Home › Vehicle Exterior › BODY PANEL › FRONT FENDER APRON
BM2170E _01 Vehicle Exterior _057059 BODY WELD POINT _0278238 FRONT FENDER APRON F

BODY WELD POINT  FRONT FENDER APRON  ASSEMBLY REPLACEMENT  


K104254

With the cowl top side panel removed.


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108820

Remove Weld Points


U159822E02
0.25,0.125 0.635,0.479 0.385,0.354 12 false LH: 1.427,2.792 1.531,2.948 0.104,0.156 10 false 2 3.458,4.75 3.563,4.906 0.104,0.156 10 false 6 5.917,5.573 6.021,5.729 0.104,0.156 10 false 3 6.448,6.656 6.552,6.813 0.104,0.156 10 false 1 6.583,7.396 6.688,7.552 0.104,0.156 10 false 7 1.927,4.771 2.031,4.927 0.104,0.156 10 false 6 4.927,2.583 5.021,2.74 0.094,0.156 10 false 4 3.396,1.365 3.49,1.521 0.094,0.156 10 false 1 2.698,4.75 2.875,4.906 0.177,0.156 10 false 10

U159823E02
0.24,0.115 0.615,0.469 0.375,0.354 12 false RH: 0.896,3.115 1,3.271 0.104,0.156 10 false 6 2.604,4.521 2.708,4.677 0.104,0.156 10 false 9 3.323,4.51 3.427,4.667 0.104,0.156 10 false 5 4.167,4.479 4.271,4.635 0.104,0.156 10 false 3 5.25,3.229 5.354,3.385 0.104,0.156 10 false 2 4.646,2.583 4.75,2.74 0.104,0.156 10 false 1 4.229,2.24 4.333,2.396 0.104,0.156 10 false 3 3.771,5.344 3.875,5.5 0.104,0.156 10 false 3 3.313,6.427 3.417,6.583 0.104,0.156 10 false 1 3.167,7.156 3.271,7.313 0.104,0.156 10 false 7 2.563,1.125 2.656,1.281 0.094,0.156 10 false 1 0.875,2.115 0.969,2.271 0.094,0.156 10 false 4

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108825

Plug Weld


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram)

3.

Make sure to attach correctly in accordance with the body dimension diagram as this part affects the front wheel alignment.

4.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

5.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K135713E01
2.146,5.458 1.979,5.458 1.979,5.458 2.333,3.76 false 0.229,0.115 0.552,0.375 0.323,0.26 12 false LH: 2.188,5.365 4.927,5.594 2.74,0.229 10 false FRONT FENDER APRON SUB-ASSEMBLY

K135714E01
2.75,5.156 2.635,5.156 2.635,5.156 2.969,3.5 false 0.26,0.198 0.625,0.469 0.365,0.271 12 false RH: 2.802,5.063 5.573,5.281 2.771,0.219 10 false FRONT FENDER APRON SUB-ASSEMBLY