Home › Vehicle Exterior › BODY PANEL › FIT STANDARD / ADJUSTMENT METHOD › from 2017.06
BM2170E _01 Vehicle Exterior _057059 BODY PANEL _0278261 FIT STANDARD / ADJUSTMENT METHOD F

BODY PANEL  FIT STANDARD / ADJUSTMENT METHOD  ADJUSTMENT  


INSPECT HOOD SUB-ASSEMBLY


a.

Check that the clearance measurements of areas "a" through "f" are within each standard range.

B477864N01
0.677,2.75 0.833,2.948 0.156,0.198 10 false a 2.729,0.958 2.885,1.156 0.156,0.198 10 false b 2.354,1.552 2.51,1.75 0.156,0.198 10 false c 4.938,0.719 5.094,0.917 0.156,0.198 10 false d 5.906,0.833 6.063,1.031 0.156,0.198 10 false e

Standard Clearance
Area Measurement Area Measurement
a 2.15 to 6.15 mm (0.0846 to 0.242 in.) b 2.35 to 6.35 mm (0.0925 to 0.250 in.)
c -2.15 to 1.85 mm (-0.0846 to 0.0728 in.) d 2.0 to 5.0 mm (0.0787 to 0.197 in.)
e -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) - -



ADJUST HOOD SUB-ASSEMBLY


B301499

a.

Horizontally and vertically adjust the hood.

i.

Loosen the 4 hinge bolts of the hood.


ii.

Adjust the clearance between the hood and front fender by moving the hood.


iii.

Tighten the 4 hinge bolts after the adjustment.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



b.
B477865

Adjust the height of the front end of the hood using the cushion rubbers.

i.

Adjust the 2 cushion rubbers so that the heights of the hood and fender are aligned.

HINT:

Raise or lower the front end of the hood by turning the 2 cushion rubbers.




c.
B477866

Adjust the hood lock.

i.

Loosen the 3 bolts.


ii.

Tighten the bolts after adjustment.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


iii.

Check that the striker can engage with the hood lock smoothly.




HINT:

Centering bolts are used to mount the hood hinge and hood lock. The hood and hood lock cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.


INSPECT FRONT DOOR


a.

Check that the clearance measurements of areas "a" through "i" are within each standard range.

B301507E03
0.949,2.432 1.141,2.579 0.192,0.148 10 a 2.246,1.08 2.439,1.228 0.192,0.148 10 b 2.447,0.431 2.639,0.579 0.192,0.148 10 c 3.82,1.06 4.012,1.208 0.192,0.148 10 d 4.026,0.443 4.218,0.590 0.192,0.148 10 e 5.986,1.725 6.179,1.873 0.192,0.148 10 f 2.306,4.939 2.498,5.087 0.192,0.148 10 g 3.868,5.076 4.060,5.224 0.192,0.148 10 h 6.057,4.828 6.249,4.976 0.192,0.148 10 i

Standard Clearance
Area Measurement Area Measurement
a 2.7 to 5.7 mm (0.106 to 0.224 in.) b 1.9 to 4.9 mm (0.0748 to 0.193 in.)
c 3.2 to 6.2 mm (0.126 to 0.244 in.) d 2.0 to 5.0 mm (0.0787 to 0.197 in.)
e 3.2 to 6.2 mm (0.126 to 0.244 in.) f 3.2 to 6.2 mm (0.126 to 0.244 in.)
g 4.2 to 7.2 mm (0.165 to 0.283 in.) h 4.2 to 7.2 mm (0.165 to 0.283 in.)
i 3.2 to 6.2 mm (0.126 to 0.244 in.) - -



HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.



ADJUST FRONT DOOR


B297607

NOTICE:

Make sure to turn the ignition switch off when adjusting door lock strikers.


a.

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the body side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Tighten the door side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


d.
B297608

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


e.

Using a brass bar and a hammer, hit the striker to adjust its position.


f.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT REAR DOOR


a.

Check that the clearance measurements of areas "a" through "m" are within each standard range.

B301508E01
1.074,2.375 1.268,2.561 0.194,0.186 10 a 1.635,2.126 1.829,2.312 0.194,0.186 10 b 2.232,0.595 2.426,0.781 0.194,0.186 10 c 2.254,1.37 2.448,1.556 0.194,0.186 10 d 3.783,0.581 3.978,0.767 0.194,0.186 10 e 3.798,1.371 3.992,1.557 0.194,0.186 10 f 6.001,2.143 6.195,2.329 0.194,0.186 10 g 6.396,1.91 6.590,2.096 0.194,0.186 10 h 6.503,3.898 6.697,4.084 0.194,0.186 10 i 6.084,4.612 6.278,4.798 0.194,0.186 10 j 3.912,4.945 4.106,5.131 0.194,0.186 10 k 3.026,5.281 3.220,5.467 0.194,0.186 10 l 2.242,5.03 2.436,5.216 0.194,0.186 10 m

Standard Clearance
Area Measurement Area Measurement
a 3.2 to 6.2 mm (0.126 to 0.244 in.) b -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
c 3.2 to 6.2 mm (0.126 to 0.244 in.) d 2.1 to 5.1 mm (0.0827 to 0.167 in.)
e 3.2 to 6.2 mm (0.126 to 0.244 in.) f 2.3 to 5.3 mm (0.0906 to 0.209 in.)
g 2.7 to 5.7 mm (0.106 to 0.224 in.) h -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
i -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) j 2.7 to 5.7 mm (0.106 to 0.224 in.)
k 4.2 to 7.2 mm (0.165 to 0.283 in.) l 3.2 to 6.2 mm (0.126 to 0.244 in.)
m -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) - -



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.



ADJUST REAR DOOR


B297646

NOTICE:

Make sure to turn the power switch off when adjusting door lock strikers.


a.

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the vehicle body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B297644

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT BACK DOOR


a.

Check that the clearance measurements of areas "a" through "g" are within each standard range.

B301509E02
0.623,2.047 0.831,2.252 0.208,0.205 10 a 1.101,2.419 1.309,2.624 0.208,0.205 10 b 1.993,2.003 2.200,2.208 0.208,0.205 10 c 2.429,2.361 2.637,2.566 0.208,0.205 10 d 5.701,2.272 5.909,2.476 0.208,0.205 10 e 6.274,4.042 6.482,4.247 0.208,0.205 10 f 4.272,5.402 4.480,5.607 0.208,0.205 10 g

Standard Clearance
Area Measurement Area Measurement
a 5.7 to 8.7 mm (0.244 to 0.343 in.) b -0.5 to 2.5 mm (-0.0197 to 0.0197 in.)
c 5.7 to 8.7 mm (0.244 to 0.343 in.) d -0.5 to 2.5 mm (-0.0197 to 0.0197 in.)
e
(Reference)
5.35 mm (0.211 in.) f 3.05 to 7.05 mm (0.12 to 0.278 in.)
g 4.15 to 8.15 mm (0.163 to 0.321 in.) - -



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.



ADJUST BACK DOOR


B300318

a.

Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.


b.

Tighten the body side hinge after adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
B300319

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


d.

Using a brass bar and a hammer, hit the striker to adjust its position.


e.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)