Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › 2014.12–2015.11
NM2170E _54 Brake _056974 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0277770 BRAKE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function
Brake Booster Pump Assembly
·

Consisting of a pump, pump motor and accumulator, the hydraulic power source portion generates and stores the hydraulic pressure, which the skid control ECU uses for controlling braking.

·

The relief valve is installed in the hydraulic brake booster.

·

The accumulator pressure sensor is installed in the brake actuator.


Brake Booster with Master Cylinder Assembly Brake Actuator
·

Consists of 4 switching solenoid valves, 2 pressure control solenoid valves, 8 control solenoid valves.

·

Changes the brake fluid path based on the signals from the skid control ECU during the operations of the ABS with EBD, Brake Assist, TRC, VSC and Hill-start Assist Control in order to control the fluid pressure that is applied to the wheel cylinders.


Hydraulic Brake Booster
·

Generates hydraulic pressure in accordance with the amount of effort applied to the brake pedal by the driver.

·

When a malfunction occurs in the brake system, the hydraulic brake booster supplies the fluid pressure (which is generated by the brake pedal effort) directly to the wheel cylinders.


Relief Valve (Built into the skid control ECU) Returns the brake fluid to the reservoir tank to prevent excessive pressure if the pump operates continuously due to a malfunction of the accumulator pressure sensor.
Solenoid Relay (Built into the skid control ECU) Supply or cut off power to solenoid valves in the brake actuator.
Pump Motor Relays (Built into the skid control ECU) Normally supplies power to the pump motor using 2 out of 3 relays. Ensures power to the pump motor by using the other relay if the skid control ECU detects a malfunction.
Brake Pedal Stroke Simulator Generates a pedal stroke during braking in accordance with the driver's pedal effort.
Skid Control ECU
·

Monitors the driving conditions of the vehicle in accordance with the signals received from the sensors and through cooperative control with the hybrid vehicle control ECU and EPS ECU calculates the required amount of braking force, and controls the brake actuator.

·

Judges the vehicle driving condition based on signals from each sensor, and controls ABS with EBD, Brake Assist, TRC, VSC and Hill-start Assist Control.

·

Operates the brake booster pump assembly to control accumulator pressure based on accumulator pressure sensor signal.


Brake Master Cylinder Reservoir Assembly Brake Fluid Level Warning Switch Detects the low brake fluid level.
Brake Pedal Stroke Sensor Assembly Directly detects the extent of the brake pedal stroke operated by the driver.
Airbag Sensor Assembly Yaw Rate and Acceleration Sensor
·

Detects the vehicle's yaw rate.

·

Detects the vehicle's acceleration in the forward, rearward and lateral.


Spiral Cable with Sensor Sub-assembly Steering Angle Sensor Detects the steering direction and angle of the steering wheel.
Front Speed Sensor RH Detects the wheel speed of each of 4 wheels.
Front Speed Sensor LH
Rear Speed Sensor (Rear Axle Hub and Bearing Assembly RH)
Rear Speed Sensor (Rear Axle Hub and Bearing Assembly LH)
VSC OFF Switch Enables the driver to select the "Normal Mode", "TRC-OFF Mode" or "VSC-OFF Mode".
Combination Meter Assembly ABS Warning Light Lights up to alert the driver when the skid control ECU detects the malfunction in the ABS, EBD or Brake Assist.
Brake Warning Light/Yellow (Minor Malfunction) Lights up to alert the driver when a minor malfunction occurs in the brake system, which does not affect the braking force (such as a malfunction in the regenerative braking).
Brake Warning Light/Red (Malfunction)
·

Lights up to alert the driver when the skid control ECU detects the malfunction in the apportioning of the brake.

·

Lights up to inform the driver when the parking brake is on or the brake fluid level is low.


Slip Indicator Light
·

Blinks to inform the driver when the ABS, the TRC or the VSC is operated.

·

Lights up to alert the driver in the event of malfunction of the TRC, VSC or the Hill-start Assist Control.


VSC OFF Indicator Light Illuminates to inform the driver when VSC OFF mode is selected.
Multi-information Display Displays the information message when TRC OFF mode is selected.
Buzzer This buzzer sounds continuously to inform the driver when there is a malfunction in the hydraulic pressure or a failure in the power supply.
Hybrid Vehicle Control ECU
·

Actuates the regenerative braking on receiving signal from the skid control ECU.

·

Sends the actual regenerative brake control value to the skid control ECU.

