Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR
BM2170E _01 Vehicle Exterior _057059 BODY WELD POINT _0278244 CENTER BODY PILLAR F

BODY WELD POINT  CENTER BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K104258

Weld work for 980 MPa ultra high strength steel

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

*1: When welding 2 panels together including 980 MPa ultra high strength steel.

Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 18 Cyc. (0.30 Sec.)
Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


*2: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)

2.

*3: Bolts.

3.

*4 is reused.


U159845E02
3.208,7.26 3.208,7.021 false 0.75,6.021 0.927,6.021 0.927,6.021 1.417,6.521 false 3.292,1.302 3.448,1.5 0.156,0.198 10 false 4 6.125,7.313 6.281,7.51 0.156,0.198 10 false 3 2.99,1.74 3.146,1.938 0.156,0.198 10 false 5 3.563,2.865 3.875,3.063 0.313,0.198 10 false 19 4.573,1.948 4.729,2.146 0.156,0.198 10 false 4 1.083,1.031 1.24,1.229 0.156,0.198 10 false 1 4.448,1.729 4.604,1.927 0.156,0.198 10 false 3 5.229,6.26 5.385,6.458 0.156,0.198 10 false 2 6.375,0.604 6.969,0.813 0.594,0.208 10 false 30 (1.18) 0.76,4.438 1.354,4.646 0.594,0.208 10 false 30 (1.18) 2.438,9.417 2.594,9.615 0.156,0.198 10 false 2 1.344,9.427 1.5,9.625 0.156,0.198 10 false 2 2,7.229 2.156,7.427 0.156,0.198 10 false 2 1.177,7.229 1.333,7.427 0.156,0.198 10 false 2 1.875,8.354 2.031,8.552 0.156,0.198 10 false 4 2.188,6.229 2.76,6.427 0.573,0.198 10 true 20 (0.79) 1.969,6.979 2.688,7.188 0.719,0.208 10 false 260 (10.24) 0.427,7.042 1.052,7.26 0.625,0.219 10 false 200 (7.87) 3.135,7.271 3.323,7.469 0.188,0.198 10 false *3 0.604,5.917 0.771,6.094 0.167,0.177 10 false *4 4.01,9.25 4.604,9.458 0.594,0.208 10 true 40 (1.57) 6.448,9.24 7.042,9.448 0.594,0.208 10 false 40 (1.57) 0.146,9.438 0.698,9.667 0.552,0.229 10 false mm (in.) 3.271,6.938 3.5,7.135 0.229,0.198 10 false x3

INSTALLATION


Symbol meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram)

3.

*3: Bolts.

4.

Follow the welding conditions when welding *1 and *2 to assure sufficient weld strength. (See the introduction)

5.

Before temporarily installing the new parts, weld the center body pillar reinforcement sub-assembly and center body pillar sub-assembly inner with the standard number of welding points.

6.

After welding the center body pillar reinforcement sub-assembly and center body pillar sub-assembly inner to the vehicle side, install the rocker panel outer and *4.

7.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

8.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

9.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K135726E01
2.26,1.042 2.26,0.656 2.26,0.656 2.396,0.656 false 4.854,1.833 5.104,1.833 false 2.448,0.563 6.333,0.792 3.885,0.229 10 false CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY 2.844,1.74 4.813,1.979 1.969,0.24 10 false CENTER BODY PILLAR INNER 5.729,3.313 6.427,3.552 0.698,0.24 10 false 110 (4.33) 0.719,3.125 1.333,3.375 0.615,0.25 10 false 30 (1.18) 0.292,9.49 0.885,9.75 0.594,0.26 10 false mm (in.) 2.948,8.75 3.26,8.948 0.313,0.198 10 false *1 2.417,7.198 2.729,7.396 0.313,0.198 10 false *1 4.073,7.135 4.385,7.333 0.313,0.198 10 false *1

K135727E01
0.26,9.396 1.51,9.646 1.25,0.25 4.458,8.021 5.208,8.271 0.75,0.25 4.823,7.813 4.823,7.563 false 4.75,7.833 5.063,8.031 0.313,0.198 10 false *3 4.51,8.063 5.26,8.302 0.75,0.24 10 false 12 (122, 9) 0.281,9.438 2.646,9.698 2.365,0.26 10 false N*m (kgf*cm, ft.*lbf) : Specified torque

K135728E01
2.896,6.156 3,6.156 3,6.156 3.563,7.063 false 3.708,1.583 3.708,0.76 3.708,0.76 3.854,0.76 false 3.906,0.667 5.583,0.906 1.677,0.24 10 false ROCKER PANEL OUTER 3.083,3.948 3.396,4.146 0.313,0.198 10 false *2 2.74,6.063 3.052,6.26 0.313,0.198 10 false *4 2.49,2.75 2.802,2.948 0.313,0.198 10 false *2 2.688,1.802 3,2 0.313,0.198 10 false *2 4.083,1.885 4.396,2.083 0.313,0.198 10 false *2 4.344,2.583 4.656,2.781 0.313,0.198 10 false *2