Home › Drivetrain › P510 HYBRID TRANSMISSION / TRANSAXLE › HYBRID TRANSAXLE SYSTEM › from 2014.12
NM2170E _52 Drivetrain _056967 P510 HYBRID TRANSMISSION / TRANSAXLE _0277763 HYBRID TRANSAXLE SYSTEM UN GENERAL/CONTROL/DETAILS F

P510 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


SYSTEM CONTROL


a.

Shift Control System

i.

A shift lever position sensor is provided in the transaxle to detect the shift position and sends a corresponding signal to the hybrid vehicle control ECU. Upon receiving this signal, the hybrid vehicle control ECU optimally combines the operation of the engine, MG1 and MG2 in order to produce the respective shift positions (P, R, N, D and B).

X123772E03
1.052,1.229 2.406,1.604 1.354,0.375 10 false Transmission Control Cable Assembly 3.073,1.031 4.021,1.458 0.948,0.427 10 false Hybrid Vehicle Control ECU 5.177,1.802 6.729,2.198 1.552,0.396 10 false Hybrid Vehicle Transaxle Assembly 5.167,0.375 6.542,0.771 1.375,0.396 10 false Inverter with Converter Assembly 3.635,2.823 4.552,3.042 0.917,0.219 10 false CAN (V Bus) 5.448,1.177 6.156,1.375 0.708,0.198 10 false MG ECU 5.448,2.573 5.927,2.76 0.479,0.188 10 false MG1 5.458,3.052 5.885,3.25 0.427,0.198 10 false MG2 2.948,3.208 3.417,3.458 0.469,0.25 10 false ECM 0.313,1.906 1.531,2.302 1.219,0.396 10 false Shift Lever Position Sensor




CONSTRUCTION


a.

Hybrid Vehicle Transaxle Assembly

i.

This hybrid vehicle transaxle assembly consists primarily of Motor Generator No. 1 (MG1), Motor Generator No. 2 (MG2), a compound gear unit, a transmission input damper assembly, a counter gear, a final gear, a differential gear unit and an oil pump.


ii.

This hybrid vehicle transaxle assembly has a 3-shaft configuration. The compound gear unit, a transmission input damper assembly, an oil pump, MG1 and MG2 are provided on the input shaft. The counter driven gear and the final drive gear are provided on the second shaft. The final driven gear and the differential gear unit are provided on the third shaft.


iii.

The engine, MG1 and MG2 are mechanically joined via the compound gear unit.

U159774E03
3.073,0.406 2.979,0.406 2.979,0.406 2.813,1.146 true 4.802,0.406 4.708,0.406 4.708,0.406 4.542,1.146 true 4,0.406 3.896,0.406 3.896,0.406 3.75,1.073 true 5.823,1.083 5.719,1.083 5.719,1.083 4.969,1.5 true 5.844,2.948 5.74,2.948 5.74,2.948 3.99,3.646 true 5.844,3.813 5.74,3.813 5.74,3.813 4.302,4.396 true 2.969,4.417 3.073,4.417 3.073,4.417 3.635,3.865 true 2.51,3.771 2.604,3.771 2.604,3.771 3.417,3.219 true 1.281,2.74 1.385,2.74 1.385,2.74 2.052,2.188 true 3.094,0.313 3.302,0.49 0.208,0.177 10 false *1 4.021,0.323 4.229,0.5 0.208,0.177 10 false *2 4.823,0.323 5.031,0.5 0.208,0.177 10 false *3 5.844,0.99 6.052,1.167 0.208,0.177 10 false *4 5.865,2.865 6.073,3.042 0.208,0.177 10 false *5 5.875,3.729 6.083,3.906 0.208,0.177 10 false *6 2.802,4.333 2.979,4.51 0.177,0.177 10 false *7 2.323,3.688 2.5,3.865 0.177,0.177 10 false *8 1.115,2.646 1.292,2.823 0.177,0.177 10 false *9

Text in Illustration
*1 MG2 *2 Compound Gear Unit
*3 MG1 *4 Transmission Input Damper Assembly
*5 Final Driven Gear *6 Differential Gear Unit
*7 Counter Driven Gear *8 Final Drive Gear
*9 Oil Pump - -



b.

