Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2014.12–2017.06
NM2170E _51 Engine / Hybrid System _056959 HYBRID / BATTERY CONTROL _0277754 HYBRID CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  GENERAL  


OUTLINE


a.

The hybrid system of this hybrid vehicle employs the Toyota Hybrid System-II (THS-II) under the "Hybrid Synergy Drive" concept*.


b.

Hybrid vehicles use a combination of 2 kinds of power sources, such as an engine and HV battery, so as to take advantage of the benefits provided by each power source while compensating for each other's shortcomings. As a result, efficient operation is achieved.


c.

Hybrid vehicles do not need their batteries to be charged externally unlike existing electric-only vehicles. Therefore, special infrastructure is not required to use hybrid vehicles.


d.

Technical development of power units (such as an engine or fuel cell) is advancing in various fields. The hybrid system is a flexible system that uses a high-efficiency power unit and electric motors.


e.

Hybrid vehicles have high-voltage electrical circuits. Hybrid vehicles have been developed with consideration given to the protection of drivers and technicians against electrocution.

HINT:

*: The "Hybrid Synergy Drive" concept consists of 4 key benefits: Fuel efficiency, low emissions, seamless acceleration and silent performance.




SPECIFICATION


a.

Motor Generator

Item Specification
Motor Generator No. 1 (MG1) Motor Generator No. 2 (MG2)
Type Permanent Magnet Motor Permanent Magnet Motor
Function Generate, Engine Starter Generate, Drive Wheels
Maximum System Voltage V DC 520 DC 520
Maximum Output kW - 45
Maximum Torque N*m - 169
Cooling System Air-cooled Air-cooled


b.

Inverter with Converter Assembly

Item Specification
Boost Converter Rated Voltage (Inverter Side) V DC 520
Rated Voltage (HV Battery Side) V DC 144
DC-DC Converter Rated Output Voltage V DC 13.5 to 15.0 (normal condition), DC 11.5 (When the engine coolant temperature is approximately -10°C (14°F) or lower)
Maximum Output Current A 80 (normal condition), 85 (When the hybrid system temperature is approximately 15°C (59°F) or lower.)


c.

HV Battery

Item Specification
Type Nickel Metal Hydride (Ni-MH) Battery
Cell Quantity 120 Cells (6 Cells x 20 Modules)
Nominal Voltage V 144
Battery Capacity (3HR) Ah 6.5


d.

Cooling System (for Inverter with Converter Assembly)

Item Specification
Inverter Water Pump Assembly (with Motor) Motor Type Brushless
Discharge Volume Liter (US qts, Imp. qts) 10 (10.6, 8.8) /min. or greater
Coolant Type Toyota Genuine Super Long Life Coolant (SLLC)
Color Pink
Capacity Liter (US qts, Imp. qts) 1.6 (1.7, 1.4)
Maintenance Intervals First Time km (miles) 240000 (150000)
Subsequent km (miles) Every 80000 (50000)


e.

Cooling System (for HV Battery)

Item Specification
Battery Cooling Blower Assembly Motor Type Brushless
Fan Type Sirocco Fan
Air Flow Volume m3/h 160



MAIN FEATURES


a.

The THS-II control has the following features.

Item Outline
Idle Stop Idling of the engine is automatically stopped (idle stop) to reduce energy loss.
EV Drive
(Efficient Drive Control)
This allows the vehicle to be driven using only the electric motor when engine efficiency is low. In addition, electricity is generated when engine efficiency is high. Control is performed to maximize the total efficiency of the vehicle.
EV Drive Mode If the driver operates the switch and the operating conditions are being met, the vehicle can run on only the electric motor.
Motor Assist The electric motor supplements the engine power when accelerating.
Regenerative Braking
(Energy Regeneration)
During deceleration and while depressing the brake pedal, part of the energy that was lost as heat is collected as electrical energy to be reused, such as for motor power.


b.

The mechanism of the THS-II is as follows.

i.

The THS-II consists of mainly the engine, hybrid vehicle transaxle assembly, inverter with converter assembly and HV battery, and employs the series/parallel-type hybrid system.

