Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS › from 2018.08
BM2170E _V1 General _057058 INTRODUCTION _0278232 WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


PRECAUTION


C253259C01
2.094,1.698 2.875,1.698 true 2.917,1.604 3.083,1.781 0.167,0.177 10 false *a
*a Colored identification mark on the bottom of the rear coil spring


Standard values indicated by *1 and *2 in the specification tables are for the vehicles with a purple or blue identification mark on the bottom of the rear coil spring.


MEASURE VEHICLE HEIGHT


NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C249970N03
0.19,3.754 0.320,3.896 0.130,0.142 10 C 1.459,3.825 1.583,3.967 0.124,0.142 10 A 1.825,3.788 1.943,3.930 0.118,0.142 10 B 3.219,3.757 3.341,3.899 0.122,0.142 10 D

Measure the vehicle height.

Measurement points:

A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center


B: Ground clearance of rear axle beam bushing set bolt center


C: Ground clearance of front wheel center


D: Ground clearance of rear wheel center


Vehicle Height (Unloaded Vehicle):
Tire Size Front C - A Rear D - B

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 92 mm (3.62 in.)*1, *3
76 mm (2.99 in.)*2, *3
98 mm (3.86 in.)*4
29 mm (1.14 in.)*1, *3
12 mm (0.472 in.)*2, *3
34 mm (1.34 in.)*4
185/60R15 93 mm (3.66 in.)
79 mm (3.11 in.)*1
69 mm (2.72 in.)*2
77 mm (3.03 in.)*1, *5
92 mm (3.62 in.)*6
32 mm (1.26 in.)
14 mm (0.551 in.)*1
4 mm (0.157 in.)*2
12 mm (0.472 in.)*1, *5
28 mm (1.10 in.)*6




INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C25
2.396,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.458 false 2.76,0.729 2.99,0.906 0.229,0.177 10 false *b 0.448,0.604 0.688,0.781 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
Tire Size Camber Inclination Right-left Difference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°)*1, *3
0°00' +/- 0°45' (0.00° +/- 0.75°)*2, *3
-0°16' +/- 0°45' (-0.27° +/- 0.75°)*4
0°30' (0.50°) or less
185/60R15 -0°13' +/- 0°45' (-0.22° +/- 0.75°)
-0°04' +/- 0°45' (-0.07° +/- 0.75°)*1
0°05' +/- 0°45' (0.08° +/- 0.75°)*2
-0°02' +/- 0°45' (-0.03° +/- 0.75°)*1, *5
-0°12' +/- 0°45' (-0.20° +/- 0.75°)*6


Caster (Unloaded Vehicle):
Tire Size Caster Inclination Right-left Difference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 4°54' +/- 0°45' (4.90° +/- 0.75°)*1, *3
4°38' +/- 0°45' (4.63° +/- 0.75°)*2, *3
4°57' +/- 0°45' (4.95° +/- 0.75°)*4
0°30' (0.50°) or less
185/60R15 4°59' +/- 0°45' (4.98° +/- 0.75°)
4°41' +/- 0°45' (4.68° +/- 0.75°)*1
4°32' +/- 0°45' (4.53° +/- 0.75°)*2
4°38' +/- 0°45' (4.63° +/- 0.75°)*1, *5
4°53' +/- 0°45' (4.88° +/- 0.75°)*6


Steering Axis (Unloaded Vehicle):
Tire Size Steering Axis Inclination Reference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 11°23' (11.38°)*1, *3
11°01' (11.02°)*2, *3
11°31' (11.52°)*4
185/60R15 11°25' (11.42°)
11°04' (11.07°)*1
10°49' (10.82°)*2
11°02' (11.03°)*1, *5
11°23' (11.38°)*6




INSPECT TOE-IN (FRONT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968C24
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 *a 2.427,1.698 2.604,1.854 0.177,0.156 10 *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



f.
C188969C24
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
Tire Size Specified Condition
175/65R15 C + D: 0°06' +/- 0°12' (0.10° +/- 0.21°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)
185/60R15 C + D: 0°06' +/- 0°12' (0.09° +/- 0.19°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rack ends.