Compound Gear Unit

i.

The compound gear unit consists of the power split planetary gear unit and the motor speed reduction planetary gear unit. Each planetary ring gear is integrated with the compound gear. Furthermore, this compound gear is integrated with a counter drive gear and parking gear.


ii.

The power split planetary gear unit splits the motive force of the engine two ways: one to drive the wheels, and the other to drive MG1, so that MG1 can function as a generator.


iii.

The motor speed reduction planetary gear unit, whose purpose is to reduce MG2 speed, is used to enable the high-speed, high-output MG2 to adapt optimally to the compound gear.

X106906E04
4.01,2.146 4.104,2.146 4.104,2.146 4.479,1.76 true 4.625,2.438 4.719,2.438 4.719,2.438 5.094,2.052 true 6.698,1.51 6.594,1.51 6.594,1.51 6.24,1.917 true 3.646,0.74 3.896,0.948 0.25,0.208 10 false *1 3.844,2.063 4.052,2.229 0.208,0.167 10 false *2 4.458,2.354 4.656,2.521 0.198,0.167 10 false *3 6.719,1.427 6.927,1.604 0.208,0.177 10 false *4

Text in Illustration
*1 Compound Gear Unit *2 Power Split Planetary Gear Unit
*3 Counter Drive Gear (Compound Gear) *4 Motor Speed Reduction Planetary Gear Unit


iv.

The connection of the sun gear, ring gear and carrier of each planetary gear unit is as shown below.

Item Connection
Power Split Planetary Gear Unit Sun Gear MG1
Ring Gear Compound Gear (To Wheels)
Carrier Input Shaft (From Engine)
Motor Speed Reduction Planetary Gear Unit Sun Gear MG2
Ring Gear Compound Gear (To Wheels)
Carrier Fixed

U111624E08
5.698,1.531 5.698,0.656 5.698,0.656 5.948,0.656 true 4.927,1.708 4.927,0.844 4.927,0.844 5.177,0.844 true 1.156,1.031 1.271,1.031 1.271,1.031 1.51,1.385 true 4.49,3.24 4.271,3.24 4.271,3.24 4.271,2.958 true 3.781,2.24 3.271,3.313 3.271,3.313 3.021,3.313 true 3.25,2.083 2.771,2.813 2.771,2.813 2.521,2.813 true 4.781,2.323 5.26,3.135 5.26,3.135 5.448,3.135 true 3.823,1.042 3.823,0.271 3.823,0.271 4.01,0.271 true 3.521,2.323 3.021,3.063 3.021,3.063 2.74,3.063 true 4.427,2.313 4.646,3.104 4.646,3.104 4.854,3.104 true 3.271,0.479 3.51,0.698 0.24,0.219 10 false *3 4.031,0.177 4.292,0.385 0.26,0.208 10 false *5 4.229,0.479 4.458,0.677 0.229,0.198 10 false *4 5.969,0.573 6.188,0.76 0.219,0.188 10 false *2 5.198,0.75 5.448,0.948 0.25,0.198 10 false *6 1,0.948 1.229,1.146 0.229,0.198 10 false *1 4.521,3.156 4.781,3.365 0.26,0.208 10 false *9 4.885,3.01 5.104,3.208 0.219,0.198 10 false *7 2.854,3.229 3.115,3.51 0.26,0.281 10 false *8 2.354,2.729 2.583,2.917 0.229,0.188 10 false *6 2.583,2.979 2.802,3.156 0.219,0.177 10 false *7 5.479,3.042 5.698,3.229 0.219,0.188 10 false *8

Text in Illustration
*1 MG1 *2 MG2
*3 Power Split Planetary Gear Unit *4 Motor Speed Reduction Planetary Gear Unit
*5 Counter Drive Gear *6 Sun Gear
*7 Ring Gear *8 Carrier
*9 Counter Driven Gear - -



c.

