2011-2020 Prius C Service Manual
1NZ-FXE
Trouble codes (1731)
- P0010Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic).
- P0011Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
- P0012Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
- P0016Deviation in crank position sensor signal and cam position sensor signal (2 trip detection logic).
- P0031Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater output...
- P0032Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
- P0037Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip...
- P0038Heated oxygen sensor heater current reaches high limit (1 trip detection logic).
- P00FELeak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured....
- P0101All of the following conditions continue (2 trip detection logic). (a) The engine is running. (b) The engine...
- P0102The mass air flow meter sub-assembly voltage is less than 0.2 V for 3 seconds. (1 trip detection logic:...
- P0103The mass air flow meter sub-assembly voltage is higher than 4.9 V for 3 seconds. (1 trip detection logic:...
- P0106Intake manifold pressure measured after engine start drops by less than 3 kPa [22.5 mmHg] compared to the...
- P0107The output voltage from the manifold absolute pressure sensor less than 0.5 V for 0.5 seconds (1 trip...
- P0108The output voltage from the manifold absolute pressure sensor higher than 4.5 V for 0.5 seconds (1 trip...
- P0111Either of the following condition is met (2 trip detection logic). · The intake air temperature change from...
- P0112A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0113An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0115An open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0116When either of the following conditions is met (2 trip detection logic). · During engine warm up after cold...
- P0117A short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0118An open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P011BAll of the following conditions are met (2 trip detection logic): (a) The auxiliary battery voltage is 10.5 V...
- P0120The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0121The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1...
- P0122The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic).
- P0123The output voltage of VTA1 is 4.535 V or higher for 2 seconds or more (1 trip detection logic).
- P0125The engine coolant temperature does not reach the closed loop enabling temperature for 20 minutes (this...
- P0128All of the following conditions are met for 5 seconds (2 trip detection logic): (a) Cold start. (b) The...
- P0136Either of the following conditions is met: · Abnormal voltage output: During active air fuel ratio control,...
- P0137Either of the following conditions is met: · Low voltage (open): During active air fuel ratio control,...
- P0138· Extremely high voltage (short): Heated oxygen sensor voltage output exceeds 1.2 V for 10 seconds or more (2...
- P0139Heated oxygen sensor (sensor 2) voltage does not drop to less than 0.2 V immediately after fuel cut starts (2...
- P013AHeated oxygen sensor (sensor 2) voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut status...
- P0141The cumulative heater resistance correction value exceeds the threshold (2 trip detection logic).
- P014CThe "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
- P014DThe "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
- P015AThe "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
- P015BThe "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
- P0171With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0172With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0220The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0222The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic).
- P0223The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0327The output voltage of the knock control sensor is less than 0.5 V for 1 second or more (1 trip detection...
- P0328The output voltage of the knock control sensor is higher than 4.5 V for 1 second or more (1 trip detection...
- P0335Either of the following conditions is met (1 trip detection logic): · No crank position sensor signal to ECM...
- P0340Either of the following conditions is met (1 trip detection logic): · No cam position sensor signal to the...
- P0351No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0352No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0353No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0354No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0401Change in intake manifold pressure is small when the EGR valve is opened and closed during fuel cut operation...
- P0403Open or short in EGR valve circuit (1 trip detection logic).
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (1 trip...
- P043E, P043F, P2401, P2402 and P2419 stored when one of following conditions met during key-off EVAP monitor:...
- P043E, P043F, P2401, P2402 and P2419 stored when one of following conditions met during key-off EVAP monitor:...
- P043FP043F
- P043FP043F
- P0441Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0441Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0451Sensor output voltage fluctuates frequently in a certain time period.
- P0451Sensor output voltage fluctuates frequently in a certain time period.
- P0452EVAP pressure sensor less than 0.45 V for 0.5 seconds.
- P0452EVAP pressure sensor less than 42.11009 kPa(abs) [315.82568 mmHg(abs)] for 0.5 seconds.
- P0453EVAP pressure sensor higher than 123.76147 kPa(abs) [928.21103 mmHg(abs)] for 0.5 seconds.
- P0453EVAP pressure sensor higher than 4.9 V for 0.5 seconds.
- P0455Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured....
- P0455Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured....
- P0456Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured....
- P0456Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured....
- P0461The change in the fuel sender gauge value is below the threshold when a certain amount of fuel is calculated...
- P0462Fuel sender gauge output resistance is below 7 Ω for 30 seconds or more (1 trip detection logic).
- P0463Fuel sender gauge output resistance is higher than 480 Ω for 30 seconds or more (2 trip detection logic).
- P0505Idle speed continues to vary greatly from the target idle speed (2 trip detection logic).
- P050AInsufficient mass air flow after a cold start (2 trip detection logic).
- P050AInsufficient mass air flow after a cold start (2 trip detection logic).
- P050BInsufficient ignition timing retard at cold start (2 trip detection logic).
- P0560An open in the ECM back up power source circuit (1 trip detection logic).
- P0604ECM RAM error (1 trip detection logic).
- P0606An ECM main CPU error (1 trip detection logic).
- P0607· The ECM CPUs malfunction. · The heated oxygen sensor transistor (built into the ECM) malfunctions.
- P060AA CPU reset is performed after one of the following conditions is met (1 trip detection logic): · There is an...
- P060BAn ECM main CPU communication error (1 trip detection logic).
- P060EEither of the following condition is met (1 trip detection logic): · There is an ECM main CPU error. · There...
- P062FAn ECM internal error (EEPROM) (1 trip detection logic).
- P0630When either of the following conditions is met (1 trip detection logic). · The VIN is not stored in the ECM....
- P0657A throttle actuator power supply error (1 trip detection logic).
- P101DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P102DHeated oxygen sensor heater current is higher than the specified value while the heater is not operating (1...
- P106AThe difference between the pressure of the canister pressure sensor (Vapor Pressure Pump*) and manifold...
- P148FWhen both of the following conditions are met for 5 seconds or more (1 trip detection logic): · Engine water...
- P1604Either of the conditions is met (1 trip detection logic): · The engine speed is less than 500 rpm with the...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P2102Both of the following conditions continue for 2.0 seconds (1 trip detection logic): (a) The throttle actuator...
- P2103Either of the following conditions is met (1 trip detection logic): · A motor driver IC high current limiter...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
- P2112The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
- P2118An open in the electronic throttle control system power source (+BM) circuit (1 trip detection logic).
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection...
- P2135Either of the following conditions is met (1 trip detection logic): (a) The difference between the output...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P219AThe difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
- P219CThe difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
- P219DThe difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
- P219EThe difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
- P219FThe difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
- P2237An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is...
- P2238· Case 1 Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2239· Case 1 The A1A+ voltage is higher than 4.5 V (2 trip detection logic). · Case 2 Voltage difference between...
- P2252The A1A- voltage is 0.5 V or less (2 trip detection logic).
- P2253The A1A- voltage is higher than 4.5 V (2 trip detection logic).
- P2401P2401
- P2401P2401
- P2402P2402
- P2402P2402
- P2419P2419
- P2419P2419
- P2420Following condition met during key-off EVAP monitor: · EVAP pressure change when vent valve closed (on) less...
- P2420Following condition met during key-off EVAP monitor: · EVAP pressure change when vent valve closed (on) less...
- P2610ECM internal malfunction (2 trip detection logic)
- P261BEngine water pump assembly speed is less than 900 rpm while the engine water pump assembly is operating (1...
- P261CEngine water pump assembly output voltage is less than specified value while the engine water pump assembly...
- P261DEngine water pump assembly output voltage is higher than specified value while the engine water pump assembly...
- P3190When all of the following conditions are met (1 trip detection logic): · Engine speed is 650 rpm or higher...
- P3191When all of the following conditions are met (1 trip detection logic): · Engine speed is 650 rpm or higher...
- P3193All of the following conditions are met (1 trip detection logic): · Power switch on (IG). · The ECM receives...
- U0155All of the following conditions are met for 2.6 seconds or more (1 trip detection logic). · Power switch on...
- U0293Communication with hybrid vehicle control ECU is interrupted (1 trip detection logic).
- P0010Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic).
- P0011Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
- P0011Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
- P0011Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
- P0012Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
- P0012Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
- P0012Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
- P0016Deviation in crank position sensor signal and cam position sensor signal (2 trip detection logic).
- P0016Deviation in crank position sensor signal and cam position sensor signal (2 trip detection logic).
- P0016Deviation in crank position sensor signal and cam position sensor signal (2 trip detection logic).
- P0031Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater output...
- P0031Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater output...
- P0031Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater output...
- P0032Air fuel ratio sensor heater current reaches the high limit. (Hybrid IC high current limiter monitor input...
- P0032Air fuel ratio sensor heater current reaches the high limit. (Hybrid IC high current limiter monitor input...
- P0032Air fuel ratio sensor heater current reaches the high limit. (Hybrid IC high current limiter monitor input...
- P0037Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip...
- P0037Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip...
- P0037Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip...
- P0038Heated oxygen sensor heater current reaches high limit. (Hybrid IC high current limiter monitor input "Fail")...
- P0038Heated oxygen sensor heater current reaches high limit. (Hybrid IC high current limiter monitor input "Fail")...
- P0038Heated oxygen sensor heater current reaches high limit. (Hybrid IC high current limiter monitor input "Fail")...
- P0102The mass air flow meter sub-assembly voltage is less than 0.2 V for 3 seconds (1 trip detection logic).
- P0103The mass air flow meter sub-assembly voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
- P0107The output voltage from the manifold absolute pressure sensor less than 0.5 V for 0.5 seconds (1 trip...
- P0108The output voltage from the manifold absolute pressure sensor higher than 4.5 V for 0.5 seconds (1 trip...
- P0112A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0113An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0115An open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0116When either of the following conditions is met (2 trip detection logic). · During engine warm up after cold...
- P0116When either of the following conditions is met (2 trip detection logic). · During engine warm up after cold...
- P0116When either of the following conditions is met (2 trip detection logic). · During engine warm up after cold...
- P0117A short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0118An open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0120The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0121The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1...
- P0122The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic).
- P0123The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1 trip detection logic).
- P0136Abnormal voltage output: During active air fuel ratio control, the following conditions (a) and (b) are met...
- P0136Abnormal voltage output: During active air fuel ratio control, the following conditions (a) and (b) are met...
- P0136Abnormal voltage output: During active air fuel ratio control, the following conditions (a) and (b) are met...
- P0137Low voltage (open): During active air fuel ratio control, the following conditions (a) and (b) are met for a...
- P0137Low voltage (open): During active air fuel ratio control, the following conditions (a) and (b) are met for a...
- P0137Low voltage (open): During active air fuel ratio control, the following conditions (a) and (b) are met for a...
- P0138High voltage (short): During active air fuel ratio control, the following conditions (a) and (b) are met for...
- P0138High voltage (short): During active air fuel ratio control, the following conditions (a) and (b) are met for...
- P0138High voltage (short): During active air fuel ratio control, the following conditions (a) and (b) are met for...
- P0171With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0171With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0171With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean...
- P0172With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0172With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0172With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich...
- P0220The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0222The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic).
- P0223The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip...
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0301Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0302Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0303Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0304Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic)....
- P0327The output voltage of the knock control sensor is less than 0.5 V for 1 second or more (1 trip detection...
- P0328The output voltage of the knock control sensor is higher than 4.5 V for 1 second or more (1 trip detection...
- P0335Either of the following conditions is met (1 trip detection logic): · No crank position sensor signal to ECM...
- P0340Either of the following conditions is met (1 trip detection logic): · No cam position sensor signal to the...
- P0351No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0351No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0351No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0352No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0352No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0352No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0353No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0353No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0353No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0354No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0354No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0354No IGF signal to the ECM while the engine is running (1 trip detection logic).
- P0401Change in intake manifold pressure is small when the EGR valve is opened and closed during idle fuel cut...
- P0401Change in intake manifold pressure is small when the EGR valve is opened and closed during idle fuel cut...
- P0401Change in intake manifold pressure is small when the EGR valve is opened and closed during idle fuel cut...
- P0403Open or short in EGR valve circuit (1 trip detection logic).
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip...
- P0443Both of the following conditions (a) and (b) are met (1 trip detection logic): (a) The target control value...
- P0443Both of the following conditions (a) and (b) are met (1 trip detection logic): (a) The target control value...
- P0560An open in the ECM back up power source circuit (1 trip detection logic).
- P0560An open in the ECM back up power source circuit (1 trip detection logic).
- P0560An open in the ECM back up power source circuit (1 trip detection logic).
- P0604ECM RAM error (1 trip detection logic).
- P0604ECM RAM error (1 trip detection logic).
- P0604ECM RAM error (1 trip detection logic).
- P0606An ECM main CPU error (1 trip detection logic).
- P0606An ECM main CPU error (1 trip detection logic).
- P0606An ECM main CPU error (1 trip detection logic).
- P060AA CPU reset is performed after one of the following conditions is met (1 trip detection logic): · There is an...
- P060AA CPU reset is performed after one of the following conditions is met (1 trip detection logic): · There is an...
- P060AA CPU reset is performed after one of the following conditions is met (1 trip detection logic): · There is an...
- P060BAn ECM main CPU communication error (1 trip detection logic).
- P060BAn ECM main CPU communication error (1 trip detection logic).
- P060BAn ECM main CPU communication error (1 trip detection logic).
- P060EEither of the following condition is met (1 trip detection logic): · There is an ECM main CPU error. · There...
- P060EEither of the following condition is met (1 trip detection logic): · There is an ECM main CPU error. · There...
- P060EEither of the following condition is met (1 trip detection logic): · There is an ECM main CPU error. · There...
- P0630Either of the following conditions is met (1 trip detection logic): · The VIN or frame number is not stored...
- P0657A throttle actuator power supply error (1 trip detection logic).
