Home › Engine / Hybrid System › 1NZ-FXE (EMISSION CONTROL) › EMISSION CONTROL SYSTEM › 2014.12–2017.06
NM2170E _51 Engine / Hybrid System _056962 1NZ-FXE EMISSION CONTROL _0277757 EMISSION CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

1NZ-FXE EMISSION CONTROL  EMISSION CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the 1NZ-FXE emission control system are as follows.

Component Function
TWC Oxidizes CO and HC in the exhaust gas and deoxidizes NOx at the same time, to purify them into CO2, H2O and N2.
Oxygen Sensor This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
Air Fuel Ratio Sensor As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust gas. However, it detects the oxygen concentration in the exhaust gas linearly.
E.F.I. Vacuum Sensor Assembly Uses built-in semiconductors to detect the intake manifold pressure.
EGR Valve Assembly Operates when receiving signals from the ECM, regulating the EGR volume.
EGR Cooler Assembly Cools the exhaust gas temperature to improve the EGR efficiency.
Ventilation Valve Sub-assembly Opens and closes using vacuum generated in the intake manifold and controls the flow rate of the blowby gas.
Charcoal Canister Contains activated charcoal to absorb the fuel vapors that are created in the fuel tank assembly.
Purge VSV Opens in accordance with the signals from the ECM when the system is purging, in order to send the fuel vapor that was absorbed by the charcoal canister into the intake manifold.
ECM
·

Controls the volume of fuel injected, with corrections based primarily on the signal from the air fuel ratio sensor, and minor corrections based on the signal from the oxygen sensor. This control optimizes the air-fuel ratio.

·

Regulates the EGR volume in accordance with the various sensor signals.

·

Controls the purge VSV in accordance with the signals from various sensors, in order to achieve a purge volume that suits the driving conditions.





SYSTEM CONTROL


a.

EGR Control

i.

For the EGR system, a regulated amount of inert gas is allowed to flow into the intake passage, reducing the peak temperature in the engine combustion chamber.


ii.

By sensing the engine driving conditions, the ECM operates the EGR valve assembly and throttle control motor, to regulate the amount of exhaust gas that is recirculated.

W105956E06
5.156,3.875 5.813,3.875 true 5.052,2.531 5.708,2.531 true 5.708,1.615 5.375,1.896 5.375,1.896 5.052,1.896 true 6.438,3.177 6.948,3.396 0.51,0.219 10 false Engine 3.302,2.125 3.667,2.292 0.365,0.167 10 false ECM 4.302,3.781 5.156,4 0.854,0.219 10 false Exhaust Gas 4.25,2.448 5.021,2.833 0.771,0.385 10 false EGR Cooler Assembly 4.323,1.802 5.031,2.229 0.708,0.427 10 false EGR Valve Assembly 4.063,1.25 5.313,1.448 1.25,0.198 10 false EGR Valve Control 4.063,0.813 5.458,1.031 1.396,0.219 10 false Throttle Valve Control 4.063,0.344 6.021,0.563 1.958,0.219 10 false Throttle Position Sensor Signal 0.802,0.344 2.25,0.542 1.448,0.198 10 false Crank Position Sensor 0.219,0.76 2.292,0.958 2.073,0.198 10 false E.F.I. Vacuum Sensor Assembly 0.5,1.094 2.219,1.51 1.719,0.417 10 false Intake Mass Air Flow Meter Sub-assembly 0.292,1.719 2.208,1.969 1.917,0.25 10 false Intake Air Temperature Sensor 0.833,2.115 2.188,2.479 1.354,0.365 10 false E.F.I. Engine Coolant Temperature Sensor 0.375,2.875 1.792,3.229 1.417,0.354 10 false Hybrid Vehicle Control ECU 0.563,3.969 1.719,4.333 1.156,0.365 10 false Accelerator Pedal Sensor Assembly 2.229,3.323 2.896,3.667 0.667,0.344 10 false CAN (Sub bus 15)



b.

Blowby Gas Ventilation System

i.

By introducing blowby gas that has a large amount of HC into the air intake side and burning it again, the system attempts to enhance the emission performance. Returning blowby gas volume is regulated to the appropriate amount corresponding to the engine operating conditions, reducing the engine oil quantity taken away and engine idling speeds.


ii.

The ventilation valve sub-assembly passage returns the blowby gas into the area after the throttle valve in accordance with the intake manifold vacuum.


iii.

When load is low, the passage from the cylinder head cover sub-assembly to the area before the throttle valve increases the air purification performance inside the crankcase by introducing fresh air, and when load is high, the passage circulates the blowby gas together with the ventilation valve sub-assembly side passage due to the intake manifold vacuum.