Transmission Input Damper Assembly

i.

A transmission input damper assembly that consists of a coil spring with low-twist characteristics is used in order to absorb the torque fluctuation in the motive force of the engine. The torque limiter uses a dry-type, single-plate friction material. Through the use of these parts, a damper construction that excels in absorbing the vibrations of the engine motive force has been achieved.

X106907E04
4.26,0.156 6.823,3.667 2.563,3.51 2.271,1.479 3.177,0.479 3.177,0.479 3.271,0.479 true 5.26,0.938 4.656,0.938 true 5.167,1.448 4.656,1.448 true 3.302,0.396 3.531,0.563 0.229,0.167 10 false *1 4.5,0.854 4.719,1.031 0.219,0.177 10 false *2 4.313,0.198 4.552,0.385 0.24,0.188 10 false *a 4.5,1.365 4.708,1.552 0.208,0.188 10 false *1

Text in Illustration
*1 Coil Spring *2 Torque Limiter
*a Transmission Input Damper Assembly Cross Section - -
V100135

From Engine - -



d.

Oil Pump Mechanism

i.

For lubrication of the compound gear unit and also for supplying oil to MG1 and MG2, a new shape, compact internal oil pump gear without crescent shaped seal is used to reduce the drive loss of the oil pump.

X106908E04
3.833,1.76 3.958,1.76 3.958,1.76 4.146,1.49 true 5.083,1.438 4.99,1.438 4.99,1.438 4.813,1.729 true 4.948,2.385 5.042,2.385 5.042,2.385 5.198,2.083 true 6.417,1.875 6.302,1.875 6.302,1.875 6.125,2.063 true 3.677,1.677 3.896,1.854 0.219,0.177 10 false *1 5.104,1.354 5.333,1.531 0.229,0.177 10 false *2 4.792,2.313 5.01,2.479 0.219,0.167 10 false *3 6.438,1.792 6.635,1.979 0.198,0.188 10 false *4

Text in Illustration
*1 Oil Pump Drive Shaft *2 Oil Pump Drive Rotor
*3 Oil Pump Driven Rotor *4 Oil Pump Cover



e.

Oil Sling Type Lubrication Mechanism

i.

An oil sling type lubrication mechanism has been provided, which lubricates the gears and bearings by catching and transferring the oil released via the rotation of the final driven gear and counter driven gear. This lubrication mechanism helps optimize the discharge amount of oil from the oil pump that is driven by the engine power, contributing to the drive loss reduction.


ii.

2 oil catch tanks have been provided to temporarily store oil that is transferred from 2 channels. One that temporarily stores oil that is pumped up by the oil pump and is used to supply oil to the motor generator, and the other that temporarily stores oil that is fed by the rotation of the final driven gear and counter driven gear and is used to lubricate the compound gear unit.


iii.

The oil catch tank for motor generator oil supply pumps up oil that accumulates in the transaxle case and the lower portion of the transaxle housing via the oil pump, feeding oil to the motor generator.


iv.

The oil catch tank for the compound gear unit lubrication collects oil via the rotation of the final driven gear and counter driven gear, routing the oil to the lubrication holes provided in the transaxle case and transaxle housing to feed oil to the compound gear unit.


v.

By employing the oil catch tanks to supply oil to the motor generator and to lubricate the compound gear unit, the oil surface levels inside the transaxle case and transaxle housing can be regulated to the optimal level while the vehicle is driven, reducing the oil stirring loss caused by the final driven gear and counter driven gear.