- P0657A throttle actuator power supply error (1 trip detection logic).
- P0657A throttle actuator power supply error (1 trip detection logic).
- P101DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P101DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P101DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P102DHeated oxygen sensor heater current is higher than the specified value while the heater is not operating (1...
- P102DHeated oxygen sensor heater current is higher than the specified value while the heater is not operating (1...
- P102DHeated oxygen sensor heater current is higher than the specified value while the heater is not operating (1...
- P148FWhen both of the following conditions are met for 5 seconds or more (1 trip detection logic): · Engine water...
- P148FWhen both of the following conditions are met for 5 seconds or more (1 trip detection logic): · Engine water...
- P148FWhen both of the following conditions are met for 5 seconds or more (1 trip detection logic): · Engine water...
- P1604Either of the conditions is met (1 trip detection logic): · The engine speed is less than 500 rpm with the...
- P1604Either of the conditions is met (1 trip detection logic): · The engine speed is less than 500 rpm with the...
- P1604Either of the conditions is met (1 trip detection logic): · The engine speed is less than 500 rpm with the...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P2102Both of the following conditions continue for 2.0 seconds (1 trip detection logic): (a) The throttle actuator...
- P2103Either of the following conditions is met (1 trip detection logic): · A hybrid IC diagnosis signal failure. ·...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
- P2111The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
- P2111The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
- P2112The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
- P2112The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
- P2112The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
- P2118An open in the electronic throttle control system power source (+BM) circuit (1 trip detection logic).
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection...
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection...
- P2119The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection...
- P2135Either of the following conditions is met (1 trip detection logic): (a) The difference between the output...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2237An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is...
- P2237An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is...
- P2237An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is...
- P2238· Case 1 Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2238· Case 1 Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2238· Case 1 Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) Voltage at...
- P2239The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
- P2239The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
- P2239The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
- P2252The A1A- voltage is 0.5 V or less (2 trip detection logic).
- P2252The A1A- voltage is 0.5 V or less (2 trip detection logic).
- P2252The A1A- voltage is 0.5 V or less (2 trip detection logic).
- P2253The A1A- voltage is higher than 4.5 V (2 trip detection logic).
- P2253The A1A- voltage is higher than 4.5 V (2 trip detection logic).
- P2253The A1A- voltage is higher than 4.5 V (2 trip detection logic).
- P2610ECM internal malfunction (2 trip detection logic).
- P2610ECM internal malfunction (2 trip detection logic).
- P2610ECM internal malfunction (2 trip detection logic).
- P261BEngine water pump assembly speed is less than 900 rpm while the engine water pump assembly is operating (1...
- P261CEngine water pump assembly output voltage is less than specified value while the engine water pump assembly...
- P261DEngine water pump assembly output voltage is higher than specified value while the engine water pump assembly...
- P2A00The calculated value for the air fuel ratio sensor response rate deterioration level is less than the...
- P2A00The calculated value for the air fuel ratio sensor response rate deterioration level is less than the...
- P2A00The calculated value for the air fuel ratio sensor response rate deterioration level is less than the...
- P2A00The calculated value for the air fuel ratio sensor response rate deterioration level is less than the...
- P3190Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic): ·...
- P3190Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic): ·...
- P3190Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic): ·...
- P3191Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic): ·...
- P3191Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic): ·...
- P3191Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic): ·...
- P3193Fuel low level signal input into ECM (1 trip detection logic).
- P3193Fuel low level signal input into ECM (1 trip detection logic).
- P3193Fuel low level signal input into ECM (1 trip detection logic).
- U0293Communication with hybrid vehicle control ECU is interrupted (1 trip detection logic).
- U0293Communication with power management control ECU is interrupted (1 trip detection logic).
- P0069273 Difference between the atmospheric pressure value of the atmospheric pressure sensor in the inverter with...
- P0069273 Difference between the atmospheric pressure value of the atmospheric pressure sensor in the inverter with...
- P0069273 Difference between the atmospheric pressure value of the atmospheric pressure sensor in the inverter with...
- P0069273 Difference between the atmospheric pressure value of the atmospheric pressure sensor in the inverter with...
- P0343747 GI signal is not input for 2 sec. or more while the engine is running.
- P0343747 GI signal is not input for 2 sec. or more while the engine is running.
- P0343747 GI signal is not input for 2 sec. or more while the engine is running.
- P0343747 GI signal is not input for 2 sec. or more while the engine is running.
- P0516769 Malfunction in the battery thermometer sensor circuit (short to GND)
- P0516769 Malfunction in the battery thermometer sensor circuit (short to GND)
- P0517770 Malfunction in the battery thermometer sensor circuit (open or short to +B)
- P0517770 Malfunction in the battery thermometer sensor circuit (open or short to +B)
- P0560117 Malfunction in the hybrid vehicle control ECU back-up power source circuit (1 trip detection logic)
- P060B134 ECU internal error
- P060B134 ECU internal error
- P0617142 An ST signal from the hybrid vehicle control ECU is on when the power switch is off. (2 trip detection logic)
- P062F143
- P062F143
- P062F489 ECU internal malfunction (1 trip detection logic)
- P06A4209 VC power-supply voltage is lower than 4.2 V
- P06A5210 VC power-supply voltage is higher than 5.8 V
- P06B0163 MG ECU internal malfunction IPM positive power source error (1 trip detection logic)
- P06D6511 MG ECU internal malfunction Standard voltage for analog signal offset (+2.5 V) error (1 trip detection logic)
- P06E6164 MG ECU internal malfunction IPM negative power source error (1 trip detection logic)
- P0705757 Logical inconsistency in shift sensor output values
- P0705757 Logical inconsistency in shift sensor output values
- P0A01726 Abnormal deviation in inverter coolant temperature sensor output. Both of the following conditions are met...
- P0A01726 Abnormal deviation in inverter coolant temperature sensor output. Both of the following conditions are met...
- P0A01726 w/o Canister Pump Module: Abnormal deviation in inverter coolant temperature sensor output. Both of the...
- P0A02719 Short to GND in the HV coolant temperature sensor circuit
- P0A02719 Short to GND in the HV coolant temperature sensor circuit
- P0A03720 Open or short to +B in the HV coolant temperature sensor circuit
- P0A03720 Open or short to +B in the HV coolant temperature sensor circuit
- P0A04725 Sudden change in HV coolant temperature sensor output or hunting: Unusual sudden change in HV coolant...
- P0A04725 Sudden change in HV coolant temperature sensor output or hunting: Unusual sudden change in HV coolant...
- P0A04725 Sudden change in HV coolant temperature sensor output or hunting: Unusual sudden change in HV coolant...
- P0A08264 DC/DC converter malfunction or the auxiliary battery voltage drops to 11 V or less with the power switch on...
- P0A08264 The DC/DC converter is malfunctioning (charging has stopped) and the auxiliary battery voltage drops to 11 V...
- P0A09265 Open or GND short in NODD signal circuit of DC/DC converter
- P0A09265 Open or GND short in NODD signal circuit of DC/DC converter
- P0A09591 DC/DC converter voltage switching (VLO) signal circuit malfunction (Open or short to GND)
- P0A09591 DC/DC converter voltage switching (VLO) signal circuit malfunction (Open or short to GND)
- P0A0D350 Operating any of the safety devices with the vehicle stopped (ILK signal is ON) and turning the power switch...
- P0A0D350 Operating any of the safety devices with the vehicle stopped (ILK signal is ON) and turning the power switch...
- P0A0F204 Signal indicating abnormality input from the ECM (abnormal engine output)
- P0A0F204 Signal indicating abnormality input from the ECM (abnormal engine output)
- P0A0F204 Signal indicating abnormality input from the ECM (abnormal engine output)
- P0A0F204 Signal indicating abnormality input from the ECM (abnormal engine output)
- P0A0F238 Engine does not start even though it is being cranked (transaxle input malfunction [engine system])
- P0A0F238 Engine does not start even though it is being cranked (transaxle input malfunction [engine system])
- P0A10263 Short to +B in the DC/DC converter NODD signal line
- P0A10263 Short to +B in the DC/DC converter NODD signal line
- P0A10592 DC/DC converter voltage switching (VLO) signal circuit malfunction (short to +B)
- P0A10592 DC/DC converter voltage switching (VLO) signal circuit malfunction (short to +B)
- P0A1A151 MG ECU internal malfunction Run pulse signal cycle deviation or stop (1 trip detection logic)
- P0A1A151 Run pulse signal cycle deviation or stop
- P0A1A200 The difference between the resolver angle for control and estimated resolver angle exceeds the allowable...
- P0A1A517 Generator inverter fail signal detection (overcurrent due to MG ECU malfunction)
- P0A1B163 IPM positive power source error
- P0A1B168 The difference between the resolver angle for control and estimated resolver angle exceeds the allowable...
- P0A1B198 MG ECU internal malfunction R/D converter NM stop error (1 trip detection logic)
- P0A1B503 Motor inverter overvoltage signal detection (overvoltage due to MG ECU malfunction)
- P0A1B505 Motor inverter fail signal detection (overcurrent due to MG ECU malfunction)
- P0A1B547 Boost converter overvoltage signal detection (overvoltage due to MG ECU malfunction)
- P0A1B554 Boost converter fail signal detection (overcurrent by MG ECU malfunction)
- P0A1D144 ECU internal error
- P0A1D144 ECU internal error
- P0A2B250 Motor temperature sensor output does not increase under conditions in which the value should increase, or...
- P0A2B250 Motor temperature sensor output does not increase under conditions in which the value should increase, or...
- P0A2B250 w/o Canister Pump Module: Motor temperature sensor output does not increase under conditions in which the...
- P0A2C247 Line short or short to ground in the motor temperature sensor circuit
- P0A2C247 Short or short to GND in the motor temperature sensor circuit
- P0A2C247 Short or short to GND in the motor temperature sensor circuit
- P0A2D249 Open or short to +B in the motor temperature sensor circuit
- P0A2D249 Open or short to +B in the motor temperature sensor circuit
- P0A2D249 Open or short to +B in the motor temperature sensor circuit
- P0A2E248 Unusual sudden change in motor temperature sensor output occurs and the condition continues, or unusual...
- P0A2E248 Unusual sudden change in motor temperature sensor output occurs and the condition continues, or unusual...
- P0A2E248 Unusual sudden change in motor temperature sensor output occurs and the condition continues, or unusual...
- P0A37260 Generator temperature sensor output does not increase in which the value should increase, or output does not...
- P0A37260 Generator temperature sensor output does not increase in which the value should increase, or output does not...
- P0A37260 w/o Canister Pump Module: Generator temperature sensor output does not increase in which the value should...
- P0A38257 Short to GND in the generator temperature sensor circuit
- P0A38257 Short to GND in the generator temperature sensor circuit
- P0A38257 Short to GND in the generator temperature sensor circuit
- P0A39259 Open or short to +B in the generator temperature sensor circuit
- P0A39259 Open or short to +B in the generator temperature sensor circuit
- P0A39259 Open or short to +B in the generator temperature sensor circuit
- P0A3A258 Unusual sudden change in generator temperature sensor output occurs and the condition continues, or unusual...
- P0A3A258 Unusual sudden change in generator temperature sensor output occurs and the condition continues, or unusual...
- P0A3A258 Unusual sudden change in generator temperature sensor output occurs and the condition continues, or unusual...
- P0A3F243 Interphase short in the motor resolver circuit
- P0A3F243 Interphase short in the motor resolver circuit
- P0A40500 Motor resolver output is out of the normal range
- P0A40500 Motor resolver output is out of the normal range
- P0A40504 Motor inverter overvoltage signal detection (overvoltage due to hybrid vehicle transaxle assembly malfunction)
- P0A40506 Motor inverter fail signal detection (overcurrent due to hybrid vehicle transaxle assembly malfunction)
- P0A40549 Boost converter overvoltage signal detection (overvoltage due to hybrid vehicle transaxle assembly...
- P0A40556 Boost converter fail signal detection (overcurrent by hybrid vehicle transaxle assembly malfunction)
- P0A41245 Open or short in the motor resolver circuit
- P0A41245 Open or short in the motor resolver circuit
- P0A4B253 Interphase short in the generator resolver circuit
- P0A4B253 Interphase short in the generator resolver circuit
- P0A4C513 Generator resolver output is out of the normal range
- P0A4C513 Generator resolver output is out of the normal range
- P0A4C518 Generator inverter fail signal detection (overcurrent due to hybrid vehicle transaxle assembly malfunction)
- P0A4D255 Open or short in the generator resolver circuit
- P0A4D255 Open or short in the generator resolver circuit
- P0A51174 Motor current sensor high resolution circuit signal is out of range or there is a difference between it and...
- P0A51174 Motor current sensor high resolution circuit signal is out of range or there is a difference between it and...