W105000E10
1.917,1.188 1.677,0.604 1.677,0.604 1.563,0.604 true 1.396,0.521 1.646,0.729 0.25,0.208 10 false *1 2.25,0.563 2.5,0.771 0.25,0.208 10 false *a 4.802,0.542 5.052,0.75 0.25,0.208 10 false *b

Text in Illustration
*1 Ventilation Valve Sub-assembly - -
*a When load is low *b When load is high
V100135

Blowby Gas
V100136

Fresh Air




CONSTRUCTION


a.

Three-Way Catalytic converter (TWC)

i.

TWCs are provided in the exhaust manifold and also in the front exhaust pipe assembly.


ii.

An exhaust manifold with an integrated TWC is used for warm-up of the TWC.


iii.

These TWCs enable improved exhaust emissions with an optimized cell density and wall thickness.

W105987E02
1.125,1.635 1.292,1.167 1.292,1.167 1.417,1.167 true 1.792,1.906 1.958,1.406 1.958,1.406 2.094,1.406 true 1.448,1.073 1.667,1.281 0.219,0.208 10 false *1 2.135,1.313 2.354,1.49 0.219,0.177 10 false *1

Text in Illustration
*1 TWC - -



b.

EGR Valve Assembly and EGR Cooler Assembly

i.

A step motor type EGR valve assembly is used to precisely control the EGR gas flow amount.


ii.

The EGR cooler assembly cools the exhaust gas to improve the EGR efficiency.

W135039E01
5.188,0.646 5.344,0.646 5.344,0.646 5.656,1.083 true 5.948,1.063 6.219,0.646 6.219,0.646 6.365,0.646 true 1.625,4.156 1.771,4.156 1.771,4.156 2.99,3.51 true 1.615,5.125 1.76,5.125 1.76,5.125 3.385,4.479 true 4.26,3.208 4.917,2.583 4.917,2.583 5.083,2.583 true 3.76,5.188 5.594,5.729 5.594,5.729 5.76,5.729 true 1.844,1.229 2.156,1.427 0.313,0.198 10 false *a 1.167,2.229 1.479,2.427 0.313,0.198 10 false *b 4.667,0.5 4.979,0.698 0.313,0.198 10 false *c 5.031,0.573 5.344,0.771 0.313,0.198 10 false *1 6.385,0.552 6.698,0.75 0.313,0.198 10 false *2 1.458,4.073 1.771,4.271 0.313,0.198 10 false *3 5.115,2.5 5.427,2.698 0.313,0.198 10 false *4 1.458,5.042 1.771,5.24 0.313,0.198 10 false *5 5.781,5.625 6.094,5.823 0.313,0.198 10 false *6 3.073,4.323 3.24,4.5 0.167,0.177 10 true A 3.792,4.323 3.948,4.521 0.156,0.198 10 true A

Text in Illustration
*1 Water Passage *2 EGR Gas Passage
*3 EGR Valve Assembly *4 No. 2 EGR Pipe
*5 EGR Cooler Assembly *6 No. 1 EGR Pipe
*a To Intake Manifold *b From Exhaust Manifold
*c A-A Cross Section - -
V100135

EGR Gas - -



c.

E.F.I. Vacuum Sensor Assembly

i.

An E.F.I. vacuum sensor assembly is used to measure the intake manifold pressure for EGR control.


ii.

The E.F.I. vacuum sensor assembly consists of a silicon chip which utilizes the characteristic of a silicon chip that changes its electrical resistance when pressure is applied to it. The sensor converts the pressure into an electrical signal, and sends it to the ECM in an amplified form.

W101304E19
4.625,0.344 4.781,0.344 4.781,0.344 4.917,1.094 true 0.854,2.448 3.146,2.781 2.292,0.333 10 false Manifold Absolute Pressure Sensor 4.615,2.719 5.552,3.052 0.938,0.333 10 false Cross Section 3.823,0.25 4.604,0.479 0.781,0.229 10 false Silicon Chip 1.031,4.458 2.302,4.688 1.271,0.229 10 false Output Voltage (V) 2.573,5.635 3.167,5.969 0.594,0.333 10 false Vacuum 3.125,6.406 4.75,6.74 1.625,0.333 10 false Vacuum Sensor Output 4.615,5.635 5.458,6.188 0.844,0.552 10 false Atmosphere Pressure 3.542,5.635 4.177,6.219 0.635,0.583 10 false Intake Manifold Pressure 2.406,3.802 2.667,4.021 0.26,0.219 10 false 4.2 2.406,4.479 2.677,4.677 0.271,0.198 10 false 2.4 2.406,5.323 2.677,5.531 0.271,0.208 10 false 0.6