Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR › from 2017.06
BM2170E _01 Vehicle Exterior _057059 BODY PANEL _0278243 FRONT BODY PILLAR F

BODY PANEL  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 2)  


K141763

With the cowl top side upper panel and roof panel removed.(LH) With the cowl top side upper panel removed.(RH)


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


REMOVAL POINT (for Type A:)
1.

*1 is reused.


REMOVAL POINT (for Type B: LH)
1.

*2 is reused.

2.

After removing the front body pillar outer, remove the front pillar reinforcement sub-assembly lower.

3.

After removing the front pillar reinforcement sub-assembly lower, remove the front body pillar sub-assembly inner.


REMOVAL POINT (for Type B: RH)
1.

*3 is reused.


K141931E01
3.375,6.021 4.135,6.979 4.135,6.979 4.344,6.979 false 0.229,0.219 2.25,0.458 2.021,0.24 12 false for Type A: 5.146,7.438 6.677,7.635 1.531,0.198 10 false 200 (7.87) 5.125,7.781 6.656,7.979 1.531,0.198 10 false 150 (5.91) 0.177,9.479 1.406,9.677 1.229,0.198 10 false mm (in.) 4.677,1.24 6.208,1.438 1.531,0.198 10 false 150 (5.91) 4.396,6.875 4.708,7.073 0.313,0.198 10 false *1

K141932E01
0.208,9.521 1.438,9.719 1.229,0.198 10 false mm (in.) 3.375,6.542 4.906,6.74 1.531,0.198 10 false 100 (3.94)

K141825E02
3.677,0.708 4.115,0.708 4.115,0.708 4.365,1.635 false 2.188,5.458 2.417,5.458 2.417,5.458 2.729,4.667 false 0.24,0.521 0.698,0.719 0.458,0.198 12 false LH: 3.51,0.625 3.823,0.823 0.313,0.198 10 false *2 0.24,9.51 1.469,9.708 1.229,0.198 10 false mm (in.) 4,1.948 4.698,2.115 0.698,0.167 10 false 130 (5.12) 0.198,5.354 2.167,5.552 1.969,0.198 10 false FRONT BODY PILLAR OUTER 0.24,0.219 2.26,0.458 2.021,0.24 12 false for Type B:

K141826

K141827E02
1.813,0.781 1.573,0.781 1.573,0.781 1.208,1.885 false 1.875,0.667 5.75,0.885 3.875,0.219 10 false FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER

K141828

K141829E02
2.031,3.604 2.365,4.031 2.365,4.031 2.615,4.031 false 0.219,9.521 1.448,9.719 1.229,0.198 10 false mm (in.) 3.229,2.875 4.604,3.073 1.375,0.198 10 false 20 (0.79) 3.667,7.531 5.042,7.729 1.375,0.198 10 false 115 (4.53) 2.656,3.927 5.667,4.104 3.01,0.177 10 false FRONT BODY PILLAR SUB-ASSEMBLY INNER

K141858E02
3.427,8.229 4.802,8.427 1.375,0.198 10 false 65 (2.56) 0.271,9.458 1.5,9.656 1.229,0.198 10 false mm (in.)

K141764E02
1.615,6.958 1.896,6.958 1.896,6.958 2.729,6 false 4.583,1.229 6.115,1.427 1.531,0.198 10 false 150 (5.91) 2.917,7.458 4.448,7.656 1.531,0.198 10 false 200 (7.87) 2.906,7.802 4.438,8 1.531,0.198 10 false 150 (5.91) 0.25,0.479 0.708,0.677 0.458,0.198 12 false RH: 0.271,9.469 1.5,9.667 1.229,0.198 10 false mm (in.) 1.448,6.854 1.76,7.052 0.313,0.198 10 false *3 0.271,0.229 1.958,0.427 1.688,0.198 12 false for Type B:

K141765E02
5.01,6.573 6.542,6.771 1.531,0.198 10 false 100 (3.94) 0.25,9.469 1.479,9.667 1.229,0.198 10 false mm (in.)

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT (for Type A:)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


5.

Before temporarily installing the new parts, weld the rocker reinforce sub-assembly outer, front body pillar sub-assembly inner and front pillar reinforcement sub-assembly lower with the standard number of welding points.

6.

When welding *1, make a hole on a new part for plug welding and weld the panel with the panel.

7.

After welding the rocker reinforce sub-assembly outer, front body pillar sub-assembly inner and front pillar reinforcement sub-assembly lower to the vehicle side, install the front body pillar outer and *2.

8.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

9.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

10.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


INSTALLATION POINT (for Type B: LH)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


5.

When welding *1, make a hole on a new part for plug welding and weld the panel with the panel.

6.

After welding the front body pillar sub-assembly inner to the vehicle side, install the front pillar reinforcement sub-assembly lower.

7.

After welding the front pillar reinforcement sub-assembly lower to the vehicle side, install the front body pillar outer and *3.

8.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

9.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

10.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


INSTALLATION POINT (for Type B: RH)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


5.

Before temporarily installing the new parts, weld the rocker reinforce sub-assembly outer, front body pillar sub-assembly inner and front pillar reinforcement sub-assembly lower with the standard number of welding points.

6.

When welding *1, make a hole on a new part for plug welding and weld the panel with the panel.

7.

After welding the rocker reinforce sub-assembly outer, front body pillar sub-assembly inner and front pillar reinforcement sub-assembly lower to the vehicle side, install the front body pillar outer and *4.