X106909E04
4.938,2.646 5.24,3.313 5.24,3.313 5.354,3.313 true 2.281,1.26 1.885,0.615 1.885,0.615 1.75,0.615 true 2.594,0.99 2.219,0.281 2.219,0.281 2.083,0.281 true 2.927,0.865 2.552,0.135 2.552,0.135 2.417,0.135 true 3.354,0.979 3.781,0.167 3.781,0.167 3.906,0.167 true 4.708,1.375 5.156,0.5 5.156,0.5 5.281,0.5 true 3.365,1.083 4.344,0.26 4.344,0.26 4.458,0.26 true 1.573,0.531 1.781,0.708 0.208,0.177 10 false *a 4.479,0.177 4.688,0.354 0.208,0.177 10 false *a 1.906,0.177 2.115,0.354 0.208,0.177 10 false *b 3.927,0.073 4.135,0.25 0.208,0.177 10 false *c 2.26,0.052 2.469,0.229 0.208,0.177 10 false *1 5.302,0.406 5.51,0.583 0.208,0.177 10 false *2 5.375,3.229 5.583,3.406 0.208,0.177 10 false *3

Text in Illustration
*1 Oil Supply Pipe *2 Counter Driven Gear
*3 Final Driven Gear - -
*a Oil Catch Tank for Compound Gear Unit Lubrication *b Oil Catch Tank for Oil Supply
*c Lubrication Hole of the Compound Gear Unit - -
V100135

Oil Flow
V100136

Gear Rotation Direction



f.

Oil Supply Mechanism

i.

An oil supply mechanism has been provided for the MG1 and MG2, which feeds some of the oil, which is discharged by the oil pump located on the input shaft, to the MG1 and MG2.


ii.

The oil discharged by the oil pump is routed to the two channels; a lubrication path for the compound gear unit and an oil supply path for the MG1 and MG2. For the oil that flows through the oil supply path, it is transferred to the upper portion of the transaxle running through the external oil path provided between the oil pump cover and the transaxle case. After that, the oil flows through the oil pipe located in the upper area of the MG1 and MG2, reaching the MG1 and MG2.


iii.

The distribution oil amount has been optimized to make the oil supply to the MG1 and MG2 stable.

X108173E05
1.01,3.042 6.615,6.531 5.604,3.49 4.26,0.844 4.74,0.219 4.74,0.219 4.865,0.219 true 4.5,1.99 5.031,2.74 5.031,2.74 5.188,2.74 true 3.25,1.365 2.448,2.75 2.448,2.75 2.313,2.75 true 2.917,5.302 3.073,6.135 3.073,6.135 3.208,6.135 true 5.01,5.302 5.167,6.135 5.167,6.135 5.313,6.135 true 2.885,4.521 2.635,3.396 2.635,3.396 2.469,3.396 true 3.646,4.167 3.49,3.396 3.49,3.396 3.313,3.396 true 4.938,4.521 4.74,3.385 4.74,3.385 4.583,3.385 true 4.896,0.125 5.135,0.333 0.24,0.208 10 false *1 5.219,2.646 5.469,2.833 0.25,0.188 10 false *2 2.156,2.656 2.344,2.844 0.188,0.188 10 false *a 2.313,3.323 2.5,3.51 0.188,0.188 10 false *3 1.156,3.125 1.417,3.344 0.26,0.219 10 false *b 3.24,6.052 3.427,6.24 0.188,0.188 10 false *4 5.333,6.052 5.563,6.25 0.229,0.198 10 false *5 4.427,3.302 4.615,3.49 0.188,0.188 10 false *3 3.156,3.323 3.344,3.51 0.188,0.188 10 false *a

Text in Illustration
*1 Transaxle Case *2 Oil Pump Cover
*3 Oil Pipe *4 MG2
*5 MG1 - -
*a External Oil Path *b Oil Supply Mechanism (Cross Section)
V100135

Oil Flow - -



g.

Shift Lever Position Sensor

i.

The shift lever position sensor sends the P, R, N, D and B position signals to the hybrid vehicle control ECU.


ii.

The hybrid vehicle control ECU transmits signals to the combination meter assembly for the shift position display (P, R, N, D and B) in response to the signals received from the sensor.