- P0A60288 Malfunction in motor inverter current sensor (phase V sub sensor)
- P0A63296 Malfunction in motor inverter current sensor (phase W sub sensor)
- P0A72326 Malfunction in generator inverter current sensor (phase V sub sensor)
- P0A75334 Malfunction in generator inverter current sensor (phase W sub sensor)
- P0A78113 Motor inverter fail signal detection (System overcurrent)
- P0A78113 Motor inverter fail signal detection (System overcurrent)
- P0A78121 Motor inverter overvoltage signal detection (overvoltage due to system malfunction)
- P0A78121 Motor inverter overvoltage signal detection (overvoltage due to system malfunction)
- P0A78128 Abnormal motor current value detection (System malfunction)
- P0A78128 Abnormal motor current value detection (System malfunction)
- P0A78202 Malfunction (short circuit) in the motor inverter inside the inverter with converter assembly
- P0A78202 Malfunction (short circuit) in the motor inverter inside the inverter with converter assembly
- P0A78266 Short to GND in the inverter voltage (VH) signal line
- P0A78279 Motor inverter overvoltage signal detection (overvoltage (inverter malfunction))
- P0A78279 Motor inverter overvoltage signal detection (overvoltage (inverter malfunction))
- P0A78282 Motor inverter overvoltage signal detection (circuit malfunction)
- P0A78282 Motor inverter overvoltage signal detection (circuit malfunction)
- P0A78284 Motor inverter fail signal detection (overheat)
- P0A78284 Motor inverter fail signal detection (overheat)
- P0A78286 Motor inverter fail signal detection (circuit malfunction)
- P0A78286 Motor inverter fail signal detection (circuit malfunction)
- P0A78287 Motor inverter fail signal detection (overcurrent due to inverter assembly malfunction)
- P0A78287 Motor inverter fail signal detection (overcurrent due to inverter assembly malfunction)
- P0A78306 MG2 torque execution monitoring malfunction
- P0A78503 Motor inverter overvoltage signal detection (overvoltage due to MG ECU malfunction)
- P0A78504 Motor inverter overvoltage signal detection (overvoltage due to hybrid vehicle transaxle assembly malfunction)
- P0A78505 Motor inverter fail signal detection (overcurrent due to MG ECU malfunction)
- P0A78506 Motor inverter fail signal detection (overcurrent due to hybrid vehicle transaxle assembly malfunction)
- P0A78548 Boost converter overvoltage signal detection (overvoltage due to inverter assembly malfunction)
- P0A78555 Boost converter fail signal detection (overcurrent by inverter assembly malfunction)
- P0A78565 Motor inverter overvoltage signal detection (circuit malfunction (VH sensor))
- P0A78586 Inverter voltage (VH) sensor performance problem
- P0A7A122 Generator inverter fail signal detection (overcurrent due to system malfunction)
- P0A7A122 Generator inverter fail signal detection (overcurrent due to system malfunction)
- P0A7A130 Abnormal MG1 current value detection (system malfunction)
- P0A7A130 Abnormal MG1 current value detection (system malfunction)
- P0A7A203 Malfunction (short circuit) in the generator inverter inside the inverter with converter assembly
- P0A7A203 Malfunction (short circuit) in the generator inverter inside the inverter with converter assembly
- P0A7A322 Generator inverter fail signal detection (overheat)
- P0A7A322 Generator inverter fail signal detection (overheat)
- P0A7A324 Generator inverter fail signal detection (circuit malfunction)
- P0A7A324 Generator inverter fail signal detection (circuit malfunction)
- P0A7A325 Generator inverter fail signal detection (overcurrent due to inverter assembly malfunction)
- P0A7A325 Generator inverter fail signal detection (overcurrent due to inverter assembly malfunction)
- P0A7A344 MG1 torque execution monitoring malfunction
- P0A7A517 Generator inverter fail signal detection (overcurrent due to MG ECU malfunction)
- P0A7A518 Generator inverter fail signal detection (overcurrent due to hybrid vehicle transaxle assembly malfunction)
- P0A90251 Motor magnetic force deterioration or same phase short circuit
- P0A90251 Motor magnetic force deterioration or same phase short circuit
- P0A90509 Motor system malfunction
- P0A90509 Motor system malfunction
- P0A92261 Generator magnetic force deterioration or same phase short circuit
- P0A92261 Generator magnetic force deterioration or same phase short circuit
- P0A92521 Generator system malfunction
- P0A92521 Generator system malfunction
- P0A93346 Inverter cooling system malfunction HV cooling temperature increases and the temperature of any inverter with...
- P0A93346 Inverter cooling system malfunction HV cooling temperature increases and the temperature of any inverter with...
- P0A93346 Inverter cooling system malfunction HV cooling temperature increases and the temperature of any inverter with...
- P0A94127 Boost converter overvoltage signal detection (overvoltage due to system malfunction)
- P0A94127 Boost converter overvoltage signal detection (overvoltage due to system malfunction)
- P0A94172 Boost converter fail signal detection (overcurrent by system malfunction)
- P0A94172 Boost converter fail signal detection (overcurrent by system malfunction)
- P0A94442 Abnormal voltage execution value
- P0A94547 Boost converter overvoltage signal detection (overvoltage due to MG ECU malfunction)
- P0A94548 Boost converter overvoltage signal detection (overvoltage due to inverter assembly malfunction)
- P0A94549 Boost converter overvoltage signal detection (overvoltage due to hybrid vehicle transaxle assembly...
- P0A94550 Boost converter overvoltage signal detection (circuit malfunction)
- P0A94550 Boost converter overvoltage signal detection (circuit malfunction)
- P0A94553 Boost converter fail signal detection (overheat)
- P0A94553 Boost converter fail signal detection (overheat)
- P0A94554 Boost converter fail signal detection (overcurrent by MG ECU malfunction)
- P0A94555 Boost converter fail signal detection (overcurrent by inverter assembly malfunction)
- P0A94556 Boost converter fail signal detection (overcurrent by hybrid vehicle transaxle assembly malfunction)
- P0A94557 Boost converter fail signal detection (circuit malfunction)
- P0A94557 Boost converter fail signal detection (circuit malfunction)
- P0A94585 Boost converter voltage (VL) sensor performance problem
- P0A94587 Voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate
- P0A94589 Short to GND in the boost converter voltage (VL) sensor circuit
- P0A94590 Open or short to +B in the boost converter voltage (VL) sensor circuit
- P0A95400 Accumulated thermal load of the high voltage fuse estimated by the hybrid vehicle control ECU exceeds the...
- P0AA1231 SMRB on the HV battery positive side is stuck closed.
- P0AA1231 SMRB on the HV battery positive side is stuck closed.
- P0AA1233 SMRP, SMRB and SMRG on the HV battery positive and negative sides are stuck closed.
- P0AA1233 SMRP, SMRB and SMRG on the HV battery positive and negative sides are stuck closed.
- P0AA4232 SMRG on the HV battery negative side stuck closed
- P0AA4232 SMRG on the HV battery negative side stuck closed
- P0AA6526
- P0AA6526
- P0AA7727 Malfunction in the insulation monitoring circuit in the battery smart unit
- P0AA7727 Malfunction in the insulation monitoring circuit in the battery smart unit
- P0AC0817 HV battery current sensor performance problem
- P0AC0817 HV battery current sensor performance problem
- P0ADB227 Short to GND in the SMRB circuit
- P0ADB227 Short to GND in the SMRB circuit
- P0ADC226 Open or short to +B in the SMRB circuit
- P0ADC226 Open or short to +B in the SMRB circuit
- P0ADF229 Short to GND in the SMRG circuit
- P0ADF229 Short to GND in the SMRG circuit
- P0AE0228 Open or +B short in SMRG circuit
- P0AE0228 Open or +B short in SMRG circuit
- P0AE2773 SMRP on the HV battery positive side stuck closed
- P0AE2773 SMRP on the HV battery positive side stuck closed
- P0AE6225 Short to GND in the SMRP circuit
- P0AE6225 Short to GND in the SMRP circuit
- P0AE7224 Open or +B short in SMRP circuit
- P0AE7224 Open or +B short in SMRP circuit
- P0AEE277 Temperature calculated by hybrid vehicle control ECU and actual temperature are different for 10 seconds or...
- P0AEE277 Temperature calculated by power management control ECU and actual temperature are different for 10 seconds or...
- P0AEE277 w/o Canister Pump Module: Temperature calculated by hybrid vehicle control ECU and actual temperature are...
- P0AEF275 Open or short to GND in the motor inverter temperature sensor circuit
- P0AF0274 Short to +B in motor inverter temperature sensor circuit
- P0AF1276 Unusual sudden change in motor inverter temperature sensor output occurs and the offset continues, or unusual...
- P0AF1276 Unusual sudden change in motor inverter temperature sensor output occurs and the offset continues, or unusual...
- P0AF1276 Unusual sudden change in motor inverter temperature sensor output occurs and the offset continues, or unusual...
- P0AFC129 HV battery voltage circuit malfunction
- P0AFC150 Power source voltage of the battery smart unit drops during precharge.
- P0AFC150 Power source voltage of the battery smart unit drops during precharge.
- P0B23129 HV battery voltage circuit malfunction
- P0BCD315 Temperature calculated by hybrid vehicle control ECU and actual temperature are different for 10 seconds or...
- P0BCD315 Temperature calculated by power management control ECU and actual temperature are different for 10 seconds or...
- P0BCD315 w/o Canister Pump Module: Temperature calculated by hybrid vehicle control ECU and actual temperature are...
- P0BCE313 Open or short to GND in the generator inverter temperature sensor signal circuit
- P0BCF312 Short to +B in the generator inverter temperature sensor signal circuit
- P0BD0314 Unusual sudden change in generator inverter temperature sensor output occurs and the offset continues, or...
- P0BD0314 Unusual sudden change in generator inverter temperature sensor output occurs and the offset continues, or...
- P0BD0314 Unusual sudden change in generator inverter temperature sensor output occurs and the offset continues, or...
- P0BEA290 Malfunction in motor inverter current sensor (phase V main sensor) (1 trip detection logic)
- P0BEE298 Malfunction in motor inverter current sensor (phase W main sensor) (1 trip detection logic)
- P0C19306 MG2 torque execution monitoring malfunction
- P0C30390 Charge control error
- P0C30390 Charge control error
- P0C39626 Temperature calculated by hybrid vehicle control ECU and actual temperature are different for 10 seconds or...
- P0C39626 Temperature calculated by power management control ECU and actual temperature are different for 10 seconds or...
- P0C39626 w/o Canister Pump Module: Temperature calculated by hybrid vehicle control ECU and actual temperature are...
- P0C3A621 Open or short to GND in the boost converter temperature sensor (upper) signal circuit
- P0C3B622 Short to +B in the boost converter temperature sensor (upper) signal circuit
- P0C3C625 Unusual sudden change in boost converter temperature sensor (upper) output occurs and the offset continues,...
- P0C3C625 Unusual sudden change in boost converter temperature sensor (upper) output occurs and the offset continues,...
- P0C3C625 Unusual sudden change in boost converter temperature sensor (upper) output occurs and the offset continues,...
- P0C3E628 Temperature calculated by hybrid vehicle control ECU and actual temperature are different for 10 seconds or...
- P0C3E628 Temperature calculated by power management control ECU and actual temperature are different for 10 seconds or...
- P0C3E628 w/o Canister Pump Module: Temperature calculated by hybrid vehicle control ECU and actual temperature are...
- P0C3F623 Open or short to GND in the boost converter temperature sensor (lower) signal circuit
- P0C40624 Short to +B in the boost converter temperature sensor (lower) signal circuit
- P0C41627 Unusual sudden change in boost converter temperature sensor (lower) output occurs and the offset continues,...
- P0C41627 Unusual sudden change in boost converter temperature sensor (lower) output occurs and the offset continues,...
- P0C41627 Unusual sudden change in boost converter temperature sensor (lower) output occurs and the offset continues,...
- P0C73776 A speed or intermittent stop malfunction occurs in the inverter water pump assembly. A revolution malfunction...
- P0C73776 A speed or intermittent stop malfunction occurs in the inverter water pump assembly. A revolution malfunction...
- P0C73776 A speed or intermittent stop malfunction occurs in the inverter water pump assembly. A revolution malfunction...
- P0C76523 Inverter voltage (VH) sensor offset malfunction
- P0C76523 Inverter voltage (VH) sensor offset malfunction
- P0CA3442 Abnormal voltage execution value
- P0D2E565 Motor inverter overvoltage signal detection (circuit malfunction (VH sensor))
- P0D2E586 Inverter voltage (VH) sensor performance problem
- P0D2F266 Short to GND in the inverter voltage (VH) signal line
- P0D30267 Open or short to +B in the inverter voltage (VH) signal line
- P0E05328 Malfunction in generator inverter current sensor (phase V main sensor)* (1 trip detection logic)
- P0E09336 Malfunction in generator inverter current sensor (phase W main sensor)* (1 trip detection logic)
- P0E32564 Boost converter overvoltage signal detection (circuit malfunction (VL sensor))
- P0E32585 Boost converter voltage (VL) sensor performance problem
- P0E33589 Short to GND in the boost converter voltage (VL) sensor circuit
- P0E34590 Open or short to +B in the boost converter voltage (VL) sensor circuit
- P0E71344 MG1 torque execution monitoring malfunction
- P1606308 Shutoff signal from the airbag sensor assembly is determined.
- P1606308 Shutoff signal from the airbag sensor assembly is determined.
- P1C2A155 MG ECU internal malfunction A/D converter malfunction (1 trip detection logic)
- P1C2B192 MG ECU internal malfunction A/D converter malfunction (1 trip detection logic)
- P1C2D587 Voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate
- P1C3C294 Malfunction in motor inverter current sensor (performance problem or open phase V) (1 trip detection logic)
- P1C3D302 Malfunction in motor inverter current sensor (performance problem or open phase W) (1 trip detection logic)
- P1C3E333 Malfunction in generator inverter current sensor (performance problem or open of phase V sensors)* Detects an...
- P1C3F341 Malfunction in generator inverter current sensor (performance problem or open of phase W sensors)* Detects an...
- P1C4A288 Malfunction in motor inverter current sensor (phase V sub sensor) (1 trip detection logic)
- P1C4F296 Malfunction in motor inverter current sensor (phase W sub sensor) (1 trip detection logic)
- P1C54326 Malfunction in generator inverter current sensor (phase V sub sensor)* (1 trip detection logic)
- P1C59334 Malfunction in generator inverter current sensor (phase W sub sensor)* (1 trip detection logic)
- P1C6D501 Malfunction in motor inverter current sensor (phase V main and sub sensors offset) (1 trip detection logic)
- P1C6E502 Malfunction in motor inverter current sensor (phase W main and sub sensors offset) (1 trip detection logic)
- P1C71515 Malfunction in generator inverter current sensor (phase V main and sub sensors offset)* (1 trip detection...
