Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR › from 2017.06
BM2170E _01 Vehicle Exterior _057059 BODY PANEL _0278243 FRONT BODY PILLAR F

BODY PANEL  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 1)  


K141794

With the cowl top side upper panel removed.


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

After removing the front body pillar outer, remove the *1.


K141821E04
2.104,4.781 2.385,4.781 2.385,4.781 2.583,3.875 false 0.177,0.375 0.729,0.615 0.552,0.24 12 false LH: 4.667,5.531 6.354,5.729 1.688,0.198 10 false 300 (11.81) 0.198,9.521 1.427,9.719 1.229,0.198 10 false mm (in.) 0.177,0.115 2.01,0.354 1.833,0.24 12 false for Type B: 0.104,4.688 2.052,4.865 1.948,0.177 10 false FRONT BODY PILLAR OUTER

K141822E02
0.677,4.146 1,4.146 1,4.146 1.427,3.281 false 0.5,4.042 0.813,4.24 0.313,0.198 10 false *1

INSTALLATION


Symbol meaning
K108818

Remove Weld Points
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


5.

When welding *1, make a hole on a new part for plug welding and weld the panel with the panel.

6.

After welding the *2 to the vehicle side, install the front body pillar outer.

7.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

8.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

9.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K141823E02
1.833,0.854 2.219,0.333 2.219,0.333 2.552,0.333 false 3.448,5.073 3.677,5.073 3.677,5.073 3.938,4.583 false 4.708,7.563 5.479,7.76 0.771,0.198 10 false 15 (0.59) 4.948,8.677 5.719,8.875 0.771,0.198 10 false 15 (0.59) 0.198,9.552 1.427,9.75 1.229,0.198 10 false mm (in.) 0.125,0.333 0.583,0.531 0.458,0.198 12 false LH: 2.625,0.26 6.594,0.448 3.969,0.188 10 false FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER 3.271,4.969 3.583,5.167 0.313,0.198 10 false *2 0.146,0.094 2.167,0.333 2.021,0.24 12 false for Type B:

K141824E02
3.667,1.802 3.875,0.573 3.875,0.573 4.198,0.573 false 4.26,0.458 6.25,0.646 1.99,0.188 10 false FRONT BODY PILLAR OUTER