X123769E03
4.167,3.448 4.167,3.021 false 3.542,1.729 4.729,1.948 1.188,0.219 10 false CAN (Sub bus 15) 1.417,0.177 1.771,0.344 0.354,0.167 10 false PNB 1.417,0.552 1.771,0.719 0.354,0.167 10 false DB2 1.406,0.927 1.76,1.094 0.354,0.167 10 false DB1 1.406,1.292 1.552,1.458 0.146,0.167 10 false N 0.76,3.156 0.906,3.323 0.146,0.167 10 false N 0.542,3.156 0.688,3.323 0.146,0.167 10 false D 0.323,3.156 0.469,3.323 0.146,0.167 10 false B 1.406,1.667 1.542,1.833 0.135,0.167 10 false R 0.969,3.156 1.104,3.323 0.135,0.167 10 false R 1.406,2.042 1.667,2.208 0.26,0.167 10 false PR 1.417,2.406 1.542,2.573 0.125,0.167 10 false P 1.198,3.156 1.323,3.323 0.125,0.167 10 false P 1.417,2.885 1.635,3.052 0.219,0.167 10 false +B 0.063,3.406 1.813,3.594 1.75,0.188 10 false Shift Lever Position Sensor 2.323,1.438 3.26,1.823 0.938,0.385 10 false Hybrid Vehicle Control ECU 4.823,0.094 6.75,0.323 1.927,0.229 10 false Combination Meter Assembly 4.823,1.448 5.198,1.625 0.375,0.177 10 false ECM 5,0.698 6.406,0.927 1.406,0.229 10 false Shift Position Display 4.813,2 6.906,2.219 2.094,0.219 10 false Inverter with Converter Assembly 5,2.594 6.385,2.969 1.385,0.375 10 false Motor Generator ECU (MG ECU) 3.667,0.375 4.552,0.594 0.885,0.219 10 false CAN (V Bus) 3.438,3.438 4.865,3.635 1.427,0.198 10 false Serial Communication



h.

Parking Lock Mechanism

i.

The parking lock mechanism consists of a parking lock pawl and a parking lock gear which is integrated with the compound gear.


ii.

When the driver moves the shift lever to P, the parking lock pawl engages with the parking lock gear.

X106911E03
1.604,0.844 1.708,0.844 1.708,0.844 3.781,2.438 true 5.667,0.688 5.573,0.688 5.573,0.688 4.271,2.281 true 1.438,0.76 1.667,0.938 0.229,0.177 10 false *1 5.698,0.594 5.948,0.802 0.25,0.208 10 false *2

Text in Illustration
*1 Parking Lock Gear *2 Parking Lock Pawl



i.

Shift Lock System

i.

The shift lock system is controlled by the shift lock control ECU.


ii.

The shift lock mechanism prevents the shift lever from being moved to any position other than P, unless the power switch is turned on (IG), and the brake pedal is depressed is stowed. This mechanism helps to prevent unintentional acceleration.


iii.

The shift lock system mainly consists of the shift lock control ECU and shift lock solenoid.

X106913E02
0.594,2.292 1.729,2.51 1.135,0.219 10 false No.1 IG1 Relay 2.958,1.563 4.094,1.938 1.135,0.375 10 false Shift Lock Control ECU 5.448,0.917 6.115,1.281 0.667,0.365 10 false Shift Lock Solenoid 5.448,2.292 6.208,2.656 0.76,0.365 10 false P Detection Switch 4.781,3.156 6.688,3.385 1.906,0.229 10 false Shift Lock Solenoid Assembly 0.521,0.927 2.281,1.156 1.76,0.229 10 false Stop Light Switch Assembly


iv.

The shift lock control ECU uses the P detection switch to detect the shift lever position, and receives inputs from the stop light switch assembly and power switch. Upon receiving these signals, the shift lock control ECU turns on the shift lock solenoid in order to release the shift lock.




OPERATION


a.

Motive Force Transmission Path

i.

The motive force created by the engine and MG2 is transmitted by the counter drive gear of the compound gear unit, the counter driven gear, the final drive gear, and then the differential gear unit, in order to drive the front wheels.