- P1C72516 Malfunction in generator inverter current sensor (phase W main and sub sensors offset)* (1 trip detection...
- P1C73512 MG ECU internal malfunction Standard voltage for analog signal (+5 V) error (1 trip detection logic)
- P1CA6156 MG ECU internal malfunction CPU ROM-RAM error (1 trip detection logic)
- P1CA7193 MG ECU internal malfunction CPU ROM-RAM error (1 trip detection logic)
- P1CAC200 The difference between the resolver angle for control and estimated resolver angle exceeds the allowable...
- P1CAD168 The difference between the resolver angle for control and estimated resolver angle exceeds the allowable...
- P1CAF792 Resolver REF signal cycle error
- P1CB0795 Resolver REF signal cycle error
- P1CB2793 Resolver REF signal oscillation stop error
- P1CB3796 Resolver REF signal oscillation stop error
- P2120152 Main sensor circuit wiring malfunction or level is not stable
- P2120152 Main sensor circuit wiring malfunction or level is not stable
- P2121106 Internal error of the main sensor
- P2121106 Internal error of the main sensor
- P2122104 Open or short to GND in the main sensor circuit
- P2122104 Open or short to GND in the main sensor circuit
- P2123105 Short to +B in the main sensor circuit
- P2123105 Short to +B in the main sensor circuit
- P2125153 Sub sensor circuit wiring malfunction or level is not stable
- P2125153 Sub sensor circuit wiring malfunction or level is not stable
- P2126109 Internal error of the sub sensor
- P2126109 Internal error of the sub sensor
- P2127107 Open or short to GND in the sub sensor circuit
- P2127107 Open or short to GND in the sub sensor circuit
- P2128108 Short to +B in the sub sensor circuit
- P2128108 Short to +B in the sub sensor circuit
- P2138110 Difference between the main sensor value and sub sensor value is large.
- P2138110 Difference between the main sensor value and sub sensor value is large.
- P2228268 Open or short to GND in the atmospheric pressure sensor
- P2228268 Open or short to GND in the atmospheric pressure sensor
- P2229269 Short to +B in the atmospheric pressure sensor
- P2229269 Short to +B in the atmospheric pressure sensor
- P2511149 When the power switch is on (READY), the hybrid vehicle control ECU is reset.
- P2511149 When the power switch is on (READY), the power management control ECU is reset.
- P2532772 Voltage is still applied to IG2 terminal although an IG2 relay off command is received from the power source...
- P2532772 Voltage is still applied to IG2 terminal although an IG2 relay off command is received from the power source...
- P3000388 Discharge inhibition control malfunction
- P3000388 Discharge inhibition control malfunction
- P3000388 Discharge inhibition control malfunction
- P3000388 Discharge inhibition control malfunction
- P3000389 HV battery voltage drops
- P3000389 HV battery voltage drops
- P3000389 HV battery voltage drops
- P3000389 HV battery voltage drops
- P3000603 The hybrid vehicle control ECU detects a HV battery cooling system error signal.
- P3000603 The power management control ECU detects a HV battery cooling system error signal.
- P3004131 One of the following occurs during pre-charge (the time from when SMRP turns on until SMRG turns on): ·...
- P3004131 One of the following occurs during pre-charge (the time from when SMRP turns on until SMRG turns on): ·...
- P3004132 The inverter is not precharged.
- P3004132 The inverter is not precharged.
- P3004133 A high-voltage wiring system error signal is detected in the hybrid vehicle control ECU
- P3004133 A high-voltage wiring system error signal is detected in the power management control ECU
- P3004800 Excessive overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on).
- P3004800 Excessive overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on).
- P3004803 One of the following occurs while the power switch is on (READY): · Electric battery fuse in the service plug...
- P3004803 One of the following occurs while the power switch is on (READY): · Electric battery fuse in the service plug...
- P3107213 Short to GND in the communication circuit
- P3107213 Short to GND in the communication circuit
- P3107214 Open or short to +B in the communication circuit
- P3107214 Open or short to +B in the communication circuit
- P3107215 Abnormal communication signal
- P3107215 Abnormal communication signal
- P3108536 A/C inverter malfunction
- P3108536 A/C inverter malfunction
- P3110223 There is a short to +B in the IGCT relay or the IGCT relay is stuck closed.
- P3110223 There is a short to +B in the IGCT relay or the IGCT relay is stuck closed.
- P3133659 MG ECU internal malfunction Communication error (from generator (MG1) to motor (MG2)) (1 trip detection logic)
- P3134661 MG ECU internal malfunction Communication error (from motor (MG2) to generator (MG1)) (1 trip detection logic)
- P3147239 Hybrid vehicle transaxle input malfunction (shaft damaged)
- P3147239 Hybrid vehicle transaxle input malfunction (shaft damaged)
- P3147239 Hybrid vehicle transaxle input malfunction (shaft damaged)
- P3147239 Hybrid vehicle transaxle input malfunction (shaft damaged)
- P3147240 MG1 locked
- P3147240 MG1 locked
- P314A828 The water pump speed signal is not sent to the hybrid vehicle control ECU when the power switch is turned on...
- P314A828 The water pump speed signal is not sent to the hybrid vehicle control ECU when the power switch is turned on...
- P314A828 The water pump speed signal is not sent to the power management control ECU when the ignition switch is...
- P321E318 · An open or ground short in the HV gate block signal circuit when the gate is operating · When the HV gate...
- P321E318 · An open or ground short in the HV gate block signal circuit when the gate is operating · When the HV gate...
- P321F319 · An open or ground short in the HV gate block signal circuit when the gate is operating · When the HV gate...
- P321F319 · An open or ground short in the HV gate block signal circuit when the gate is operating · When the HV gate...
- P324E788 Error in reset signal from the inverter assembly power source IC
- P324E788 Error in reset signal from the inverter assembly power source IC
- U0100530 Problem with CAN communication between the ECM and hybrid vehicle control ECU (CAN communication system...
- U0100530 Problem with CAN communication between the ECM and power management control ECU (CAN communication system...
- U0110159 Error in reception from inverter with converter assembly (MG ECU) via serial communication (out of...
- U0110159 Error in reception from inverter with converter assembly (MG ECU) via serial communication (out of...
- U0110160 Error in signal transmission to the inverter with converter assembly (MG ECU) via serial communication (no...
- U0110194 Error in signal transmission to the inverter with converter assembly (MG ECU) via serial communication (no...
- U0129527 Problem with CAN communication (V BUS) between the skid control ECU assembly and hybrid vehicle control ECU...
- U0129527 Problem with CAN communication (V BUS) between the skid control ECU assembly and power management control ECU...
- U0140146 Problem with CAN communication between the main body ECU and hybrid vehicle control ECU (CAN communication...
- U0151763 Problem with CAN communication between airbag sensor assembly and hybrid vehicle control ECU (CAN...
- U0151763 Problem with CAN communication between airbag sensor assembly and power management control ECU (CAN...
- U0164827 Problem with CAN communication between air conditioning amplifier assembly and hybrid vehicle control ECU...
- U0164827 Problem with CAN communication between air conditioning amplifier assembly and power management control ECU...
- U0424537 Air conditioning amplifier assembly malfunction
- U1107436 Problem with CAN communication between the power source ECU and hybrid vehicle control ECU (CAN communication...
- U1107436 Problem with CAN communication between the power source ECU and power management control ECU (CAN...
- P0A7F123 · Internal resistance of the HV battery is higher than the standard (1 trip detection) · Difference in the...
- P0A7F123 · Internal resistance of the HV battery is higher than the standard (1 trip detection) · Difference in the...
- P0A7F123 · Internal resistance of the HV battery is higher than the standard (1 trip detection) · Difference in the...
- P0A7F123 · Internal resistance of the HV battery is higher than the standard (1 trip detection) · Difference in the...
- P0A80123 Difference in voltage between battery blocks is larger than the standard (2 trip detection)
- P0A80123 Difference in voltage between battery blocks is larger than the standard (2 trip detection)
- P0A80123 Difference in voltage between battery blocks is larger than the standard (2 trip detection)
- P0A80123 Difference in voltage between battery blocks is larger than the standard (2 trip detection)
- P0A82123 The speed of the battery cooling blower assembly is not within the specified range (1 trip detection)
- P0A82123 The speed of the battery cooling blower assembly is not within the specified range (1 trip detection)
- P0A82123 The speed of the battery cooling blower assembly is not within the specified range (1 trip detection)
- P0A82123 w/o Canister Pump Module: The speed of the battery cooling blower assembly is not within the specified range...
- P0A84123 When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target...
- P0A84123 When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target...
- P0A84123 When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target...
- P0A84123 w/o Canister Pump Module: When the speed calculated based on the battery cooling blower assembly frequency is...
- P0A85123 When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target...
- P0A85123 When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target...
- P0A85123 When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target...
- P0A85123 w/o Canister Pump Module: When the speed calculated based on the battery cooling blower assembly frequency is...
- P0A95123 Voltage between VB8 and VB9 terminals is below the standard despite the interlock switch being engaged (1...
- P0A95123 Voltage between VB8 and VB9 terminals is below the standard despite the interlock switch being engaged (1...
- P0A95123 Voltage between VB8 and VB9 terminals is below the standard despite the interlock switch being engaged (1...
- P0A9C123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P0A9C123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P0A9C123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P0A9D123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0A9D123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0A9D123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0A9E123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0A9E123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0A9E123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0AAE123 When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open...
- P0AAE123 When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open...
- P0AAE123 When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open...
- P0AAF123 When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open...
- P0AAF123 When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open...
- P0AAF123 When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open...
- P0ABF123 When the battery current sensor is abnormal (1 trip detection)
- P0ABF123 When the battery current sensor is abnormal (1 trip detection)
- P0ABF123 When the battery current sensor is abnormal (1 trip detection)
- P0AC0123 When the battery current sensor is abnormal (1 or 2 trip detection)
- P0AC0123 When the battery current sensor is abnormal (1 or 2 trip detection)
- P0AC1123 When the battery current sensor is abnormal (1 trip detection)
- P0AC1123 When the battery current sensor is abnormal (1 trip detection)
- P0AC1123 When the battery current sensor is abnormal (1 trip detection)
- P0AC2123 When the battery current sensor is abnormal (1 trip detection)
- P0AC2123 When the battery current sensor is abnormal (1 trip detection)
- P0AC2123 When the battery current sensor is abnormal (1 trip detection)
- P0AC6123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P0AC6123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P0AC6123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P0AC7123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0AC7123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0AC7123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0AC8123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0AC8123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0AC8123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0ACB123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P0ACB123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P0ACB123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P0ACC123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0ACC123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0ACC123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0ACD123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0ACD123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0ACD123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than...
- P0AFC123 The hybrid vehicle control ECU receives an error signal from the battery smart unit.
- P0AFC123 The power management control ECU receives an error signal from the battery smart unit.
- P0B3D123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B3D123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B3D123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B42123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B42123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B42123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B47123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B47123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B47123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B4C123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B4C123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B4C123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B51123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B51123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B51123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B56123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B56123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B56123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B5B123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B5B123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B5B123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B60123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B60123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B60123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B65123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B65123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B65123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B6A123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B6A123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B6A123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B6F123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B6F123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P0B6F123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P3011123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3011123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3011123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3011123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3012123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3012123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3012123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3012123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3013123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3013123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3013123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3013123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3014123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3014123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3014123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3014123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3015123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3015123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3015123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3015123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3016123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3016123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3016123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3016123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3017123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3017123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3017123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3017123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3018123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3018123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3018123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3018123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3019123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3019123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3019123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3019123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3020123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3020123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3020123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3020123 Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
- P3065123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P3065123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P3065123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
- P308A123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P308A123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- P308A123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
- U029A123 Problem in serial communication between the battery smart unit and hybrid vehicle control ECU (1 trip...
- U029A123 Problem in serial communication between the battery smart unit and power management control ECU (1 trip...
- P0571Voltage of STP signal and that of ST1- signal of hybrid vehicle control ECU are less than 1 V for 0.5 seconds...
- P0571Voltage of STP signal and that of ST1- signal of hybrid vehicle control ECU are less than 1 V for 0.5 seconds...
- P0571Voltage of STP signal and that of ST1- signal of power management control ECU are less than 1 V for 0.5...
- P0575When both of the following conditions are met: · STP signals input to the hybrid vehicle control ECU...
- P0575When both of the following conditions are met: · STP signals input to the hybrid vehicle control ECU...
- P0575When both of the following conditions are met: · STP signals input to the power management control ECU...
- P1578The hybrid vehicle control ECU receives a brake system error signal for 0.2 sec. or more while the cruise...
- P1578The hybrid vehicle control ECU receives a brake system error signal for 0.2 sec. or more while the cruise...
- P1578The power management control ECU receives a brake system error signal for 0.2 sec. or more while the cruise...
- U0122While power switch is on (IG), communication stop between brake booster with master cylinder assembly (skid...
- U0122While power switch is on (IG), communication stop between brake booster with master cylinder assembly (skid...
- U0122While power switch is on (IG), communication stop between brake booster with master cylinder assembly (skid...
- B1247In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent...
- C2111/11 Tire pressure warning valve and transmitters stop transmitting signals
- C2111/11 Tire pressure warning valve and transmitters stop transmitting signals
- C2112/12 Tire pressure warning valve and transmitters stop transmitting signals
- C2112/12 Tire pressure warning valve and transmitters stop transmitting signals
- C2113/13 Tire pressure warning valve and transmitters stop transmitting signals
- C2113/13 Tire pressure warning valve and transmitters stop transmitting signals
- C2114/14 Tire pressure warning valve and transmitters stop transmitting signals
- C2114/14 Tire pressure warning valve and transmitters stop transmitting signals
- C2121/21 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2121/21 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2122/22 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2122/22 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2123/23 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2123/23 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2124/24 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2124/24 Following condition (a) or (b) is met: (a) When all conditions below are met: · Tire pressure warning valve...