8.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

9.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

10.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K141933E01
2.094,2.26 1.823,2.26 1.823,2.26 1.823,1.573 false 1.417,2.427 1.146,2.427 1.146,2.427 1.625,3.583 false 0.969,5.521 0.729,5.521 0.729,5.521 1.719,6.5 false 0.146,0.135 2.167,0.375 2.021,0.24 12 false for Type A: 2.083,0.604 3.458,0.802 1.375,0.198 10 false 50 (1.97) 2.156,2.146 5.323,2.323 3.167,0.177 10 false ROCKER REINFORCE SUB-ASSEMBLY OUTER 1.479,2.365 4.646,2.542 3.167,0.177 10 false FRONT BODY PILLAR SUB-ASSEMBLY INNER 1.021,5.427 4.969,5.594 3.948,0.167 10 false FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER 2.729,3.615 4.104,3.813 1.375,0.198 10 false 30 (1.97) 4.958,5.813 6.333,6.01 1.375,0.198 10 false 10 (0.39) 6.167,7.094 6.76,7.281 0.594,0.188 10 false 15 (0.59) 6.094,8.344 6.688,8.531 0.594,0.188 10 false 15 (0.59) 0.208,9.542 1.438,9.74 1.229,0.198 10 false mm (in.)

K141934E01
4.594,7.26 5.969,7.458 1.375,0.198 10 false 10 (0.39) 4.469,9.063 5.844,9.26 1.375,0.198 10 false 15 (0.59) 5.823,9.083 6.594,9.271 0.771,0.188 10 false 15 (0.59) 0.219,9.479 1.448,9.677 1.229,0.198 10 false mm (in.)

K141935E01
4.75,5.698 4.573,4.802 4.573,4.802 4.24,4.802 false 6.094,8.656 5.802,8.656 5.802,8.656 5.135,8.01 false 2.26,4.719 5.781,4.917 3.521,0.198 10 false FRONT BODY PILLAR OUTER 6.135,8.542 6.448,8.74 0.313,0.198 10 false *2

K141830E02
2.052,3.781 2.313,4.063 2.313,4.063 2.583,4.063 false 0.25,0.51 0.708,0.708 0.458,0.198 12 false LH: 2.646,3.969 5.667,4.156 3.021,0.188 10 false FRONT BODY PILLAR SUB-ASSEMBLY INNER 0.281,0.25 1.969,0.448 1.688,0.198 12 false for Type B:

K141859

K141831E02
2.208,1.427 2.625,0.802 2.625,0.802 2.979,0.802 false 3.021,0.708 6.885,0.885 3.865,0.177 10 false FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER

K141832E02
4.531,7 5.906,7.198 1.375,0.198 10 false 15 (0.59) 4.823,8.104 6.198,8.302 1.375,0.198 10 false 15 (0.59) 0.313,9.448 1.542,9.646 1.229,0.198 10 false mm (in.)

K141833E02
3.979,3.698 3.667,2.719 3.667,2.719 3.354,2.719 false 5.344,3.281 5.031,2.302 5.031,2.302 4.719,2.302 false 4.563,2.208 5.021,2.406 0.458,0.198 10 false *3 1.375,2.604 3.302,2.802 1.927,0.198 10 false FRONT BODY PILLAR OUTER

K141834

K141766E02
5.083,2.25 5.344,2.25 5.344,2.25 5.344,1.583 false 1.208,6.115 0.76,5.552 0.76,5.552 1,5.552 false 2.677,3.281 2.896,2.656 2.896,2.656 3.156,2.656 false 4.583,0.625 5.958,0.823 1.375,0.198 10 false 50 (1.97) 1.896,3.604 3.271,3.802 1.375,0.198 10 false 30 (1.18) 5.135,5.802 6.51,6 1.375,0.198 10 false 10 (0.39) 4.125,7.094 5.5,7.292 1.375,0.198 10 false 15 (0.59) 4.365,8.323 5.74,8.521 1.375,0.198 10 false 15 (0.59) 0.25,0.563 0.708,0.76 0.458,0.198 12 false RH: 1.042,5.469 4.917,5.635 3.875,0.167 10 false FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER 1.979,2.156 5.083,2.344 3.104,0.188 10 false ROCKER REINFORCE SUB-ASSEMBLY OUTER 3.198,2.573 6.198,2.75 3,0.177 10 false FRONT BODY PILLAR SUB-ASSEMBLY INNER 0.25,9.469 1.479,9.667 1.229,0.198 10 false mm (in.) 0.25,0.271 1.938,0.469 1.688,0.198 12 false for Type B:

K141767E02
5.344,7.26 5.938,7.458 0.594,0.198 10 false 10 (0.39) 4.115,9.083 4.708,9.281 0.594,0.198 10 false 15 (0.59) 5.469,9.063 6.063,9.26 0.594,0.198 10 false 15 (0.59) 0.25,9.469 1.479,9.667 1.229,0.198 10 false mm (in.)

K141768E02
1.115,8.833 1.406,8.833 1.406,8.833 1.927,8.313 false 2.292,5.958 2.792,5.146 2.792,5.146 3.313,5.146 false 0.948,8.729 1.26,8.927 0.313,0.198 10 false *4 3.375,5.063 5.344,5.229 1.969,0.167 10 false FRONT BODY PILLAR OUTER