U111625E05
2.958,1.229 2.958,0.333 2.958,0.333 3.135,0.333 true 1.906,1.24 1.906,0.344 1.906,0.344 2.083,0.344 true 4.24,0.323 4.115,0.323 4.115,0.323 4.115,0.76 true 5.469,1.219 5.469,0.333 5.469,0.333 5.656,0.333 true 6.125,1.292 6.125,0.333 6.125,0.333 6.302,0.333 true 3.625,3.01 2.885,3.01 true 5.198,3.083 4.5,3.083 true 4.563,3.844 3.948,3.844 true 3.031,3.688 3.031,4.365 3.031,4.365 3.208,4.365 true 4.365,2.146 5.01,2.865 5.01,2.865 5.198,2.865 true 0.76,1.031 0.76,0.323 0.76,0.323 0.938,0.323 true 3.729,1.771 3.115,2.365 3.115,2.365 2.896,2.365 true 4.115,1.885 3.104,2.802 3.104,2.802 2.875,2.802 true 4.969,1.49 4.969,0.344 4.969,0.344 5.167,0.344 true 4.854,2.021 5,2.385 5,2.385 5.188,2.385 true 3.76,1.969 3.115,2.563 3.115,2.563 2.896,2.563 true 4.615,1.938 5.01,2.583 5.01,2.583 5.198,2.583 true 3.156,0.25 3.375,0.479 0.219,0.229 10 false *3 4.26,0.25 4.479,0.479 0.219,0.229 10 false *4 5.688,0.25 5.906,0.479 0.219,0.229 10 false *6 5.188,0.25 5.406,0.479 0.219,0.229 10 false *5 6.313,0.25 6.531,0.479 0.219,0.229 10 false *7 5.219,2.76 5.479,2.99 0.26,0.229 10 false *10 5.219,2.292 5.438,2.521 0.219,0.229 10 false *9 5.219,2.49 5.438,2.719 0.219,0.229 10 false *8 2.719,2.719 2.938,2.948 0.219,0.229 10 false *9 2.719,2.281 2.938,2.51 0.219,0.229 10 false *5 2.719,2.49 2.938,2.719 0.219,0.229 10 false *8 5.219,3 5.5,3.229 0.281,0.229 10 false *12 4.583,3.75 4.833,3.979 0.25,0.229 10 false *13 3.229,4.281 3.51,4.51 0.281,0.229 10 false *14 2.667,2.927 2.906,3.156 0.24,0.229 10 false *11 2.104,0.25 2.323,0.479 0.219,0.229 10 false *2 0.958,0.229 1.177,0.458 0.219,0.229 10 false *1

Text in Illustration
*1 Engine *2 Transmission Input Damper Assembly
*3 MG1 *4 Compound Gear Unit
*5 Sun Gear *6 MG2
*7 Oil Pump *8 Ring Gear
*9 Carrier *10 Counter Drive Gear (Compound Gear)
*11 Final Drive Gear *12 Counter Driven Gear
*13 Final Driven Gear *14 Differential Gear Unit



b.

Engine Motive Force and MG2 Motive Force Transmission Path

i.

The engine motive force, which is input by the carrier, is transmitted to the ring gear. The motive force of MG2 is transmitted to the ring gear via the motor speed reduction planetary gear unit. The sum of these two motive forces is transmitted by the compound gear in order to drive the wheels.

U111627E03
2.167,0.948 2.167,0.271 2.167,0.271 2.333,0.271 true 5.958,0.948 5.958,0.271 5.958,0.271 6.125,0.271 true 3.615,0.156 3.875,0.438 0.26,0.281 10 false *3 4.458,0.156 4.719,0.438 0.26,0.281 10 false *4 6.177,0.188 6.438,0.469 0.26,0.281 10 false *2 2.365,0.177 2.625,0.458 0.26,0.281 10 false *1

Text in Illustration
*1 MG1 *2 MG2
*3 Power Split Planetary Gear Unit *4 Motor Speed Reduction Planetary Gear Unit
V100135

Rotation Direction
V100136

From Engine
V100137

From MG2
V100138

To Wheels



c.