- C2126/26 After transmitter ID registration is completed, ECU does not receive radio waves from transmitters whose IDs...
- C2126/26 After transmitter ID registration is completed, ECU does not receive radio waves from transmitters whose IDs...
- C2141/41 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2142/42 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2143/43 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2144/44 If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will...
- C2171/71 Transmitter ID code is not registered. (When an ID code is unregistered for 3 minutes or more)
- C2176/76 Malfunction in the tire pressure warning ECU and receiver internal circuit
- C2177/77 All conditions below are met: · During initialization · Tire pressure warning valve and transmitter is not in...
- C2177/77 All conditions below are met: · During initialization · Tire pressure warning valve and transmitter is not in...
- C2179/79 Communication between the main body ECU (multiplex network body ECU) and tire pressure warning ECU and...
- C2181/81 Test mode procedure is performed.
- C2181/81 Test mode procedure is performed.
- C2182/82 Test mode procedure is performed.
- C2182/82 Test mode procedure is performed.
- C2183/83 Test mode procedure is performed.
- C2183/83 Test mode procedure is performed.
- C2184/84 Test mode procedure is performed.
- C2184/84 Test mode procedure is performed.
- C2198/98 Test mode procedure is performed.
- C1202/68 An open is detected in the switch signal circuit for 2 seconds or more.
- C1202/68 An open is detected in the switch signal circuit for 2 seconds or more.
- C1202/68 An open is detected in the switch signal circuit for 2 seconds or more.
- C1202/68 An open is detected in the switch signal circuit for 2 seconds or more.
- C1203/95 Either of the following is detected: 1. Identification information sent from other ECUs does not match with...
- C1203/95 Either of the following is detected: 1. Identification information sent from other ECUs does not match with...
- C1210/36 Yaw rate sensor zero point calibration is incomplete.
- C1210/36 Yaw rate sensor zero point calibration is incomplete.
- C1210/36 Yaw rate sensor zero point calibration is incomplete.
- C1211/25 Excess current is applied for 0.05 seconds or more.
- C1211/25 Excess current is applied for 0.05 seconds or more.
- C1211/25 Excess current is applied for 0.05 seconds or more.
- C1211/25 Excess current is applied for 0.05 seconds or more.
- C1212/26 Excess current is applied for 0.05 seconds or more.
- C1212/26 Excess current is applied for 0.05 seconds or more.
- C1212/26 Excess current is applied for 0.05 seconds or more.
- C1212/26 Excess current is applied for 0.05 seconds or more.
- C1214/62 Decrease in hydraulic pressure control performance. (Pressure increase malfunction)
- C1214/62 Decrease in hydraulic pressure control performance. (Pressure increase malfunction)
- C1214/62 Decrease in hydraulic pressure control performance. (Pressure increase malfunction)
- C1214/62 Decrease in hydraulic pressure control performance. (Pressure increase malfunction)
- C1225/31 Excess current is applied for 0.05 seconds or more.
- C1225/31 Excess current is applied for 0.05 seconds or more.
- C1225/31 Excess current is applied for 0.05 seconds or more.
- C1225/31 Excess current is applied for 0.05 seconds or more.
- C1226/32 Excess current is applied for 0.05 seconds or more.
- C1226/32 Excess current is applied for 0.05 seconds or more.
- C1226/32 Excess current is applied for 0.05 seconds or more.
- C1226/32 Excess current is applied for 0.05 seconds or more.
- C1227/33 Excess current is applied for 0.05 seconds or more.
- C1227/33 Excess current is applied for 0.05 seconds or more.
- C1227/33 Excess current is applied for 0.05 seconds or more.
- C1227/33 Excess current is applied for 0.05 seconds or more.
- C1228/34 Excess current is applied for 0.05 seconds or more.
- C1228/34 Excess current is applied for 0.05 seconds or more.
- C1228/34 Excess current is applied for 0.05 seconds or more.
- C1228/34 Excess current is applied for 0.05 seconds or more.
- C1231/31 While steering angle sensor communication is enabled, a malfunction signal output is received during the...
- C1231/31 While steering angle sensor communication is enabled, a malfunction signal output is received during the...
- C1231/31 While steering angle sensor communication is enabled, a malfunction signal output is received during the...
- C1231/31 While steering angle sensor communication is enabled, a malfunction signal output is received during the...
- C1234/34 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor...
- C1234/34 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor...
- C1234/34 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor...
- C1234/34 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor...
- C1235/35 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1235/35 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1235/35 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1235/35 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1236/36 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1236/36 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1236/36 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1236/36 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1238/38 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1238/38 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1238/38 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1238/38 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1239/39 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1239/39 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1239/39 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1239/39 Either of the following is detected: 1. When driving at 20 km/h (12 mph) or more, noise occurs on the speed...
- C1241/41 Any of the following conditions when the BS terminal voltage is 9.3 V or less: 1. Vehicle not decelerated...
- C1241/41 Any of the following conditions when the BS terminal voltage is 9.3 V or less: 1. Vehicle not decelerated...
- C1241/41 Any of the following conditions when the BS terminal voltage is 9.3 V or less: 1. Vehicle not decelerated...
- C1241/41 Any of the following conditions when the BS terminal voltage is 9.3 V or less: 1. Vehicle not decelerated...
- C1242/42 Voltage is not applied to the IG1 terminal (less than 3.5 V), and applied to the IG2 terminal (9.5 V or more)...
- C1242/42 Voltage is not applied to the IG1 terminal (less than 3.5 V), and applied to the IG2 terminal (9.5 V or more)...
- C1242/42 Voltage is not applied to the IG1 terminal (less than 3.5 V), and applied to the IG2 terminal (9.5 V or more)...
- C1242/42 Voltage is not applied to the IG1 terminal (less than 3.5 V), and applied to the IG2 terminal (9.5 V or more)...
- C1243/43 An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h...
- C1243/43 An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h...
- C1243/43 An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h...
- C1243/43 An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h...
- C1244/44 Either of the following is detected: 1. Difference between GL1 and GL2 does not become less than 0.4 G for 60...
- C1244/44 Either of the following is detected: 1. Difference between GL1 and GL2 does not become less than 0.4 G for 60...
- C1244/44 Either of the following is detected: 1. Difference between GL1 and GL2 does not become less than 0.4 G for 60...
- C1244/44 Either of the following is detected: 1. Difference between GL1 and GL2 does not become less than 0.4 G for 60...
- C1245/45 Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the...
- C1245/45 Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the...
- C1245/45 Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the...
- C1245/45 Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the...
- C1246/46 Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds.
- C1246/46 Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds.
- C1246/46 Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds.
- C1246/46 Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds.
- C1247/47 Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.2 seconds or more.
- C1249/49 When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or...
- C1249/49 When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or...
- C1249/49 When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or...
- C1249/49 When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or...
- C1249/49 When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or...
- C1252/52 The pump motor is operating continuously for 178 seconds or more. (When relay malfunction is 98 seconds or...
- C1252/52 The pump motor is operating continuously for 178 seconds or more. (When relay malfunction is 98 seconds or...
- C1252/52 The pump motor is operating continuously for 178 seconds or more. (When relay malfunction is 98 seconds or...
- C1252/52 The pump motor is operating continuously for 178 seconds or more. (When relay malfunction is 98 seconds or...
- C1253/53 With the IG1 terminal voltage 9.5 V or more, the motor drive monitor remains off for 0.2 seconds or more...
- C1253/53 With the IG1 terminal voltage 9.5 V or more, the motor drive monitor remains off for 0.2 seconds or more...
- C1253/53 With the IG1 terminal voltage 9.5 V or more, the motor drive monitor remains off for 0.2 seconds or more...
- C1253/53 With the IG1 terminal voltage 9.5 V or more, the motor drive monitor remains off for 0.2 seconds or more...
- C1256/56 Significant drop in accumulator pressure continues. (DTCs will be stored and the buzzer will operate when...
- C1256/56 Significant drop in accumulator pressure continues. (DTCs will be stored and the buzzer will operate when...
- C1256/56 Significant drop in accumulator pressure continues. (DTCs will be stored and the buzzer will operate when...
- C1256/56 Significant drop in accumulator pressure continues. (DTCs will be stored and the buzzer will operate when...
- C1257/57 While accumulator pressure falls below hard pump ON pressure, the hard drive circuit does not operate for 1...
- C1259/58 The regeneration malfunction signal is input for at least 0.036 seconds when IG2 terminal voltage is 9.5 V or...
- C1259/58 The regeneration malfunction signal is input for at least 0.036 seconds when IG2 terminal voltage is 9.5 V or...
- C1271/71 Detected only during Test Mode.
- C1271/71 Detected only during Test Mode.
- C1271/71 Detected only during Test Mode.
- C1271/71 Detected only during Test Mode.
- C1272/72 Detected only during Test Mode.
- C1272/72 Detected only during Test Mode.
- C1272/72 Detected only during Test Mode.
- C1272/72 Detected only during Test Mode.
- C1273/73 Detected only during Test Mode.
- C1273/73 Detected only during Test Mode.
- C1273/73 Detected only during Test Mode.
- C1273/73 Detected only during Test Mode.
- C1274/74 Detected only during Test Mode.
- C1274/74 Detected only during Test Mode.
- C1274/74 Detected only during Test Mode.
- C1274/74 Detected only during Test Mode.
- C1275/75 Detected only during Test Mode.
- C1275/75 Detected only during Test Mode.
- C1275/75 Detected only during Test Mode.
- C1275/75 Detected only during Test Mode.
- C1276/76 Detected only during Test Mode.
- C1276/76 Detected only during Test Mode.
- C1276/76 Detected only during Test Mode.
- C1276/76 Detected only during Test Mode.
- C1277/77 Detected only during Test Mode.
- C1277/77 Detected only during Test Mode.
- C1277/77 Detected only during Test Mode.
- C1277/77 Detected only during Test Mode.
- C1278/78 Detected only during Test Mode.
- C1278/78 Detected only during Test Mode.
- C1278/78 Detected only during Test Mode.
- C1278/78 Detected only during Test Mode.
- C1279/79 Detected only during Test Mode.
- C1279/79 Detected only during Test Mode.
- C1279/79 Detected only during Test Mode.
- C1279/79 Detected only during Test Mode.
- C1281/81 Detected only during Test Mode.
- C1281/81 Detected only during Test Mode.
- C1281/81 Detected only during Test Mode.
- C1281/81 Detected only during Test Mode.
- C1290/66 The steering angle sensor zero point is judged as an abnormal value.
- C1290/66 The steering angle sensor zero point is judged as an abnormal value.
- C1290/66 The steering angle sensor zero point is judged as an abnormal value.
- C1290/66 The steering angle sensor zero point is judged as an abnormal value.
- C1300Skid control ECU internal malfunction.
- C1300Skid control ECU internal malfunction.
- C1300Skid control ECU internal malfunction.
- C1310/51 The internal malfunction signal is input for at least 0.072 seconds when IG2 terminal voltage is 10.5 V or...
- C1310/51 The internal malfunction signal is input for at least 0.072 seconds when IG2 terminal voltage is 10.5 V or...
- C1311/11 Either of the following is detected: 1. When the power switch is on (ready): The ABS main relay contact is...
- C1311/11 Either of the following is detected: 1. When the power switch is on (ready): The ABS main relay contact is...
- C1311/11 Either of the following is detected: 1. When the power switch is on (ready): The ABS main relay contact is...
- C1311/11 Either of the following is detected: 1. When the power switch is on (ready): The ABS main relay contact is...
- C1312/12 The ABS main relay contact is turned ON (BS terminal voltage 3.5 V or more) for 4.5 seconds or more when ABS...
- C1312/12 The ABS main relay contact is turned ON (BS terminal voltage 3.5 V or more) for 4.5 seconds or more when ABS...
- C1312/12 The ABS main relay contact is turned ON (BS terminal voltage 3.5 V or more) for 4.5 seconds or more when ABS...
- C1312/12 The ABS main relay contact is turned ON (BS terminal voltage 3.5 V or more) for 4.5 seconds or more when ABS...
- C1336/98 Either of the following is detected: 1. The vehicle is driven normally without zero point calibration...
- C1336/98 Either of the following is detected: 1. The vehicle is driven normally without zero point calibration...
- C1336/98 Either of the following is detected: 1. The vehicle is driven normally without zero point calibration...
- C1345/66 Linear valve offset learning undone.
- C1345/66 Linear valve offset learning undone.
- C1345/66 Linear valve offset learning undone.
- C1346/71 Detected only during Test Mode.
- C1352/21 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1352/21 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1352/21 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1352/21 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1353/23 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1353/23 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1353/23 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1353/23 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1356/22 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1356/22 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1356/22 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1356/22 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1357/24 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1357/24 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1357/24 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1357/24 When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more.
- C1364/61 Sensor supply voltage 1 (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds or more.
- C1364/61 Sensor supply voltage 1 (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds or more.
- C1364/61 Sensor supply voltage 1 (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds or more.
- C1364/61 Sensor supply voltage 1 (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds or more.
- C1365/54 Sensor supply voltage (VACC) is 4.54 V or less, or 5.46 V or more for 0.8 seconds or more.
- C1365/54 Sensor supply voltage (VACC) is 4.54 V or less, or 5.46 V or more for 0.8 seconds or more.
- C1365/54 Sensor supply voltage (VACC) is 4.54 V or less, or 5.46 V or more for 0.8 seconds or more.
- C1365/54 Sensor supply voltage (VACC) is 4.54 V or less, or 5.46 V or more for 0.8 seconds or more.