·

Controls the motive force based on an output control request signal received from the skid control ECU while the TRC or VSC is operating.


Main Body ECU (Multiplex Network Body ECU) Detects the parking brake signal and outputs it to the skid control ECU via CAN communication.


OPERATING CONDITION


a.

Hill-start Assist Control

i.

Hill-start Assist Control Activation Conditions

·

The skid control ECU judges if the vehicle is on an uphill incline based on signals from the deceleration sensor, and activates Hill-start Assist Control when the vehicle is started with all of the following conditions met.


Control Activation Conditions
·

The shift lever is in any position other than P or N (Forward climbing and backward climbing).

·

The vehicle is at a standstill.

·

The accelerator pedal is not depressed.

·

The parking brake is released.




ii.

Hill-start Assist Control Cancelation Conditions

·

If any of the following conditions is met, Hill-start Assist Control operation is canceled.


Control Cancelation Conditions
·

The shift lever is moved to P or N.

·

The accelerator pedal is depressed.

·

The parking brake is operated.

·

Approximately 2 seconds elapse since the operation started.






SYSTEM CONTROL


a.

Control List

i.

The brake control system (ABS with EBD, Brake Assist, TRC and VSC) has the following controls:

Control Outline
Electronically Controlled Brake System Upon receiving signals from the skid control ECU, this system effects hydraulic pressure control at the 4 wheels.
Regenerative Brake Cooperative Control Controls hydraulic braking in order to recover electrical energy by utilizing the regenerative braking of the hybrid system as much as possible.
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
Electronic Brake Force Distribution (EBD) The EBD control utilizes ABS, realizing proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle stability.
Brake Assist The primary purpose of Brake Assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping draw the vehicle's braking performance.
Traction Control (TRC) The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.
Vehicle Stability Control (VSC) The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, during cornering.
Hill-start Assist Control When starting uphill, this control maintains the brake hydraulic pressure to the 4 wheels, in order to momentarily prevent the vehicle from descending backward.
Motive Force Control during TRC or VSC Operation Transmits a motive force control signal from the skid control ECU to the hybrid vehicle control ECU to limit the motive force while the TRC or VSC is being activated.



b.

Anti-lock Brake System (ABS)

i.

The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.

X101654E10
4.948,0.74 5.271,1.01 0.323,0.271 10 false *A 3.74,2.281 3.969,2.479 0.229,0.198 10 false *a 4.948,1.594 5.302,2 0.354,0.406 10 false *B

Text in Illustration
*A With ABS *B Without ABS
*a Brake Operation - -



c.

Electronic Brake Force Distribution (EBD)

i.

This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to ensure excellent braking performance.

X100697E34
1.948,1.719 1.781,1.719 1.781,1.719 1.781,2.563 true 4.917,1.406 4.74,1.406 4.74,1.406 4.74,2.375 true 2.406,2.635 2.229,2.635 2.229,2.635 2.063,2.49 true 5.417,2.604 5.24,2.604 5.24,2.604 5.073,2.458 true 0.594,2.135 1.333,2.542 0.74,0.406 10 false Rear Brake Force 3.583,2.135 4.344,2.781 0.76,0.646 10 false Rear Brake Force 1.99,1.635 3.125,2.031 1.135,0.396 10 false Ideal Brake Force Distribution 4.958,1.323 6.083,1.708 1.125,0.385 10 false Ideal Brake Force Distribution 2.438,2.542 3.229,2.854 0.792,0.313 10 false EBD Control 5.448,2.531 6.292,2.74 0.844,0.208 10 false EBD Control 1.729,2.917 2.885,3.24 1.156,0.323 10 false Front Brake Force 4.74,2.917 5.896,3.24 1.156,0.323 10 false Front Brake Force 1.667,3.281 3.01,3.625 1.344,0.344 10 false Without Load in Rear 4.781,3.292 5.927,3.625 1.146,0.333 10 false With Load in Rear


ii.

During cornering braking, this function controls the brake force that acts on the left and right wheels in accordance with the vehicle conditions at that time. This ensures vehicle stability and excellent braking performance.

X101505

Text in Illustration
V100135

Brake Force
V100138

Control Moment



d.

Brake Assist

i.

In the brake assist, based on the signals from the master cylinder pressure sensor, the skid control ECU calculates the speed and the amount of the brake pedal application and then determines the intention of the driver to make an emergency braking. If the skid control ECU determines that the driver intends the emergency braking, this function activates the brake actuator to increase the brake fluid pressure, which increases the brake force.

