Heat the double-sided tape remaining on the body with an infrared lamp or equivalent.
Heat the tape to 40 to 60°C for approximately 1 to 2 minutes.
Wipe off the remaining double-sided tape using a clean cloth or equivalent.
If a name plate is installed without thoroughly removing the remaining double-sided tape from the body, the name plate will not adhere properly. Make sure to thoroughly wipe off the double-sided tape.
After cleaning the installation area of the body with degreasing agent, attach the name plate to the position shown in the illustration.
The working environment should be 20°C when installing the name plate. If the working environment is below 20°C, heat the installation area of the body to 20 to 30°C and then install the name plate.
| *A | for Type A | *B | for LH Side |
| *C | for RH Side | - | - |
| *1 | LUGGAGE COMPARTMENT DOOR EMBLEM | *2 | NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE |
| *3 | NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE | - | - |
| ● | Non-reusable part | - | - |
| *A | for Type B | *B | for RH Side |
| *1 | LUGGAGE COMPARTMENT DOOR EMBLEM | *2 | NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE |
| *3 | NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE | - | - |
| ● | Non-reusable part | - | - |
| *A | for LH Side | *B | for RH Side |
| *1 | SIDE PANEL EMBLEM | - | - |
| ● | Non-reusable part | - | - |
INSTALL SIDE PANEL EMBLEM (for RH Side)
Install the side panel emblem as shown in the illustration.
| *a | Location Pin | - | - |
INSTALL SIDE PANEL EMBLEM (for LH Side)
Install the side panel emblem as shown in the illustration.
| *a | Location Pin | - | - |
INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE (for Type B)
Install the No. 2 luggage compartment door name plate as shown in the illustration.
| *a | Profile of Back Door Panel | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 150.1 mm (5.91 in.) | B | 165.9 mm (6.53 in.) |
| C | 150.0 mm (5.91 in.) | - | - |
INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE (for Type A)
Install the No. 2 luggage compartment door name plate as shown in the illustration.
| *a | Profile of Back Door Panel | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 151.1 mm (5.95 in.) | B | 219.3 mm (8.63 in.) |
| C | 149.5 mm (5.89 in.) | - | - |
INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE (for RH Side)
Install the No. 1 luggage compartment door name plate as shown in the illustration.
| *A | for Type A | *B | for Type B |
| *a | Profile of Back Door Panel | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 329.8 mm (1.08 ft.) | B | 146.6 mm (5.77 in.) |
| C | 329.5 mm (1.08 ft.) | D | 159.2 mm (6.27 in.) |
| E | 125.5 mm (4.94 in.) | F | 159.0 mm (6.26 in.) |
INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE (for LH Side)
Install the No. 1 luggage compartment door name plate as shown in the illustration.
| *a | Profile of Back Door Panel | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 149.9 mm (5.90 in.) | B | 167.1 mm (6.58 in.) |
| B | 150.3 mm (5.92 in.) | - | - |
INSTALL LUGGAGE COMPARTMENT DOOR EMBLEM
| *a | Location Pin |
Install the luggage compartment door emblem as shown in the illustration.