PRECAUTION
| *a | Colored identification mark on the bottom of the rear coil spring |
Standard values indicated by *1 and *2 in the specification tables are for the vehicles with a purple or blue identification mark on the bottom of the rear coil spring.
MEASURE VEHICLE HEIGHT
Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
Be sure to perform measurement on a level surface.
If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
Inspect while the vehicle is unloaded.
The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Measure the vehicle height.
A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center
B: Ground clearance of rear axle beam bushing set bolt center
C: Ground clearance of front wheel center
D: Ground clearance of rear wheel center
| Tire Size | Front C - A | Rear D - B |
|---|---|---|
|
*1: Vehicles with purple identification mark on the bottom of the rear coil spring *2: Vehicles with blue identification mark on the bottom of the rear coil spring *3: for New Zealand *4: for Korea |
||
| 175/65R15 | 92 mm (3.62 in.)
98 mm (3.86 in.)*4 |
29 mm (1.14 in.)
34 mm (1.34 in.)*4 |
| 185/60R15 | 93 mm (3.66 in.)
79 mm (3.11 in.)*1 69 mm (2.72 in.)*2 92 mm (3.62 in.)*3 |
32 mm (1.26 in.)
14 mm (0.551 in.)*1 4 mm (0.157 in.)*2 28 mm (1.10 in.)*3 |
INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION
Inspect while the vehicle is unloaded.
| *a | Turning Radius Gauge |
| *b | Camber-caster-kingpin Gauge |
Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.
Inspect the camber, caster and steering axis inclination.
| Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|
|
*1: Vehicles with purple identification mark on the bottom of the rear coil spring *2: Vehicles with blue identification mark on the bottom of the rear coil spring *3: for New Zealand *4: for Korea |
||
| 175/65R15 | -0°13' +/- 0°45' (-0.22° +/- 0.75°)
-0°16' +/- 0°45' (-0.27° +/- 0.75°)*4 |
0°30' (0.50°) or less |
| 185/60R15 | -0°13' +/- 0°45' (-0.22° +/- 0.75°)
-0°04' +/- 0°45' (-0.07° +/- 0.75°)*1 0°05' +/- 0°45' (0.08° +/- 0.75°)*2 -0°12' +/- 0°45' (-0.20° +/- 0.75°)*3 |
|
| Tire Size | Caster Inclination | Right-left Difference |
|---|---|---|
|
*1: Vehicles with purple identification mark on the bottom of the rear coil spring *2: Vehicles with blue identification mark on the bottom of the rear coil spring *3: for New Zealand *4: for Korea |
||
| 175/65R15 | 4°54' +/- 0°45' (4.90° +/- 0.75°)
4°57' +/- 0°45' (4.95° +/- 0.75°)*4 |
0°30' (0.50°) or less |
| 185/60R15 | 4°59' +/- 0°45' (4.98° +/- 0.75°)
4°41' +/- 0°45' (4.68° +/- 0.75°)*1 4°32' +/- 0°45' (4.53° +/- 0.75°)*2 4°53' +/- 0°45' (4.88° +/- 0.75°)*3 |
|
| Tire Size | Steering Axis Inclination Reference |
|---|---|
|
*1: Vehicles with purple identification mark on the bottom of the rear coil spring *2: Vehicles with blue identification mark on the bottom of the rear coil spring *3: for New Zealand *4: for Korea |
|
| 175/65R15 | 11°23' (11.38°)
11°31' (11.52°)*4 |
| 185/60R15 | 11°25' (11.42°)
11°04' (11.07°)*1 10°49' (10.82°)*2 11°23' (11.38°)*3 |
INSPECT TOE-IN (FRONT)
Inspect while the vehicle is unloaded.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to N.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)
| *a | Tread Center Mark |
| *b | Dimension B |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.
Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.
| *a | Dimension A |
|
Front of the Vehicle |
Measure the distance between the tread center marks on the front of the wheels (dimension A).
| Tire Size | Specified Condition |
|---|---|
| 175/65R15 | C + D: 0°06' +/- 0°12' (0.10° +/- 0.21°) |
| B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.) | |
| 185/60R15 | C + D: 0°06' +/- 0°12' (0.09° +/- 0.19°) |
| B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.) |
Measure "B - A" only when "C + D" cannot be measured.
If the toe-in is not within the specified range, adjust it at the rack ends.
INSPECT WHEEL ANGLE
| *a | Inside |
| *b | Outside |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of a turning radius gauge.