MG2 Motive Force Transmission Path

i.

The motive force of MG2 is transmitted via the sun gear and is output to the ring gear in order to drive the wheels. The carrier of the motor speed reduction planetary gear unit is fixed. As a result, the motor speed reduction planetary gear unit reduces the speed of MG2, increasing torque in accordance with a set gear ratio. The direction of rotation of MG2 changes according to whether the vehicle is travelling forward or in reverse.

U111628E03
1.906,0.979 1.906,0.302 1.906,0.302 2.073,0.302 true 5.583,0.979 5.583,0.302 5.583,0.302 5.76,0.302 true 2.104,0.208 2.365,0.49 0.26,0.281 10 false *1 3.354,0.125 3.615,0.406 0.26,0.281 10 false *3 4.208,0.125 4.469,0.406 0.26,0.281 10 false *4 5.781,0.208 6.042,0.49 0.26,0.281 10 false *2

Text in Illustration (Driving Forward:)
*1 MG1 *2 MG2
*3 Power Split Planetary Gear Unit *4 Motor Speed Reduction Planetary Gear Unit
V100135

Rotation Direction
V100136

From MG2
V100137

To Wheel - -

U111629E03
1.958,0.979 1.958,0.229 1.958,0.229 2.125,0.229 true 5.635,0.979 5.635,0.229 5.635,0.229 5.802,0.229 true 3.406,0.156 3.667,0.438 0.26,0.281 10 false *3 4.25,0.156 4.51,0.438 0.26,0.281 10 false *4 2.156,0.135 2.417,0.417 0.26,0.281 10 false *1 5.823,0.135 6.083,0.417 0.26,0.281 10 false *2

Text in Illustration (Driving in Reverse:)
*1 MG1 *2 MG2
*3 Power Split Planetary Gear Unit *4 Motor Speed Reduction Planetary Gear Unit
V100135

Rotation Direction
V100136

From MG2
V100137

To Wheel - -



d.

Engine Motive Force Transmission Path

i.

The engine motive force, which is input by the carrier, is transmitted to the sun gear. Thus, motive force is transmitted in order to operate MG1 as a generator.

U111630E03
2.146,1 2.146,0.271 2.146,0.271 2.323,0.271 true 5.833,1 5.833,0.271 5.833,0.271 6,0.271 true 3.604,0.167 3.865,0.448 0.26,0.281 10 false *3 4.448,0.177 4.708,0.458 0.26,0.281 10 false *4 2.354,0.177 2.615,0.458 0.26,0.281 10 false *1 6.021,0.177 6.281,0.458 0.26,0.281 10 false *2

Text in Illustration
*1 MG1 *2 MG2
*3 Power Split Planetary Gear Unit *4 Motor Speed Reduction Planetary Gear Unit
V100135

Rotation Direction
V100136

From Engine
V100137

To MG1 - -



e.

MG1 Motive Force Transmission Path

i.

The motive force of MG1 is transmitted via the sun gear and is output to the carrier. Thus, motive force is transmitted in order to start the engine.

U111631E03
2.146,0.906 2.146,0.177 2.146,0.177 2.323,0.177 true 5.833,0.906 5.833,0.177 5.833,0.177 6,0.177 true 3.594,0.104 3.854,0.385 0.26,0.281 10 false *3 4.438,0.104 4.698,0.385 0.26,0.281 10 false *4 2.344,0.083 2.604,0.365 0.26,0.281 10 false *1 6.021,0.083 6.281,0.365 0.26,0.281 10 false *2

Text in Illustration
*1 MG1 *2 MG2
*3 Power Split Planetary Gear Unit *4 Motor Speed Reduction Planetary Gear Unit
V100135

Rotation Direction
V100136

From MG1
V100137

To Engine - -