- C1368/67 Offset learned value out of specification.
- C1368/67 Offset learned value out of specification.
- C1368/67 Offset learned value out of specification.
- C1380/64 When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is...
- C1381/97 While yaw rate and acceleration sensor communication is enabled, a supply voltage malfunction signal is...
- C1381/97 While yaw rate and acceleration sensor communication is enabled, a supply voltage malfunction signal is...
- C1381/97 While yaw rate and acceleration sensor communication is enabled, a supply voltage malfunction signal is...
- C1381/97 While yaw rate and acceleration sensor communication is enabled, a supply voltage malfunction signal is...
- C1391/69 Either of the following is detected: 1. Accumulator pressure sensor input does not increase before braking or...
- C1391/69 Either of the following is detected: 1. Accumulator pressure sensor input does not increase before braking or...
- C1391/69 Either of the following is detected: 1. Accumulator pressure sensor input does not increase before braking or...
- C1392/48 Zero point calibration of brake pedal stroke sensor assembly is unfinished.
- C1439/66 After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1439/66 After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1439/66 After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1439/66 After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1440/98 Driving at a steep bank angle.
- C1440/98 Driving at a steep bank angle.
- C1440/98 Driving at a steep bank angle.
- C1442/44 With terminal IG1 voltage between 9.5 and 17.4 V, an invalid data signal is received from the acceleration...
- C1442/44 With terminal IG1 voltage between 9.5 and 17.4 V, an invalid data signal is received from the acceleration...
- C1442/44 With terminal IG1 voltage between 9.5 and 17.4 V, an invalid data signal is received from the acceleration...
- C1443/34 With terminal IG1 voltage between 9.5 and 17.4 V, an invalid data signal is received from the yaw rate sensor...
- C1443/34 With terminal IG1 voltage between 9.5 and 17.4 V, an invalid data signal is received from the yaw rate sensor...
- C1443/34 With terminal IG1 voltage between 9.5 and 17.4 V, an invalid data signal is received from the yaw rate sensor...
- C1445/66 Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1445/66 Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1445/66 Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1445/66 Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1451/72 Air bleeding has not been performed.
- C1464/31 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1464/31 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1464/31 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1464/31 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1465/32 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1465/32 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1465/32 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1465/32 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1466/33 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1466/33 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1466/33 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1466/33 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1467/34 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1467/34 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1467/34 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- C1467/34 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from...
- U0073/94 Either of the following is detected: 1. Yaw rate and acceleration sensor communication is disabled for 1...
- U0073/94 Either of the following is detected: 1. Yaw rate and acceleration sensor communication is disabled for 1...
- U0073/94 Either of the following is detected: 1. Yaw rate and acceleration sensor communication is disabled for 1...
- U0073/94 Either of the following is detected: 1. Yaw rate and acceleration sensor communication is disabled for 1...
- U0073/94 Either of the following is detected: 1. Yaw rate and acceleration sensor communication is disabled for 1...
- U0120/96 Push start switch data is invalid for 3 seconds or more.
- U0120/96 Push start switch data is invalid for 3 seconds or more.
- U0120/96 Push start switch data is invalid for 3 seconds or more.
- U0123/62 Yaw rate sensor communication is disabled for 1 second or more.
- U0123/62 Yaw rate sensor communication is disabled for 1 second or more.
- U0123/62 Yaw rate sensor communication is disabled for 1 second or more.
- U0123/62 Yaw rate sensor communication is disabled for 1 second or more.
- U0123/62 Yaw rate sensor communication is disabled for 1 second or more.
- U0124/95 Acceleration sensor communication is disabled for 1 second or more.
- U0124/95 Acceleration sensor communication is disabled for 1 second or more.
- U0124/95 Acceleration sensor communication is disabled for 1 second or more.
- U0124/95 Acceleration sensor communication is disabled for 1 second or more.
- U0124/95 Acceleration sensor communication is disabled for 1 second or more.
- U0126/63 Steering angle sensor communication is disabled for 1 second or more.
- U0126/63 Steering angle sensor communication is disabled for 1 second or more.
- U0126/63 Steering angle sensor communication is disabled for 1 second or more.
- U0126/63 Steering angle sensor communication is disabled for 1 second or more.
- U0126/63 Steering angle sensor communication is disabled for 1 second or more.
- U0293/59 Either of the following is detected: 1. With the IG2 terminal voltage 9.5 V or more, data from the hybrid...
- U0293/59 Either of the following is detected: 1. With the IG2 terminal voltage 9.5 V or more, data from the hybrid...
- U0293/59 Either of the following is detected: 1. With the IG2 terminal voltage 9.5 V or more, data from the hybrid...
- U0293/59 Either of the following is detected: 1. With the IG2 terminal voltage 9.5 V or more, data from the power...
- U0293/59 Either of the following is detected: 1. With the IG2 terminal voltage 9.5 V or more, data from the power...
- C1511/11 Diagnosis Condition: IG ON Malfunction Status: TRQ1 voltage is less than 0.25 V or more than 4.6 V
- C1512/12 Diagnosis Condition: IG ON Malfunction Status: TRQ2 voltage is less than 0.25 V or more than 4.6 V
- C1513/13 Deviation of torque sensor TRQ1 and TRQ2 exceeds specified values
- C1514/14 Diagnosis Condition: IG ON Malfunction Status: TRQV voltage is less than 4.5 V or more than 5.5 V.
- C1515/15 This DTC is stored when torque sensor zero point calibration has not been performed.
- C1516/16 Torque sensor zero point calibration is incomplete due to the steering wheel being touched during calibration.
- C1517/17 Temporary control due to malfunction related to torque sensor continues for long time
- C1524/24 Short (or open) in motor circuit or abnormal voltage in motor circuit
- C1531/31 ECU internal malfunction (CPU malfunction)
- C1532/32 ECU internal malfunction (Peripheral circuit malfunction)
- C1533/33 ECU internal malfunction (Substrate temperature sensor malfunction)
- C1534/34 ECU internal malfunction (EEPROM error)
- C1535/35 ECU internal malfunction (Steering wheel location data error)
- C1551/51 Open or short in IG power source circuit with power switch ON
- C1552/52 PIG power source circuit malfunction
- C1553/53 · PIG power source overvoltage · IG power source overvoltage
- C1554/54 Power source relay circuit malfunction
- C1555/55 Predriver (Motor relay circuit) malfunction
- C1581/81 Assist map not written in power steering ECU assembly
- C1581/81 Assist map not written in power steering ECU assembly
- C1581/81 Assist map not written in power steering ECU assembly
- C1582/82 Assist map number mismatch
- C1582/82 Assist map number mismatch
- C1582/82 Assist map number mismatch
- U0129/93 Lost communication with brake booster with master cylinder assembly
- U0129/93 Lost communication with brake booster with master cylinder assembly
- U0293/92 Lost communication with hybrid vehicle control ECU
- U0293/92 Lost communication with power management control ECU
- B2781One of the following conditions is met (1-trip detection logic*1): · The steering lock/unlock position sensor...
- B2781One of the following conditions is met (1-trip detection logic*1): · The steering lock/unlock position sensor...
- B2782Either condition is met (1-trip detection logic*): · The steering lock motor activation command circuit has a...
- B2782Either condition is met (1-trip detection logic*): · The steering lock motor activation command circuit has a...
- B2782Either condition is met (1-trip detection logic*): · The steering lock motor activation command circuit has a...
- B2788Mismatch between the steering lock ECU IG2 input from the LIN communication system and from the direct line...
- B2788Mismatch between the steering lock ECU IG2 input from the LIN communication system and from the direct line...
- B2287There is an open, short or ECU communication malfunction between power management control ECU and...
- B2287There is an open, short or ECU communication malfunction between power management control ECU and...
- B2321No communication between power window regulator motor assembly (for driver door) and main body ECU (multiplex...
- B2325Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the...
- B2785· Errors in LIN communication between ECUs or an open or short in communication lines · LIN communication...
- B2785· Errors in LIN communication between ECUs or an open or short in communication lines · LIN communication...
- B2786No communication between steering lock ECU (steering lock actuator assembly) and certification ECU (smart key...
- B2786No communication between steering lock ECU (steering lock actuator assembly) and certification ECU (smart key...
- B2789No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU)...
- B2789No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU)...
- B278CAn internal malfunction occurs in the certification ECU (smart key ECU assembly).
- B278CAn internal malfunction occurs in the certification ECU (smart key ECU assembly).
- B278CNo communication between the certification ECU (smart key ECU assembly) and power management control ECU for...
- U0100The hybrid vehicle control computer assembly does not receive data from the ECM.
- U0100The hybrid vehicle control computer assembly does not receive data from the ECM.
- U0100The hybrid vehicle control computer assembly does not receive data from the ECM.
- U0100The hybrid vehicle control computer assembly does not receive data from the ECM.
- U0100The power management control ECU does not receive data from the ECM.
- U0129No communication from the brake booster with master cylinder assembly (skid control ECU) continues.
- U0129No communication from the brake booster with master cylinder assembly (skid control ECU) continues.
- U0129No communication from the brake booster with master cylinder assembly (skid control ECU) continues.
- U0129The hybrid vehicle control computer assembly does not receive data from the brake booster with master...
- U0129The hybrid vehicle control computer assembly does not receive data from the brake booster with master...
- U0129The hybrid vehicle control computer assembly does not receive data from the brake booster with master...
- U0129The hybrid vehicle control computer assembly does not receive data from the brake booster with master...
- U0129The power management control ECU does not receive data from the brake booster with master cylinder assembly...
- U0293· The ECM does not receive data from the hybrid vehicle control computer assembly. · The brake booster with...
- U0293· The ECM does not receive data from the hybrid vehicle control computer assembly. · The brake booster with...
- U0293· The ECM does not receive data from the hybrid vehicle control computer assembly. · The brake booster with...
- U0293· The ECM does not receive data from the hybrid vehicle control computer assembly. · The brake booster with...
- U0293· The ECM does not receive data from the power management control ECU. · The brake booster with master...
- B1242· Short in RDAS to ground between the certification ECU (smart key ECU assembly) and the door control...
- B1242· Short in RDAS to ground between the certification ECU (smart key ECU assembly) and the door control...
- B1242· Short in RDAS to ground between the certification ECU (smart key ECU assembly) and the door control...
- B1242· Short in RDAS*1 or RDAM*2 to ground between the certification ECU (smart key ECU assembly) and the door...
- B2271When either of the following conditions is met (1-trip detection logic*): · The IG1 or IG2 circuit in the...
- B2271When either of the following conditions is met (1-trip detection logic*): · The IG1 or IG2 circuit in the...
- B2271When either of the following conditions is met (1-trip detection logic*): · The IG1 or IG2 circuit of the...
- B2271When either of the following conditions is met (1-trip detection logic*): · The IG1 or IG2 circuit of the...
- B2274Malfunction in the ACC circuit of the certification ECU (smart key ECU assembly)(1-trip detection logic*)....
- B2274Malfunction in the ACC circuit of the certification ECU (smart key ECU assembly)(1-trip detection logic*)....
- B2274Malfunction in the ACC relay circuit in the power management control ECU or in the external circuit (1-trip...
- B2274Malfunction in the ACC relay circuit in the power management control ECU or in the external circuit (1-trip...
- B2275Certification ECU (smart key ECU assembly) internal HV activation request output circuit malfunction (1-trip...
- B2275Power management control ECU internal HV activation request output circuit malfunction or external circuit...
- B2275Power management control ECU internal HV activation request output circuit malfunction or external circuit...
- B2277The water submersion detection circuit in the certification ECU (smart key ECU assembly) detects water...
- B2277The water submersion detection circuit in the certification ECU (smart key ECU assembly) detects water...
- B2277The water submersion detection circuit in the power management control ECU detects water submersion (1-trip...
- B2277The water submersion detection circuit in the power management control ECU detects water submersion (1-trip...
- B2282The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal...
- B2282The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal...
- B2282The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal...
- B2282The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal...
- B2283Vehicle speed signal malfunction detection : Excessive deceleration is detected (1-trip detection logic*)
- B2283Vehicle speed signal malfunction detection : Excessive deceleration is detected (1-trip detection logic*)
- B2283Vehicle speed signal malfunction detection : Excessive deceleration is detected (1-trip detection logic*)
- B2283Vehicle speed signal malfunction detection : Excessive deceleration is detected (1-trip detection logic*)
- B2284The brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection...
- B2284The brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection...
- B2284The brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection...
- B2285The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct...
- B2285The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct...
- B2285The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct...
- B2286READY signal error inside the power management control ECU (1-trip detection logic*)
- B2286READY signal error inside the power management control ECU (1-trip detection logic*)
- B27A1An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front...
- B27A1An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front...
- B27A1An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front...
- B27A1An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front...
- B27A2An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front...
- B27A2An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front...
- B27A2An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front...
- B27A2An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front...
- B27A5An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1...
- B27A5An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1...
- B27A5An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1...
- B27A6An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2...
- B27A6An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2...
- B27A6An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2...
- B27A7An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3...
- B27A7An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3...
- B27A7An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3...
- B27A8An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and...
- B27A8An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and...
- B27A8An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and...
- U0100CAN communication error between the certification ECU (smart key ECU assembly) and ECM (1-trip detection*)
- U0140CAN communication error between the certification ECU (smart key ECU assembly) and main body ECU (1-trip...
- U0140CAN communication error between the power management control ECU and main body ECU (1-trip detection*)
- U0142CAN communication error between the certification ECU (smart key ECU assembly) and main body ECU (1-trip...
- U0142CAN communication error between the certification ECU (smart key ECU assembly) and main body ECU (1-trip...
- U0155CAN communication error between the certification ECU (smart key ECU assembly) and combination meter assembly...
