Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

for Preparation Click here

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DESCRIPTION

These DTCs are set when there is an open or short in the A/F sensor circuit, or if A/F sensor output drops. To detect these problems, the voltage of the A/F sensor is monitored when the power switch is turned ON (IG), and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the A/F sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the A/F sensor. If the same malfunction is detected in the next driving cycle, the MIL will be illuminated and a DTC will be stored.
The A/F sensor, which is located between the exhaust manifold and catalyst, consists of alloyed metal elements and a heater.
Depending on the engine operating conditions, the heater heats the sensor elements to activate them. Battery voltage is applied to the heater, the sensor ground is controlled by the ECM using a duty ratio.
The sensor elements convert the oxygen concentration in the exhaust gas into voltage values to output. Based on the voltage, the ECM determines the air-fuel ratio and regulates the fuel injection volume depending on the air-fuel ratio and engine operating conditions. The voltage changes between 0.6 V and 4.5 V while the engine is running. If the air-fuel ratio is LEAN, which means the oxygen concentration in the exhaust gas is high, the voltage is high. If the air-fuel ratio is RICH, which means the oxygen concentration in the exhaust gas is low, the voltage is low.

B062793E17


A107164E12


DTC No.
DTC Detection Condition
Trouble Area
P2237
Open in the circuit between terminals AF+ and AF- of the AF sensor while engine is running
(2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2238
Any of the following conditions are met
(2 trip detection logic)
  1. AF sensor output drops while engine is running.
  1. Voltage at terminal AF+ is 0.5 V or less.
  1. Voltage difference between terminals AF+ and AF- is 0.1 V or less.
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2239
AF+ voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2252
AF- voltage 0.5 V or less
(2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2253
AF- voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in A/F sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM

MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the A/F sensor circuit, or if A/F sensor output drops. To detect these problems, the voltage of the A/F sensor is monitored when the power switch ON (IG), and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the A/F sensor is between 0.5 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the A/F sensor. If the same malfunction is detected in the next driving cycle, the MIL will be illuminated and a DTC will be stored.

MONITOR STRATEGY


Related DTCs
P2237: A/F sensor open circuit between AF+ and AF-
P2238: A/F sensor short circuit between AF+ and AF-
P2238: A/F sensor short circuit between AF+ and GND
P2238: A/F sensor admittance low
P2239: A/F sensor short circuit between AF+ and +B
P2252: A/F sensor short circuit between AF- and GND
P2253: A/F sensor short circuit between AF- and +B
Required Sensors/Components (Main)
A/F sensor
Required Sensors/Components (Related)
Engine Coolant Temperature (ECT) sensor, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Within 10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
P0031, P0032 (A/F sensor heater - Sensor 1)
P0100 - P0103 (MAF meter)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)
P0120 - P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for Closed Loop)
P0171, P0172 (Fuel trim)
P0300 - P0304 (Misfire)
P0335 (CKP sensor)
P0340 (CMP sensor)
P0441 - P0456, P2401 - P2420 (EVAP system)
P0500 (VSS)

P2237: (A/F sensor open circuit between AF+ and AF-) 
Estimated sensor temperature
450 to 550°C (842 to 1,022°F)
Engine
Running
Battery voltage
11 V or more

P2238: (A/F sensor admittance low) 
Estimated sensor temperature
700 to 800°C (1,292 to 1,472°F)
ECT
10°C (50°F) or more (Closed loop enabling ECT)
Fuel-cut
Not executed

Except P2237 (A/F sensor open circuit between AF+ and AF-) and P2238 (A/F sensor admittance low) 
Battery voltage
11 V or more
Power switch
ON
Time after power switch is turned OFF to ON (IG)
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P2237: (A/F sensor open circuit between AF+ and AF-) 
A/F sensor admittance
Below 0.002 1/Ω

P2238: (A/F sensor admittance low) 
A/F sensor admittance
Below 0.015 1/Ω

P2238: (A/F sensor short circuit between AF+ and AF-) 
Difference between AF+ and AF- terminal voltages
0.1 V or less

P2238: (A/F sensor short circuit between AF+ and GND) 
AF+ terminal voltage
0.5 V or less

P2239: (A/F sensor short circuit between AF+ and +B) 
AF+ terminal voltage
More than 4.5 V

P2252: (A/F sensor short circuit between AF- and GND) 
AF- terminal voltage
0.5 V or less

P2253: (A/F sensor short circuit between AF- and +B) 
AF- terminal voltage
More than 4.5 V

COMPONENT OPERATING RANGE


A/F sensor admittance
0.022 1/Ω or more
AF+ terminal voltage
0.6 to 4.5 V
AF- terminal voltage
0.6 to 4.5 V
Difference between AF+ and AF- terminal voltages
0.1 to 0.8 V

WIRING DIAGRAM


A151895E04


INSPECTION PROCEDURE

HINT:
Techstream only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using Techstream.
  1. Connect Techstream to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
  4. On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
  5. Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5 % or increases the injection volume by 25 %.
  1. The sensors react in accordance with increases and decreases in the fuel injection volume.


Standard:

Tester Display
(Sensor)
Injection Volume
Status
Voltages
AFS B1 S1
(A/F)
+25 %
Rich
Less than 3.0
-12.5 %
Lean
More than 3.35
O2S B1 S2
(HO2)
+25 %
Rich
More than 0.5
-12.5 %
Lean
Less than 0.4

NOTICE:
The A/F sensor has an output delay of a few seconds and the HO2 sensor has a maximum output delay of approximately 20 seconds.


Case
A/F Sensor (Sensor 1)
Output Voltage
HO2 Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
A150444E03
A150447E02
A150444E03
A150446E02
-
2
A150444E03
A150445E02
A150444E03
A150446E02
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150444E03
A150447E02
A150444E03
A150445E02
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150444E03
A150445E02
A150444E03
A150445E02
  1. Fuel pressure
  2. Gas leakage from exhaust system
    (Air-fuel ratio extremely lean or rich)
  1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the output voltages of both the A/F and HO2 sensors.
  2. To display the graph, select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2 then press the graph button on the Data List view.

HINT:
Read freeze frame data using Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)


    A085153E07
  1. Disconnect the A5 A/F sensor connector.



    A065745E71
  1. Disconnect the E5 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    A5-3 (AF+) - E5-23 (A1A+)
    Below 1 Ω
    A5-4 (AF-) - E5-22 (A1A-)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    A5-3 (AF+) or E5-23 (A1A+) - Body ground
    10 kΩ or higher
    A5-4 (AF-) or E5-22 (A1A-) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.



  1. Reconnect the A/F sensor connector.


    B062793E17



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE AIR-FUEL RATIO SENSOR

NEXT


3.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 5 minutes or more.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code / Pending.

  1. Read the pending DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2237, P2238, P2239, P2252 or P2253
    B



B
REPLACE ECM
A

END