W101195E11
2.479,1.156 2.76,1.354 0.281,0.198 10 false *1 1.521,1.719 1.802,1.917 0.281,0.198 10 false *2 3.271,1.823 3.552,2.021 0.281,0.198 10 false *3 2.479,2.469 2.76,2.667 0.281,0.198 10 false *4 2.458,1.74 2.74,1.938 0.281,0.198 10 false *5 2.458,1.938 2.74,2.135 0.281,0.198 10 false *6 3.458,2.479 3.74,2.677 0.281,0.198 10 false *7 4.521,2.458 4.802,2.656 0.281,0.198 10 false *8

Text in Illustration
*1 Engine *2 Hybrid Vehicle Transaxle Assembly
*3 Motor Generator No. 1 (MG1) *4 Motor Generator No. 2 (MG2)
*5 Power Split Planetary Gear Unit (Compound Gear Unit) *6 Motor Speed Reduction Planetary Gear Unit (Compound Gear Unit)
*7 Inverter with Converter Assembly *8 HV Battery
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -

HINT:

Generally, there are 3 types of hybrid systems: A series-type hybrid system, a parallel-type hybrid system and a series/parallel-type hybrid system.


·

In a series-type hybrid system, the motor rotates the wheels and the engine, using a generator, acts as an electric power source for the motor.

W101596E10
1.042,1.292 1.313,1.49 0.271,0.198 10 false *1 2,1.292 2.271,1.49 0.271,0.198 10 false *2 3.604,1.292 3.875,1.49 0.271,0.198 10 false *4 3.604,0.802 3.875,1 0.271,0.198 10 false *3 5.167,1.292 5.438,1.49 0.271,0.198 10 false *5

Text in Illustration
*1 Engine *2 Generator
*3 Inverter *4 HV Battery
*5 Motor - -
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -

·

In a parallel-type hybrid system, both the engine and the motor generator directly rotate the wheels. In addition to supplementing the power of the engine, the motor generator can also serve as a generator to charge the HV battery while the vehicle is in motion. Driving the vehicle only with the motor generator is also possible.

W101597E09
3.073,0.76 3.344,0.958 0.271,0.198 10 false *1 3.771,0.76 4.042,0.958 0.271,0.198 10 false *2 1.146,1.833 1.417,2.031 0.271,0.198 10 false *3 2.333,1.833 2.604,2.031 0.271,0.198 10 false *4 3.823,1.844 4.094,2.042 0.271,0.198 10 false *5

Text in Illustration
*1 Engine *2 Transmission
*3 HV Battery *4 Inverter
*5 Motor Generator - -
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -

·

In a series/parallel-type hybrid system, aspects of both a series-type hybrid system and a parallel-type hybrid system are combined. The system has 2 motor generators. Electricity can be generated by motor generator No. 1 using engine power. The generated electricity is used to charge the HV battery and also to power motor generator No. 2.

W101598E11
4.917,0.635 5.188,0.833 0.271,0.198 10 false *1 1.115,1.615 1.385,1.813 0.271,0.198 10 false *3 2.333,1.604 2.604,1.802 0.271,0.198 10 false *4 4.917,1.979 5.188,2.177 0.271,0.198 10 false *6 3.792,1.208 4.063,1.406 0.271,0.198 10 false *5 4.917,1.219 5.188,1.417 0.271,0.198 10 false *2

Text in Illustration
*1 Engine *2 Power Split Planetary Gear Unit
*3 HV Battery *4 Inverter
*5 Motor Generator No. 1 *6 Motor Generator No. 2
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -



ii.

This system optimally performs cooperative control of the 1NZ-FXE engine, and Motor Generator No. 1 (MG1) and Motor Generator No. 2 (MG2) in the P510 hybrid vehicle transaxle assembly that provides excellent transmission performance.


iii.

The system has 2 batteries that are used in different purposes. One is the HV battery (nominal voltage of DC 144 V) that stores electrical power to drive the vehicle, and the other is the auxiliary battery (nominal voltage of DC 12 V) that supplies electrical power to the electrical components.


iv.

Furthermore, it uses a variable-voltage system consisting of a high-output HV battery with a nominal voltage of DC 144 V, a boost converter that boosts the operating voltage of MG1 and MG2 to a maximum voltage of DC 520 V, and an inverter that converts direct current and alternating current.


v.

Since hybrid vehicles are not equipped with a conventional alternator, the high-voltage from the HV battery is dropped to approximately DC 14 V using a DC-DC converter in order to charge the auxiliary battery. Also, the HV battery regularly charges and discharges within the constant State of Charge (SOC) range while the vehicle is running, thus, recharging from external power sources is not necessary.