- U0155CAN communication error between the power management control ECU or certification ECU (smart key ECU...
- U0293CAN communication error between the certification ECU (smart key ECU assembly) and hybrid vehicle control ECU...
- U0293CAN communication error between the certification ECU (smart key ECU assembly) and power management control...
- U0293CAN communication error inside the power management control ECU (power control section - HV control section)....
- U0293CAN communication error inside the power management control ECU (power control section - HV control section)....
- B2784The transponder key amplifier coil built into the power switch is open (see below) or shorted (determined by...
- B2784The transponder key amplifier coil built into the power switch is open (see below) or shorted (determined by...
- B2784The transponder key amplifier coil built into the power switch is open (see below) or shorted (determined by...
- B278AA short to GND in the power supply of the transponder key amplifier of the power switch (VC5 - VC5) (1 trip...
- B278AA short to GND in the power supply of the transponder key amplifier of the power switch (VC5 - VC5) (1 trip...
- B278AA short to GND in the power supply of the transponder key amplifier of the power switch (VC5 - VC5) (1 trip...
- B2790An internal malfunction occurs in the ID code box (immobiliser code ECU) (EEPROM access malfunction) (1 trip...
- B2790An internal malfunction occurs in the ID code box (immobiliser code ECU) (EEPROM access malfunction) (1 trip...
- B2799Either condition is met (1 trip detection logic*): · A malfunction in the communication or communication...
- B2799Either condition is met (1 trip detection logic*): · A malfunction in the communication or communication...
- B2799Either condition is met (1 trip detection logic*): · A malfunction in the communication or communication...
- B279AThe communication line (IMI - EFIO) between the hybrid vehicle control ECU and ID code box (immobiliser code...
- B279AThe communication line (IMI - EFIO) between the power management control ECU and ID code box (immobiliser...
- B279CA hybrid vehicle control ECU that is incompatible with the engine immobiliser system is installed (1 trip...
- B279CA power management control ECU that is incompatible with the engine immobiliser system is installed (1 trip...
- B1500When IG voltage is 9.5 V or more and the following condition is detected: 1. Fuel sender gauge operation...
- B1500When IG voltage is 9.5 V or more and the following condition is detected: 1. Fuel sender gauge operation...
- B1500When IG voltage is 9.5 V or more and the following condition is detected: 1. Fuel sender gauge operation...
- B1503When IG voltage is 9.5 V or more and any of the following conditions is detected: 1. Engine coolant...
- B1504When the IG voltage is 9.5 V or more and power switch on (IG) and the following condition is detected: 1....
- B1507When IG voltage is 9.5 V or more and the following condition is detected: 1. Open in turn signal light circuit
- B1507When IG voltage is 9.5 V or more and the following condition is detected: 1. Open in turn signal light circuit
- B1507When IG voltage is 9.5 V or more and the following condition is detected: 1. Open in turn signal light circuit
- B1507When IG voltage is 9.5 V or more and the following condition is detected: 1. Open in turn signal light circuit
- B1508When IG voltage is 9.5 V or more and the following condition is detected: 1. Short in turn signal light...
- B1508When IG voltage is 9.5 V or more and the following condition is detected: 1. Short in turn signal light...
- B1508When IG voltage is 9.5 V or more and the following condition is detected: 1. Short in turn signal light...
- B1508When IG voltage is 9.5 V or more and the following condition is detected: 1. Short in turn signal light...
- U0100When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with ECM or...
- U0100When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with ECM or...
- U0100When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with ECM...
- U0100When IG voltage is 9.5 V or more and the following condition is detected: · No communication with ECM...
- U0129When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with brake...
- U0129When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with brake...
- U0129When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with skid...
- U0129When IG voltage is 9.5 V or more and the following condition is detected: No communication with brake booster...
- U0131When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with power...
- U0131When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with power...
- U0131When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with power...
- U0131When IG voltage is 9.5 V or more and the following condition is detected: No communication with power...
- U0142When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with main body...
- U0142When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with main body...
- U0142When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with main body...
- U0142When IG voltage is 9.5 V or more and the following condition is detected: No communication with main body ECU...
- U0151When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with airbag...
- U0151When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with airbag...
- U0151When IG voltage is 9.5 V or more and the following condition is detected: 1. No communication with airbag...
- U0151When IG voltage is 9.5 V or more and the following condition is detected: No communication with airbag sensor...
- B1000/31 Airbag sensor assembly malfunction
- B1000/31 Airbag sensor assembly malfunction
- B1610/13 · Front airbag sensor RH malfunction · Airbag sensor assembly malfunction
- B1610/13 · Front airbag sensor RH malfunction · Airbag sensor assembly malfunction
- B1610/13 · Front airbag sensor RH malfunction · Airbag sensor assembly malfunction
- B1610/13 · Front airbag sensor RH malfunction · Airbag sensor assembly malfunction
- B1612/83 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag...
- B1612/83 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1612/83 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1612/83 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1613/83 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag...
- B1613/83 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1613/83 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1613/83 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1615/14 · Front airbag sensor LH malfunction · Airbag sensor assembly malfunction
- B1615/14 · Front airbag sensor LH malfunction · Airbag sensor assembly malfunction
- B1615/14 · Front airbag sensor LH malfunction · Airbag sensor assembly malfunction
- B1615/14 · Front airbag sensor LH malfunction · Airbag sensor assembly malfunction
- B1617/84 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag...
- B1617/84 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1617/84 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1617/84 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1618/84 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag...
- B1618/84 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1618/84 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1618/84 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B161A/8A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B161A/8A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B161A/8A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1620/21 · Side airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1620/21 · Side airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1620/21 · Side airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1620/21 · Side airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1622/81 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1622/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1622/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1622/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1623/81 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1623/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1623/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1623/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1625/22 · Side airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1625/22 · Side airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1625/22 · Side airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1625/22 · Side airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1627/82 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1627/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1627/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1627/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1628/82 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1628/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1628/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1628/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1630/23 · Side No. 2 airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1630/23 · Side No. 2 airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1630/23 · Side No. 2 airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1630/23 · Side No. 2 airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1632/81 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1632/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1632/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1632/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1633/81 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1633/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1633/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1633/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1635/24 · Side No. 2 airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1635/24 · Side No. 2 airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1635/24 · Side No. 2 airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1635/24 · Side No. 2 airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1637/82 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1637/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1637/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1637/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1638/82 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1638/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1638/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1638/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1642/81 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1642/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1642/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1642/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1643/81 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1647/82 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1647/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1647/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1647/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1648/82 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1650/32 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the occupant...
- B1656/38 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the seat belt buckle...
- B1660/43 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the passenger airbag...
- B1690/15 · Door side airbag sensor RH malfunction · Airbag sensor assembly malfunction
- B1692/81 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1693/81 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1695/16 · Door side airbag sensor LH malfunction · Airbag sensor assembly malfunction
- B1697/82 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1698/82 · The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision...
- B1800/51 · The airbag sensor assembly detects a line short in the driver side squib circuit during the primary check....
- B1800/51 · The airbag sensor assembly receives a line short circuit signal in the driver side squib circuit during...
- B1800/51 · The airbag sensor assembly receives a line short circuit signal in the driver side squib circuit during...
- B1800/51 · The airbag sensor assembly receives a line short circuit signal in the driver side squib circuit during...
- B1801/51 · The airbag sensor assembly detects an open in the driver side squib circuit. · Spiral cable with sensor...
- B1801/51 · The airbag sensor assembly receives an open circuit signal in the driver side squib circuit. · Spiral cable...
- B1801/51 · The airbag sensor assembly receives an open circuit signal in the driver side squib circuit. · Spiral cable...
- B1801/51 · The airbag sensor assembly receives an open circuit signal in the driver side squib circuit. · Spiral cable...
- B1802/51 · The airbag sensor assembly detects a short to ground in the driver side squib circuit. · Spiral cable with...
- B1802/51 · The airbag sensor assembly receives a short circuit to ground signal in the driver side squib circuit. ·...
- B1802/51 · The airbag sensor assembly receives a short circuit to ground signal in the driver side squib circuit. ·...
- B1802/51 · The airbag sensor assembly receives a short circuit to ground signal in the driver side squib circuit. ·...
- B1803/51 · The airbag sensor assembly detects a short to B+ in the driver side squib circuit. · Spiral cable with...
- B1803/51 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side squib circuit. · Spiral...
- B1803/51 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side squib circuit. · Spiral...
- B1803/51 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side squib circuit. · Spiral...
- B1805/52 · The airbag sensor assembly detects a line short in the front passenger side squib circuit during the...
- B1805/52 · The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit...
- B1805/52 · The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit...
- B1805/52 · The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit...
- B1806/52 · The airbag sensor assembly detects an open in the front passenger side squib circuit. · Front passenger...
- B1806/52 · The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit. ·...
- B1806/52 · The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit. ·...
- B1806/52 · The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit. ·...
- B1807/52 · The airbag sensor assembly detects a short to ground in the front passenger side squib circuit. · Front...
- B1807/52 · The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib...
- B1807/52 · The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib...
- B1807/52 · The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib...
- B1808/52 · The airbag sensor assembly detects a short to B+ in the front passenger side squib circuit. · Front...
- B1808/52 · The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit....
- B1808/52 · The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit....
- B1808/52 · The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit....
- B1810/53 · The airbag sensor assembly detects a line short in the driver side squib 2nd step circuit during the...
- B1811/53 · The airbag sensor assembly detects an open in the driver side squib 2nd step circuit. · Spiral cable with...
- B1812/53 · The airbag sensor assembly detects a short to ground in the driver side squib 2nd step circuit. · Spiral...
- B1813/53 · The airbag sensor assembly detects a short to B+ in the driver side squib 2nd step circuit. · Spiral cable...
- B1815/54 · The airbag sensor assembly detects a line short in the front passenger side squib 2nd step circuit during...
- B1816/54 · The airbag sensor assembly detects an open in the front passenger side squib 2nd step circuit. · Front...
- B1817/54 · The airbag sensor assembly detects a short to ground in the front passenger side squib 2nd step circuit. ·...
- B1818/54 · The airbag sensor assembly detects a short to B+ in the front passenger side squib 2nd step circuit. ·...
- B181A/7A · The airbag sensor assembly detects a line short in the passenger side airbag variable vent hole squib...
- B181B/7A · The airbag sensor assembly detects an open in the passenger side airbag variable vent hole squib circuit. ·...
- B181C/7A · The airbag sensor assembly detects a short to ground in the passenger side airbag variable vent hole squib...
- B181D/7A · The airbag sensor assembly detects a short to B+ in the passenger side airbag variable vent hole squib...
- B1820/55 · The airbag sensor assembly detects a line short in the side squib RH circuit during the primary check. ·...
- B1820/55 · The airbag sensor assembly receives a line short circuit signal in the side squib RH circuit during primary...
- B1820/55 · The airbag sensor assembly receives a line short circuit signal in the side squib RH circuit during primary...
- B1820/55 · The airbag sensor assembly receives a line short circuit signal in the side squib RH circuit during primary...
- B1821/55 · The airbag sensor assembly detects an open in the side squib RH circuit. · Side squib RH malfunction ·...
- B1821/55 · The airbag sensor assembly receives an open circuit signal in the side squib RH circuit. · Side squib RH...
- B1821/55 · The airbag sensor assembly receives an open circuit signal in the side squib RH circuit. · Side squib RH...
- B1821/55 · The airbag sensor assembly receives an open circuit signal in the side squib RH circuit. · Side squib RH...
- B1822/55 · The airbag sensor assembly detects a short to ground in the side squib RH circuit. · Side squib RH...
- B1822/55 · The airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit. · Side...
- B1822/55 · The airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit. · Side...
- B1822/55 · The airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit. · Side...
- B1823/55 · The airbag sensor assembly detects a short to B+ in the side squib RH circuit. · Side squib RH malfunction...
- B1823/55 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit. · Side squib...
- B1823/55 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit. · Side squib...
- B1823/55 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit. · Side squib...
- B1825/56 · The airbag sensor assembly detects a line short in the side squib LH circuit during the primary check. ·...
- B1825/56 · The airbag sensor assembly receives a line short circuit signal in the side squib LH circuit during primary...
- B1825/56 · The airbag sensor assembly receives a line short circuit signal in the side squib LH circuit during primary...
- B1825/56 · The airbag sensor assembly receives a line short circuit signal in the side squib LH circuit during primary...
- B1826/56 · The airbag sensor assembly detects an open in the side squib LH circuit. · Side squib LH malfunction ·...
- B1826/56 · The airbag sensor assembly receives an open circuit signal in the side squib LH circuit. · Side squib LH...
- B1826/56 · The airbag sensor assembly receives an open circuit signal in the side squib LH circuit. · Side squib LH...
- B1826/56 · The airbag sensor assembly receives an open circuit signal in the side squib LH circuit. · Side squib LH...
- B1827/56 · The airbag sensor assembly detects a short to ground in the side squib LH circuit. · Side squib LH...
- B1827/56 · The airbag sensor assembly receives a short circuit to ground signal in the side squib LH circuit. · Side...
- B1827/56 · The airbag sensor assembly receives a short circuit to ground signal in the side squib LH circuit. · Side...
- B1827/56 · The airbag sensor assembly receives a short circuit to ground signal in the side squib LH circuit. · Side...
- B1828/56 · The airbag sensor assembly detects a short to B+ in the side squib LH circuit. · Side squib LH malfunction...
- B1828/56 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib LH circuit. · Side squib...
- B1828/56 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib LH circuit. · Side squib...
- B1828/56 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib LH circuit. · Side squib...
- B1830/57 · The airbag sensor assembly detects a line short in the curtain shield squib RH circuit during the primary...
- B1830/57 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib RH circuit...
- B1830/57 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib RH circuit...
