  1. Stop the vehicle. Do not turn the power switch OFF.

  1. Check that the EVAP monitor status is complete. Enter the following menus: Powertrain / Engine and ECT / Monitor / Evaporative System.

  1. If the EVAP monitor is incomplete, drive the vehicle at 50 km/h (30 mph) or faster and maintain that speed for 120 seconds or more. After that, recheck the EVAP monitor status.

  1. Check for pending DTCs.

    OK:
    No DTC is present.



NG
Go to step 2
OK

REPAIR COMPLETED