W125151E03
0.792,0.406 0.896,0.406 0.896,0.406 1.719,2.479 true 3.26,0.438 3.156,0.438 3.156,0.438 2.052,2.719 true 4.927,0.229 4.823,0.229 4.823,0.229 3.906,2.125 true 1.188,4.406 1.292,4.406 1.292,4.406 1.927,3.104 true 5.156,3.958 5.063,3.958 5.063,3.958 4.427,2.656 true 4.958,0.146 5.167,0.323 0.208,0.177 10 false *3 3.292,0.354 3.521,0.542 0.229,0.188 10 false *2 0.625,0.323 0.813,0.49 0.188,0.167 10 false *1 1.021,4.323 1.229,4.521 0.208,0.198 10 false *4 5.177,3.875 5.406,4.063 0.229,0.188 10 false *5

Text in Illustration
*1 1NZ-FXE Engine *2

Inverter with Converter Assembly

-

Inverter

-

Boost Converter

-

DC-DC Converter



*3 Auxiliary Battery *4

P510 Hybrid Vehicle Transaxle Assembly

-

Motor Generator No. 1 (MG1)

-

Motor Generator No. 2 (MG2)



*5 HV Battery Assembly - -


vi.

A cooling system that is independent from the engine cooling system is provided to cool the inverter with converter assembly.


vii.

The radiator for the hybrid system is integrated with the radiator assembly for the engine. This makes the cooling system more compact and lightweight.

W105737E04
4.656,1.156 5.385,0.552 5.385,0.552 5.542,0.552 true 1.469,4.271 1.635,4.271 1.635,4.271 2.604,3.375 true 4.094,2.906 5.417,4.219 5.417,4.219 5.552,4.219 true 5.573,0.458 5.833,0.635 0.26,0.177 10 false *1 5.583,4.125 5.823,4.323 0.24,0.198 10 false *3 1.292,4.188 1.521,4.365 0.229,0.177 10 false *2

Text in Illustration
*1 Inverter Reserve Tank Assembly *2 Radiator Assembly
*3 Inverter Water Pump Assembly (with Motor) - -
V100135

HV Coolant Flow - -


viii.

To ensure the proper performance of the HV battery while it generates heat during the repetitive charge and discharge cycles, a dedicated cooling system is used for the HV battery.


ix.

The cooling air inlet port has been designed below the rear seat to prevent the cooling air temperature from rising and improve cooling efficiency.

W106019E02
2.125,2.542 1.156,0.469 1.156,0.469 0.698,0.469 true 3.75,2.188 2.906,0.385 2.906,0.385 2.583,0.385 true 1.01,3.375 1.5,4.417 1.5,4.417 1.667,4.417 true 1.469,3.229 2.01,4.406 2.01,4.406 2.188,4.406 true 1.688,4.323 1.906,4.51 0.219,0.188 10 false *3 0.51,0.385 0.698,0.573 0.188,0.188 10 false *1 2.406,0.292 2.604,0.479 0.198,0.188 10 false *2 2.229,4.313 2.448,4.51 0.219,0.198 10 false *4

Text in Illustration
*1 HV Battery Assembly *2 Exhaust Air Duct (No. 1 Hybrid Battery Exhaust Duct)
*3 Battery Cooling Blower Assembly *4 Intake Air Duct (No. 1 Hybrid Battery Cover Intake Duct)
V100135

Cooling Air Flow - -




PRECAUTION


a.

Hybrid Vehicle High-voltage Safety Measures

i.

High-voltage safety is comprised of 2 points: "Insulation of High-voltage Circuits" and "Cut-off of High-voltage Circuits". The hybrid system also detects whether or not a decrease in insulation resistance has occurred between the high-voltage system and body ground.



b.

Insulation of High-voltage Circuits

i.

High-voltage circuits are used between the HV battery, inverter with converter assembly, hybrid vehicle transaxle assembly and compressor with motor assembly. Each of these items is connected by the power cables (frame wire) and is electrically insulated using cases and covers.


ii.

Cables (frame wire) are also shielded using a mesh conductor built into the electrical insulation of the wires. The shielding is grounded to the chassis of the vehicle and the main purpose is to prevent electromagnetic interference.

W105739E03
1.094,1.844 1.792,0.24 1.792,0.24 1.969,0.24 true 1.521,2.604 2.708,0.25 2.708,0.25 2.896,0.25 true 4.792,2.333 5.677,0.25 5.677,0.25 5.833,0.25 true 1.208,3.156 1.802,4.479 1.802,4.479 1.948,4.479 true 3.458,2.99 4.115,4.469 4.115,4.469 4.271,4.469 true 1.99,0.156 2.156,0.333 0.167,0.177 10 false *1 2.927,0.156 3.094,0.323 0.167,0.167 10 false *2 5.854,0.167 6.021,0.333 0.167,0.167 10 false *3 4.292,4.375 4.51,4.573 0.219,0.198 10 false *5 1.979,4.396 2.219,4.594 0.24,0.198 10 false *4

Text in Illustration
*1 Compressor with Motor Assembly *2 Hybrid Vehicle Transaxle Assembly
*3 HV Battery Assembly *4 Inverter with Converter Assembly
*5 Power Cable (Frame Wire) - -



c.