- B1830/57 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib RH circuit...
- B1831/57 · The airbag sensor assembly detects an open in the curtain shield squib RH circuit. · Curtain shield squib...
- B1831/57 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib RH circuit. ·...
- B1831/57 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib RH circuit. ·...
- B1831/57 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib RH circuit. ·...
- B1832/57 · The airbag sensor assembly detects a short to ground in the curtain shield squib RH circuit. · Curtain...
- B1832/57 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib RH...
- B1832/57 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib RH...
- B1832/57 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib RH...
- B1833/57 · The airbag sensor assembly detects a short to B+ in the curtain shield squib RH circuit. · Curtain shield...
- B1833/57 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit. ·...
- B1833/57 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit. ·...
- B1833/57 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit. ·...
- B1835/58 · The airbag sensor assembly detects a line short in the curtain shield squib LH circuit during the primary...
- B1835/58 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit...
- B1835/58 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit...
- B1835/58 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit...
- B1836/58 · The airbag sensor assembly detects an open in the curtain shield squib LH circuit. · Curtain shield squib...
- B1836/58 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit. ·...
- B1836/58 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit. ·...
- B1836/58 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit. ·...
- B1837/58 · The airbag sensor assembly detects a short to ground in the curtain shield squib LH circuit. · Curtain...
- B1837/58 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH...
- B1837/58 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH...
- B1837/58 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH...
- B1838/58 · The airbag sensor assembly detects a short to B+ in the curtain shield squib LH circuit. · Curtain shield...
- B1838/58 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit. ·...
- B1838/58 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit. ·...
- B1838/58 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit. ·...
- B1860/64 · The airbag sensor assembly detects a line short in the driver side knee airbag squib circuit during the...
- B1860/64 · The airbag sensor assembly receives a line short circuit signal in the driver side knee airbag squib...
- B1860/64 · The airbag sensor assembly receives a line short circuit signal in the driver side knee airbag squib...
- B1860/64 · The airbag sensor assembly receives a line short circuit signal in the driver side knee airbag squib...
- B1861/64 · The airbag sensor assembly detects an open in the driver side knee airbag squib circuit. · Driver side knee...
- B1861/64 · The airbag sensor assembly receives an open circuit signal in the driver side knee airbag squib circuit. ·...
- B1861/64 · The airbag sensor assembly receives an open circuit signal in the driver side knee airbag squib circuit. ·...
- B1861/64 · The airbag sensor assembly receives an open circuit signal in the driver side knee airbag squib circuit. ·...
- B1862/64 · The airbag sensor assembly detects a short to ground in the driver side knee airbag squib circuit. · Driver...
- B1862/64 · The airbag sensor assembly receives a short circuit to ground signal in the driver side knee airbag squib...
- B1862/64 · The airbag sensor assembly receives a short circuit to ground signal in the driver side knee airbag squib...
- B1862/64 · The airbag sensor assembly receives a short circuit to ground signal in the driver side knee airbag squib...
- B1863/64 · The airbag sensor assembly detects a short to B+ in the driver side knee airbag squib circuit. · Driver...
- B1863/64 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side knee airbag squib...
- B1863/64 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side knee airbag squib...
- B1863/64 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side knee airbag squib...
- B1870/66 · The airbag sensor assembly detects a line short in the driver side front seat cushion squib circuit during...
- B1871/66 · The airbag sensor assembly detects an open in the driver side front seat cushion squib circuit. · Driver...
- B1872/66 · The airbag sensor assembly detects a short to ground in the driver side front seat cushion squib circuit. ·...
- B1873/66 · The airbag sensor assembly detects a short to B+ in the driver side front seat cushion squib circuit. ·...
- B1875/67 · The airbag sensor assembly detects a line short in the passenger side front seat cushion squib circuit...
- B1876/67 · The airbag sensor assembly detects an open in the passenger side front seat cushion squib circuit. ·...
- B1877/67 · The airbag sensor assembly detects a short to ground in the passenger side front seat cushion squib...
- B1878/67 · The airbag sensor assembly detects a short to B+ in the passenger side front seat cushion squib circuit. ·...
- B1900/73 · The airbag sensor assembly detects a line short in the front pretensioner squib RH circuit during the...
- B1900/73 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib RH circuit...
- B1900/73 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib RH circuit...
- B1900/73 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib RH circuit...
- B1901/73 · The airbag sensor assembly detects an open in the front pretensioner squib RH circuit. · Front pretensioner...
- B1901/73 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib RH circuit. ·...
- B1901/73 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib RH circuit. ·...
- B1901/73 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib RH circuit. ·...
- B1902/73 · The airbag sensor assembly detects a short to ground in the front pretensioner squib RH circuit. · Front...
- B1902/73 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib RH...
- B1902/73 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib RH...
- B1902/73 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib RH...
- B1903/73 · The airbag sensor assembly detects a short to B+ in the front pretensioner squib RH circuit. · Front...
- B1903/73 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib RH...
- B1903/73 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib RH...
- B1903/73 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib RH...
- B1905/74 · The airbag sensor assembly detects a line short in the front pretensioner squib LH circuit during the...
- B1905/74 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib LH circuit...
- B1905/74 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib LH circuit...
- B1905/74 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib LH circuit...
- B1906/74 · The airbag sensor assembly detects an open in the front pretensioner squib LH circuit. · Front pretensioner...
- B1906/74 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib LH circuit. ·...
- B1906/74 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib LH circuit. ·...
- B1906/74 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib LH circuit. ·...
- B1907/74 · The airbag sensor assembly detects a short to ground in the front pretensioner squib LH circuit. · Front...
- B1907/74 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib LH...
- B1907/74 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib LH...
- B1907/74 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib LH...
- B1908/74 · The airbag sensor assembly detects a short to B+ in the front pretensioner squib LH circuit. · Front...
- B1908/74 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib LH...
- B1908/74 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib LH...
- B1908/74 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib LH...
- B1771· The occupant detection ECU detects a line short, short to ground or B+, or an open in the passenger side...
- B1780· The occupant detection ECU detects a line short, short to ground or B+, or an open in the front occupant...
- B1782· The occupant detection ECU detects a line short, short to ground or B+, or an open in the rear occupant...
- B1785· Front occupant classification sensor LH sensed large load · Separate type front seat cushion spring...
- B1787· Rear occupant classification sensor LH sensed large load · Separate type front seat cushion spring assembly...
- B1790· The occupant detection ECU detects a line short, short to ground or B+, or an open in the airbag sensor...
- B1793· The occupant detection ECU detects a line short, short to ground or B+ in the occupant classification...
- B1794· The occupant detection ECU receives an open circuit signal in the occupant detection ECU auxiliary battery...
- B1795Occupant detection ECU malfunction
- B1796Occupant detection ECU malfunction
- B1411/11 Open or short in room temperature sensor (cooler thermistor) circuit
- B1412/12 Open or short in ambient temperature sensor (thermistor assembly) circuit
- B1412/12 Open or short in ambient temperature sensor (thermistor assembly) circuit
- B1413/13 Open or short in evaporator temperature sensor (No. 1 cooler thermistor) circuit
- B1423/23 · Open or short in air conditioning pressure sensor circuit · Refrigerant pressure on the high pressure side...
- B1423/23 · Open or short in air conditioning pressure sensor circuit · Refrigerant pressure on the high pressure side...
- B1441/41 Air mix damper position sensor value does not change even though air conditioning amplifier assembly operates...
- B1441/41 Air mix damper position sensor value does not change even though air conditioning amplifier assembly operates...
- B1441/41 Air mix damper position sensor value does not change even though air conditioning amplifier assembly operates...
- B1442/42 Air inlet damper position sensor value does not change even though air conditioning amplifier assembly...
- B1443/43 Air outlet damper position sensor value does not change even though the air conditioning amplifier assembly...
- B1443/43 Air outlet damper position sensor value does not change even though the air conditioning amplifier assembly...
- B1443/43 Air outlet damper position sensor value does not change even though the air conditioning amplifier assembly...
- B1471/71 · Open or short in A/C inverter high voltage power resource system · The boost inverter is broken or...
- B1471/71 · Open or short in A/C inverter high voltage power resource system · The boost inverter is broken or...
- B1472/72 Open or short in A/C inverter high voltage output system
- B1472/72 Open or short in A/C inverter high voltage output system
- B1473/73 Open or short in A/C inverter start-up signal system
- B1473/73 Open or short in A/C inverter start-up signal system
- B1474/74 A/C inverter malfunction
- B1474/74 A/C inverter malfunction
- B1475/75 Temperature of the inverter is outside the specified range (temperature is too high), or there is an open or...
- B1475/75 Temperature of the inverter is outside the specified range (temperature is too high), or there is an open or...
- B1476/76 Motor rotation load while the compressor is operating is too large or too small.
- B1476/76 Motor rotation load while the compressor is operating is too large or too small.
- B1477/77 An open or short to ground in the inverter control power voltage circuit.
- B1477/77 An open or short to ground in the inverter control power voltage circuit.
- B1497/97 Error or open in communication line
- B1497/97 Error or open in communication line
- B1498/98 · Communication line error or open between the hybrid vehicle control ECU and compressor with motor assembly....
- B1498/98 · Communication line error or open between the power management control ECU and compressor with motor...
- B14A2Short in cooler thermistor (solar sensor) circuit
- B14A2Short in cooler thermistor (solar sensor) circuit
- B14B2Lost communication with the air conditioning panel (heater control switch board).
- B14B2Lost communication with the air conditioning panel (heater control switch board).
- B14B8When the following conditions is detected using the refrigerant shortage check in normal operation: The...
- B14B8When the following conditions is detected using the refrigerant shortage check in normal operation: The...
- P0AA6611 High voltage system insulation malfunction
- P0AA6611 High voltage system insulation malfunction
- U0101No communication with TCM
- U0101No communication with TCM
- U0142No communication with main body ECU
- U0142No communication with main body ECU
- U0155No communication with combination meter
- U0155No communication with combination meter
- U0293No communication with HV ECU
- U0293No communication with HV ECU
- B2311Either condition is met: (a) Power window regulator motor assembly malfunctions (b) When ECU in power window...
- B2312· Power window regulator master switch assembly (for driver door) stuck · Power window regulator master...
- B2312· Power window regulator master switch assembly (for driver door) stuck · Power window regulator master...
- B2313· Power window regulator motor assembly not initialized · Power window regulator motor assembly malfunctions...
- B1244· Malfunction in automatic light control sensor · Open or short in automatic light control sensor circuit
- B2430LED headlight LH circuit malfunction
- B2430LED headlight LH circuit malfunction
- B2430LED headlight LH circuit malfunction
- B2430LED headlight LH circuit malfunction
- B2431LED headlight RH circuit malfunction
- B2431LED headlight RH circuit malfunction
- B2431LED headlight RH circuit malfunction
- B2431LED headlight RH circuit malfunction
- B2415Vehicle Speed Sensor Malfunction
- B2416Height Control Sensor Malfunction
- B2416· Malfunction in rear height control sensor sub-assembly · Open or short in rear height control sensor...
- B2416· Malfunction in rear height control sensor sub-assembly · Open or short in rear height control sensor...
- B241ARear Height Control Sensor
- B241A· Malfunction in rear height control sensor sub-assembly · Open or short in rear height control sensor...
- B241A· Malfunction in rear height control sensor sub-assembly · Open or short in rear height control sensor...
- B2420HL AutoLeveling ECU Failure
- B2420Malfunction of headlight leveling ECU assembly
- B2420Malfunction of headlight leveling ECU assembly
- B2450Initialization has not been Performed
- B2450Initialization of the headlight leveling ECU assembly has not been performed
- B2451Vehicle Specifications have not been Stored
- B2451Vehicle specifications have not been stored
- B2452Height Control Sensor Data Out of Range When Initializing
- B2452Vehicle condition not specified when initializing
- B2453The headlight leveling ECU assembly for another destination is installed on the vehicle
- B2453Variation Error
- U0100Lost Communication with ECM / PCM "A"
- U0129Lost Communication with Brake System Control Module
- U0142Lost Communication with Body Control Module "B"
- U1000CAN Communication Failure (Message Registry)
- B1350Either of the following conditions is met: · When sound output voltage is being monitored by the ECU, with...
- B1350Speaker Circuit
- U0129Lost Communication with Brake System Control Module
- U0140Lost Communication with Body Control Module
- U0293Lost Communication with Hybrid/EV Powertrain Control Module
Common jobs · 1NZ-FXE (10)
- Read / clear codes
- Valve clearance: adjustment
- Water pump: removal · installation
- Thermostat: inspection · removal · installation
- Radiator: on-vehicle inspection
- Fuel pump: inspection · removal · disassembly · reassembly · installation
- Injectors: inspection
- Throttle body: on-vehicle inspection · inspection · removal
- Cylinder head: inspection · replacement · disassembly · reassembly
- Engine assembly: inspection
Common jobs · chassis & body (5)
- Coolant: on-vehicle inspection
- Front brakes: inspection · installation
- Rear brakes: inspection · disassembly · reassembly
- Brake fluid: on-vehicle inspection · replacement · bleeding
- Front drive shaft: inspection
Repair Manual
General272 documents
Engine / Hybrid System1207 documents
Drivetrain103 documents
Suspension132 documents
Brake318 documents
Steering144 documents
Audio / Visual / Telematics98 documents
Power Source / Network181 documents
Vehicle Interior1244 documents
Vehicle Exterior768 documents
New Car Features
General25 documents
Engine / Hybrid System84 documents
Drivetrain9 documents
Suspension22 documents
Brake17 documents
Steering12 documents
Audio / Visual / Telematics12 documents
Power Source / Network24 documents
Vehicle Interior96 documents
Vehicle Exterior67 documents