Turn the steering wheel fully to the left and right and measure the turning angle.
Inspect while the vehicle is unloaded.
| Tire Size | - | Inside Wheel | Outside Wheel Reference |
|---|---|---|---|
|
*1: Vehicles with purple identification mark on the bottom of the rear coil spring *2: Vehicles with blue identification mark on the bottom of the rear coil spring *3: for New Zealand *4: for Korea *5: for Taiwan |
|||
| 175/65R15 (5J) | - | 40°50' +/- 2° (40.83° +/- 2°)*5
40°42' +/- 2° (40.70° +/- 2°)*4 |
35°11' (35.18°)*5
35°02' (35.03°)*4 |
| 175/65R15 (5.5J) | - | 40°04' +/- 2° (40.07° +/- 2°)*3 | 34°41' (34.68°)*3 |
| 185/60R15 | for LHD | 40°50' +/- 2° (40.83° +/- 2°)
41°09' +/- 2° (41.15° +/- 2°)*1 41°21' +/- 2° (41.35° +/- 2°)*2 |
35°09' (35.15°)
35°30' (35.50°)*1 35°44' (35.73°)*2 |
| for RHD | 40°00' +/- 2° (40.00° +/- 2°)
40°21' +/- 2° (40.35° +/- 2°)*1 40°32' +/- 2° (40.53° +/- 2°)*2 40°52' +/- 2° (40.87° +/- 2°)*3 |
34°38' (34.63°)
35°06' (35.10°)*1 35°14' (35.23°)*2 35°11' (35.18°)*3 |
|
If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.
INSPECT CAMBER (REAR)
Inspect while the vehicle is unloaded.
Install a camber-caster-kingpin gauge.
Inspect the camber.
| Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|
|
*1: Vehicles with purple identification mark on the bottom of the rear coil spring *2: Vehicles with blue identification mark on the bottom of the rear coil spring *3: for New Zealand *4: for Korea |
||
| 175/65R15 | -0°57' +/- 0°30' (-0.95° +/- 0.50°)
-0°58' +/- 0°30' (-0.97° +/- 0.50°)*4 |
0°30' (0.50°) or less |
| 185/60R15 | -0°58' +/- 0°30' (-0.97° +/- 0.50°)
-0°55' +/- 0°30' (-0.92° +/- 0.50°)*1 -0°54' +/- 0°30' (-0.90° +/- 0.50°)*2 -0°57' +/- 0°30' (-0.95° +/- 0.50°)*3 |
|
Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.
INSPECT TOE-IN (REAR)
Inspect while the vehicle is unloaded.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to N.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
| *a | Tread Center Mark |
| *b | Dimension B |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.
Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step A again.
| *a | Dimension A |
|
Front of the Vehicle |
Measure the distance between the tread center marks on the front of the wheels (dimension A).
| Tire Size | Specified Condition | Right-left Difference |
|---|---|---|
|
*1: Vehicles with purple identification mark on the bottom of the rear coil spring *2: Vehicles with blue identification mark on the bottom of the rear coil spring *3: for New Zealand *4: for Korea |
||
| 175/65R15 | C + D: 0°20' +/- 0°15' ( 0.33° +/- 0.25°)
C + D: 0°21' +/- 0°15' ( 0.35° +/- 0.25°)*4 |
0°30' (0.50°) or less |
| B - A: 3.9 +/- 3.0 mm (0.154 +/- 0.118 in.)
B - A: 4.0 +/- 3.0 mm (0.157 +/- 0.118 in.)*4 |
6.0 mm (0.236 in.) or less | |
| 185/60R15 | C + D: 0°21' +/- 0°15' ( 0.35° +/- 0.25°)
C + D: 0°17' +/- 0°15' ( 0.28° +/- 0.25°)*1 C + D: 0°14' +/- 0°15' ( 0.23° +/- 0.25°)*2 C + D: 0°20' +/- 0°15' ( 0.33° +/- 0.25°)*3 |
0°30' (0.50°) or less |
| B - A: 3.9 +/- 3.0 mm (0.154 +/- 0.118 in.)
B - A: 3.2 +/- 3.0 mm (0.126 +/- 0.118 in.)*1 B - A: 2.8 +/- 3.0 mm (0.110 +/- 0.118 in.)*2 B - A: 3.8 +/- 3.0 mm (0.150 +/- 0.118 in.)*3 |
6.0 mm (0.236 in.) or less | |
Measure "B - A" only when "C + D" cannot be measured.
If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.