INSPECT WHEEL ANGLE


C132439C20
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


a.

Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle):
Tire Size Inside Wheel Outside Wheel Reference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 40°50' +/- 2° (40.83° +/- 2°)*1, *3
41°12' +/- 2° (41.20° +/- 2°)*2, *3
40°42' +/- 2° (40.70° +/- 2°)*4
35°11' (35.18°)*1, *3
35°32' (35.53°)*2, *3
35°02' (35.03°)*4
185/60R15 40°50' +/- 2° (40.83° +/- 2°)
41°09' +/- 2° (41.15° +/- 2°)*1
41°21' +/- 2° (41.35° +/- 2°)*2
41°11' +/- 2° (41.18° +/- 2°)*1, *5
40°52' +/- 2° (40.87° +/- 2°)*6
35°09' (35.15°)
35°30' (35.50°)*1
35°44' (35.73°)*2
35°32' (35.53°)*1, *5
35°11' (35.18°)*6


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.




INSPECT CAMBER (REAR)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle):
Tire Size Camber Inclination Right-left Difference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 -0°57' +/- 0°30' (-0.95° +/- 0.50°)*1, *3
-0°55' +/- 0°30' (-0.92° +/- 0.50°)*2, *3
-0°58' +/- 0°30' (-0.97° +/- 0.50°)*4
0°30' (0.50°) or less
185/60R15 -0°58' +/- 0°30' (-0.97° +/- 0.50°)
-0°55' +/- 0°30' (-0.92° +/- 0.50°)*1
-0°54' +/- 0°30' (-0.90° +/- 0.50°)*2
-0°55' +/- 0°30' (-0.92° +/- 0.50°)*1, *5
-0°57' +/- 0°30' (-0.95° +/- 0.50°)*6


HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.




INSPECT TOE-IN (REAR)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968C25
0.83,0.579 0.83,1.114 false 1.361,0.579 1.361,0.992 1.361,0.992 0.83,0.992 false 0.739,1.134 0.912,1.302 0.173,0.168 10 *a 2.432,1.697 2.607,1.858 0.176,0.161 10 *b 2.522,1.33 2.522,1.671 false
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step A again.



f.
C188969C25
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
Tire Size Specified Condition Right-left Difference

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

*3: for Taiwan

*4: for Korea

*5: for Australia

*6: for New Zealand

175/65R15 C + D: 0°20' +/- 0°15' ( 0.33° +/- 0.25°)*1, *3
C + D: 0°16' +/- 0°15' ( 0.27° +/- 0.25°)*2, *3
C + D: 0°21' +/- 0°15' ( 0.35° +/- 0.25°)*4
0°30' (0.50°) or less
B - A: 3.9 +/- 3.0 mm (0.154 +/- 0.118 in.)*1, *3
B - A: 3.2 +/- 3.0 mm (0.126 +/- 0.118 in.)*2, *3
B - A: 4.0 +/- 3.0 mm (0.157 +/- 0.118 in.)*4
6.0 mm (0.236 in.) or less
185/60R15 C + D: 0°21' +/- 0°15' ( 0.35° +/- 0.25°)
C + D: 0°17' +/- 0°15' ( 0.28° +/- 0.25°)*1
C + D: 0°14' +/- 0°15' ( 0.23° +/- 0.25°)*2
C + D: 0°16' +/- 0°15' ( 0.27° +/- 0.25°)*1, *5
C + D: 0°20' +/- 0°15' ( 0.33° +/- 0.25°)*6
0°30' (0.50°) or less
B - A: 3.9 +/- 3.0 mm (0.154 +/- 0.118 in.)
B - A: 3.2 +/- 3.0 mm (0.126 +/- 0.118 in.)*1
B - A: 2.8 +/- 3.0 mm (0.110 +/- 0.118 in.)*2
B - A: 3.1 +/- 3.0 mm (0.122 +/- 0.118 in.)*1, *5
B - A: 3.8 +/- 3.0 mm (0.150 +/- 0.118 in.)*6
6.0 mm (0.236 in.) or less


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.