Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › from 2014.12
NM2170E _54 Brake _056974 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0277770 BRAKE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  GENERAL  


OUTLINE


a.

The brake actuator and the skid control ECU are integrated and a hydraulic brake booster is provided, thus optimizing the hydraulic circuit and offering a weight reduction.


b.

The brake control functions (ABS with EBD, Brake Assist, TRC, VSC and Hill-start Assist Control) are provided.


c.

An electronically controlled brake system is used to control the hydraulic pressure at the 4 wheels.


d.

A regenerative brake cooperative control is used.


e.

A VSC OFF switch is used.



MAIN FEATURES


a.

Electronically Controlled Brake System

i.

In this system, the conventional brake booster portion has been discontinued. Instead, it consists of hydraulic brake booster, brake actuator and brake booster pump assembly.


ii.

During normal braking, the fluid pressure generated by the hydraulic brake booster does not directly actuate the wheel cylinders, but serves as a hydraulic pressure signal. Instead, the actual control pressure is obtained by regulating the fluid pressure of the brake booster pump assembly, which actuates the wheel cylinders.


iii.

When the skid control ECU detects a fault in the system, brake force can be ensured by applying the brake using the fluid pressure boosted by the hydraulic brake booster.

X108144E12
5.385,5.479 5.844,4.802 5.844,4.802 5.969,4.802 true 5.042,5.813 4.479,6.99 4.479,6.99 4.396,6.99 true 2.521,0.927 3.354,0.281 3.354,0.281 3.438,0.281 true 4.521,2.604 6.385,2.885 1.865,0.281 10 false Hybrid Vehicle Control ECU 6.01,4.719 6.854,5.188 0.844,0.469 10 false Regenerative Brake Force 3.365,6.917 4.375,7.385 1.01,0.469 10 false Hydraulic Brake Force 4.979,7.427 5.823,7.688 0.844,0.26 10 false Brake Force 2.323,5.24 3.938,5.448 1.615,0.208 10 false Hydraulic Control Portion 0.5,5.25 1.563,5.625 1.063,0.375 10 false Hydraulic Power Source Portion 5.563,0.198 6.865,0.427 1.302,0.229 10 false : Electrical Signal 5.563,0.469 6.885,0.698 1.323,0.229 10 false : Fluid Pressure 0.51,2.625 1.729,2.844 1.219,0.219 10 false Skid Control ECU 1.583,1.542 2.615,1.958 1.031,0.417 10 false Master Cylinder Pressure Sensor 3.469,0.198 4.719,0.594 1.25,0.396 10 false Brake Pedal Stroke Sensor 0.51,3.167 2.906,3.521 2.396,0.354 10 false - Normal Brake, ABS with EBD, Brake Assist, TRC, and VSC 0.51,3.896 3.073,4.125 2.563,0.229 10 false - Regenerative Brake Cooperative Control 0.5,5.885 1.865,6.302 1.365,0.417 10 false - Generates hydraulic power using the pump 2.323,5.719 4.427,6.24 2.104,0.521 10 false Hydraulic power is adjusted to the required braking force, and distributes it to each wheel 4.521,3.063 5.969,3.281 1.448,0.219 10 false - Regenerative Brake



b.

Regenerative Brake Cooperative Control

i.

Regenerative braking consists of a resistance force that is generated at the rotational axle in the reverse direction of the rotation of the generator (MG2) that is generating electricity. The greater the generated amperage (battery charging amperage), the greater will be the resistance force.

X101531E05
4.146,0.448 4.333,0.688 0.188,0.24 10 false *a 4.188,1.198 4.375,1.438 0.188,0.24 10 false *b 4.073,2.542 4.375,2.719 0.302,0.177 10 false *3 2.51,2.531 2.813,2.708 0.302,0.177 10 false *4 0.406,2.563 0.708,2.74 0.302,0.177 10 false *3 4.813,1.75 5.115,1.927 0.302,0.177 10 false *1 5.958,1.719 6.26,1.896 0.302,0.177 10 false *2 6.198,2.542 6.5,2.719 0.302,0.177 10 false *4 5.354,3.333 5.656,3.51 0.302,0.177 10 false *c 2.292,1.719 2.594,1.896 0.302,0.177 10 false *2 1.146,1.75 1.448,1.927 0.302,0.177 10 false *1 0.448,0.479 0.677,0.688 0.229,0.208 10 false *a 0.448,1.198 0.677,1.406 0.229,0.208 10 false *b 1.656,3.333 1.885,3.542 0.229,0.208 10 false *c

Text in Illustration
*1 MG1 *2 Inverter
*3 Engine *4 MG2
*a Rotating direction to electricity generation *b Resistance
*c Brake Force - -


ii.

The drive wheels and MG2 are joined mechanically. When the drive wheels rotate MG2 and cause it to operate as a generator, a regenerative brake force of MG2 is transmitted to the drive wheels. Based on the signals from the skid control ECU, this force is controlled by the hybrid system, which controls the generation of electricity.


iii.

The regenerative brake cooperative control does not rely solely on the braking force of the hydraulic brake system to supply the brake force required by the driver. Instead, by effecting cooperative control with the hybrid system, this control provides a joint braking force provided by the regenerative braking and the hydraulic braking. As a result, this control minimizes the loss of the kinetic energy associated with the normal hydraulic braking, and recovers this energy by converting it into electrical energy.


iv.

The apportioning of the brake force between the hydraulic braking and the regenerative braking varies by the vehicle speed and time.


v.

The apportioning of the brake force between the hydraulic braking and the regenerative braking is accomplished by controlling the hydraulic braking so that the total brake force of the hydraulic braking and the regenerative braking matches the brake force required by the driver.


vi.

If the regenerative braking becomes inoperative due to a malfunction in the hybrid system, the brake system effects control so that the entire brake force required by the driver is supplied with the hydraulic brake system.

X101475E26
2.573,0.313 2.75,0.313 2.75,0.313 3.365,1.24 true 4.594,0.854 4.448,0.854 4.448,0.854 4.229,1.125 true 1.25,1.635 1.781,2.021 0.531,0.385 10 false Braking Force 1.417,0.208 2.542,0.563 1.125,0.354 10 false Hydraulic Braking Force 4.625,0.76 5.708,1.031 1.083,0.271 10 false Driver's Demand 3.406,2.354 4.75,2.729 1.344,0.375 10 false Regenerative Braking Force 3.26,2.927 3.656,3.156 0.396,0.229 10 false Time 2.188,3.333 4.823,3.688 2.635,0.354 10 false Changes in Braking Force Apportionment




PRECAUTION


a.

When brake control system is activated, the brake pedal could shudder, which is a normal occurrence of the system in operation and should not be considered as a malfunction.