Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › ENGINE UNIT › 2011.12–2013.12
NM2170E _51 Engine / Hybrid System _056960 1NZ-FXE ENGINE MECHANICAL _0277755 ENGINE UNIT UN GENERAL/CONTROL/DETAILS F

1NZ-FXE ENGINE MECHANICAL  ENGINE UNIT  GENERAL/CONTROL/DETAILS  GENERAL  


OUTLINE


a.

The 1NZ-FXE engine is an in-line, 4-cylinder, 1.5-liter, 16-valve DOHC engine.


b.

This engine uses a high-expansion ratio Atkinson cycle, Variable Valve Timing-intelligent (VVT-i) system, Direct Ignition System (DIS), Electronic Throttle Control System-intelligent (ETCS-i) and Exhaust Gas Recirculation (EGR) system employing a highly efficient EGR cooler. In addition, use of an electric water pump has enhanced warm-up performance and reduced cooling losses. Thus, improved engine performance, quietness, fuel economy and cleaner emissions have been achieved.

W105926



SPECIFICATION


Engine Type 1NZ-FXE
No. of Cyls. and Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain Drive (with VVT-i)
Combustion Chamber Pentroof Type
Flow of Intake and Exhaust Gasses Cross-flow
Fuel System SFI
Ignition System DIS
Displacement 1497 cm3 (91.3 cu. in.)
Bore x Stroke 75.0 mm x 84.7 mm (2.95 in. x 3.33 in.)
Compression Ratio 13.4:1
Max. Output (SAE-NET)*1 54 kW@4800 rpm
Max. Torque (SAE-NET)*1 111 N*m@3600 - 4400 rpm
Valve Timing Intake Open 25°BTDC to 22°ATDC
Close 55°ABDC to 102°ABDC
Exhaust Open 34° BBDC
Close 2° ATDC
Oil Grade API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC
Firing Order 1 - 3 - 4 - 2
Research Octane Number (RON) 91 or higher
Emission Regulation EURO 5
Engine Service Mass*2 (Reference) 81.9 kg (181 lb)

*1: Maximum output and torque rating is determined by revised SAE J1349 standard.

*2: The figure shown is the weight of the engine without coolant and oil.


W105996E02
0.167,0.167 1.417,0.5 1.25,0.333 10 false Performance Curve: 0.594,1.417 1.469,1.708 0.875,0.292 10 false Torque (N*m) 1.49,0.844 1.948,1.042 0.458,0.198 10 false 120 1.49,1.427 1.948,1.625 0.458,0.198 10 false 100 1.563,2.021 1.875,2.219 0.313,0.198 10 false 80 2.219,4.25 2.833,4.448 0.615,0.198 10 false 1000 2.75,4.25 3.365,4.448 0.615,0.198 10 false 2000 3.271,4.25 3.885,4.448 0.615,0.198 10 false 3000 3.802,4.25 4.417,4.448 0.615,0.198 10 false 4000 4.302,4.25 4.917,4.448 0.615,0.198 10 false 5000 2.917,4.5 5.667,4.698 2.75,0.198 10 false Engine Speed (rpm) 5.25,0.833 5.563,1.031 0.313,0.198 10 false 60 5.25,1.333 5.563,1.531 0.313,0.198 10 false 50 5.25,1.885 5.563,2.083 0.313,0.198 10 false 40 5.25,2.417 5.563,2.615 0.313,0.198 10 false 30 5.25,2.969 5.563,3.167 0.313,0.198 10 false 20 5.25,3.5 5.563,3.698 0.313,0.198 10 false 10 5.25,4 5.406,4.198 0.156,0.198 10 false 0 5.552,2.417 6.417,2.698 0.865,0.281 10 false Output (kW)


MAIN FEATURES


a.

The 1NZ-FXE engine has achieved the following performance through the use of the items listed in the table below.

i.

High performance and reliability


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emissions and fuel economy

Item (1) (2) (3) (4) (5)
The high-expansion ratio Atkinson cycle is adopted. ○
Engine Control System The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ ○
The non-contact sensor is used in the throttle position sensor. ○
A flat type knock control sensor is used. ○
Engine Proper An aluminum cylinder block sub-assembly is used. ○
An offset crankshaft is used. ○ ○ ○
The taper squish shape is used for the top of the pistons. ○ ○
The skirt portion of the piston has a resin coating applied to reduce friction. ○ ○
Low-tension piston rings are used. ○ ○
Valve Mechanism A chain sub-assembly and No. 1 chain tensioner assembly are used. ○ ○
The Variable Valve Timing-intelligent (VVT-i) system is used. ○ ○
Fuel System 12-hole type fuel injector assemblies are used. ○ ○
A fuel delivery pipe made of pressed steel is used. ○ ○
A fuel returnless system is used. ○ ○
Quick connectors are used to connect the fuel hoses and fuel pipes. ○
Intake and Exhaust System A plastic intake manifold is used. ○
A linkless type throttle with motor body assembly is used. ○ ○
A step motor type Exhaust Gas Recirculation (EGR) valve assembly is used. ○
A water-cooled type EGR cooler assembly is used. ○ ○
A stainless steel exhaust manifold is used. ○
A rearward exhaust layout is used. ○
Three-Way Catalytic converters (TWCs) are used. ○
A 2-way exhaust control system is used. ○ ○
Cooling System An electric engine water pump assembly is used. ○ ○ ○ ○
Ignition System A Direct Ignition System (DIS) is used. ○ ○ ○