Cut-off of High-voltage Circuits

i.

When any of the conditions below occurs, the System Main Relays (SMRs) are automatically shut off by the hybrid vehicle control ECU.

·

Power switch is off.

·

Any airbag is deployed.

·

Inverter terminal cover is removed (interlock circuit is opened).

·

Power cable connector is disconnected (interlock circuit is opened).

·

Service plug grip handle is being unlocked (interlock circuit is opened).

·

A specified malfunction occurs.


W125152E02
2.427,1.896 3.292,2.115 0.865,0.219 10 false CAN (V Bus) 0.656,2.25 2.302,2.469 1.646,0.219 10 false Airbag Sensor Assembly 3.052,4.813 3.813,5.031 0.76,0.219 10 false HV Battery 2.302,5.417 2.927,5.854 0.625,0.438 10 false Service Plug Grip 4.135,1.354 5.948,1.583 1.813,0.229 10 false Hybrid Vehicle Control ECU 6.229,3.271 7.083,3.833 0.854,0.563 10 false To Power Cable (Frame Wire) 5.094,3.781 5.635,4 0.542,0.219 10 false SMRB 5.094,4.865 5.635,5.083 0.542,0.219 10 false SMRP 5.094,6.042 5.635,6.26 0.542,0.219 10 false SMRG 0.198,3.229 1.958,3.625 1.76,0.396 10 false Interlock Switch (For Inverter Terminal Cover) 0.188,4.719 1.958,5.125 1.771,0.406 10 false Interlock Switch (For Service Plug Grip) 0.188,3.979 1.906,4.385 1.719,0.406 10 false Interlock Switch (For Power Cable Connector) 6.229,5.521 7.083,6.135 0.854,0.615 10 false To Power Cable (Frame Wire) 0.844,0.427 1.76,0.625 0.917,0.198 10 false Power Switch 0.448,1.135 2.281,1.51 1.833,0.375 10 false Certification ECU (Smart Key ECU Assembly)


ii.

By removing the service plug grip before performing any inspection or service, the high-voltage circuit is shut off at the intermediate position of the HV battery, thus ensuring safety during service.

W106020E02
5.875,0.469 5.688,0.469 5.688,0.469 5.219,1.688 true 6.823,0.479 6.646,0.479 6.646,0.479 6.146,2.354 true 5.896,0.375 6.177,0.615 0.281,0.24 10 false *1 6.844,0.385 7.125,0.625 0.281,0.24 10 false *2

Text in Illustration
*1 Service Plug Grip *2 Insulated Gloves

CAUTION:

A charge remains in the high-voltage capacitor in the inverter with converter assembly after the high-voltage circuits are shut down. When servicing a hybrid vehicle, after the service plug grip is removed, wait at least 10 minutes to allow the capacitor to discharge before beginning work.


NOTICE:
·

The service plug grip should never be removed when the system is in the READY-on state.

·

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) unless instructed by the Repair Manual.





d.

HV Battery Handling Precautions

i.

HV battery electrolyte is a highly alkaline potassium hydroxide solution (odorless, transparent and colorless). Careless handling of the HV battery is very dangerous. Handle the HV battery properly according to the procedure below.

Item Procedure
When there is liquid leakage present in the area of the HV battery
·

Neutralize it with a saturated mixture of boric acid and water.

·

After litmus paper has been used to determine that the mixture is neutral, wipe it up with rags or waste cloth.


When battery electrolyte gets on skin, eyes etc.*
·

Flush it with a diluted solution of boric acid and water, or with a large amount of water.

·

Remove contaminated clothes at once.


When a vehicle is scrapped Remove the HV battery from the vehicle for collection via the specified route.
When the HV battery is stored The HV battery should not be left in a damp or humid location.
Prevention of the HV battery discharge or damage when a vehicle is stored for a long time
·

Disconnect the auxiliary battery negative terminal.

·

When in storage, the HV battery should be charged every 2 months. Using the following procedure, charge the HV battery with the vehicle.

(a)

Connect the negative terminal of the auxiliary battery.

(b)

Turn the power switch on (IG) for 3 minutes, do not apply any electrical loads (this operation is needed to allow the hybrid vehicle control ECU to detect the correct SOC).

(c)

Enter the READY-on state. After the engine starts, leave it running for 30 minutes to charge the HV battery. If the engine does not start or intermittently stops within 30 minutes, stop the operation at that time (the HV battery does not need to be charged).




CAUTION:

*: If you get electrolyte in your eyes, shout loudly for help, do not rub your eyes, rinse your eyes with large amount of water and seek medical attention immediately.