X100968E27
2.896,0.115 4.094,0.333 1.198,0.219 10 false Skid Control ECU 2.688,0.792 3.708,1.188 1.021,0.396 10 false Master Cylinder Pressure Signal 0.292,1.917 1.656,2.406 1.365,0.49 10 false The fluid pressure is increased by the skid control ECU 4.5,0.781 6.208,1.188 1.708,0.406 10 false Brake Pedal Stroke Sensor Assembly Signal 1.302,4.188 2.146,4.396 0.844,0.208 10 false Brake Force 4.438,4.219 5.74,4.438 1.302,0.219 10 false With Brake Assist 4.396,4.896 5.875,5.104 1.479,0.208 10 false Without Brake Assist 5.115,5.25 5.531,5.427 0.417,0.177 10 false Time 0.521,0.833 2.375,1.063 1.854,0.229 10 false Fluid Pressure Control Signal



e.

Traction Control (TRC)

i.

If the driver presses the accelerator pedal aggressively when starting off or accelerating on a slippery surface, the drive wheel could slip due to the excessive amount of torque that is generated. The adjustment of the motive force and the control of the hydraulic brakes of the drive wheels accomplished by hybrid system allow the TRC function to help minimize the slippage of the drive wheels, and generates the drive force that is appropriate for the road surface conditions.


ii.

For example, a comparison may be made between two vehicles, one with the TRC function and the other without. If the driver of each vehicle operates the accelerator pedal in a rough manner while driving over a surface with different surface friction characteristics, the drive wheel on the slippery surface could slip as illustrated. As a result, the vehicle could become unstable. However, when the vehicle is equipped with the TRC function, the skid control ECU instantly determines the state of the vehicle and operates the brake actuator in order to apply the brake of the slipping drive wheel. Simultaneously, the skid control ECU effects cooperative control with the hybrid vehicle control ECU, in order to adjust the motive force. Thus, this function can constantly maintain a stable vehicle posture.

X104755E10
4.229,0.302 4.115,0.302 4.115,0.302 3.896,0.646 true 5.375,0.792 5.26,0.792 5.26,0.792 5.042,1.125 true 5.198,2.073 5.063,2.073 5.063,2.073 5.063,3.323 true 5.396,3.052 5.823,2.031 5.823,2.031 5.958,2.031 true 5.646,3.74 6.24,3.219 6.24,3.219 6.344,3.219 true 4.896,3.865 4.125,4.344 4.125,4.344 4,4.344 true 3.99,4.698 4.115,4.698 4.115,4.698 5.24,3.885 true 2.51,2.604 2.708,2.792 0.198,0.188 10 false *B 4.271,0.198 4.469,0.385 0.198,0.188 10 false *a 5.396,0.698 5.594,0.885 0.198,0.188 10 false *a 1.344,2.104 1.542,2.292 0.198,0.188 10 false *A 5.219,1.969 5.417,2.156 0.198,0.188 10 false *3 5.979,1.948 6.177,2.135 0.198,0.188 10 false *4 6.365,3.125 6.563,3.313 0.198,0.188 10 false *b 3.844,4.24 4.042,4.427 0.198,0.188 10 false *1 3.844,4.594 4.042,4.781 0.198,0.188 10 false *2

Text in Illustration
*A Models without TRC *B Models with TRC
*1 Hybrid Vehicle Control ECU *2 Skid Control ECU
*3

Engine and MG2

-

Motive Force Regulation



*4 Brake Actuator
*a Slippery Surface *b Brake the slipping drive wheel



f.

Vehicle Stability Control (VSC)

i.

The followings are two examples that can be considered as circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the motive force and the brakes at each wheel when the vehicle is under one of the conditions indicated below.

X100701E04
1.841,2.361 2.046,2.549 0.206,0.187 10 *a 4.46,2.361 4.656,2.524 0.196,0.162 10 *b

Text in Illustration
*a Front Wheel Skid Tendency *b Rear Wheel Skid Tendency


ii.

To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle's yaw rate and the vehicle's lateral acceleration, which are then calculated by the skid control ECU.


iii.

Whether or not the vehicle is in the state of front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the yaw rate (a target yaw rate that is determined by the vehicle speed and steering angle) that should be rightfully generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the locus of travel. Thus, the skid control ECU determines that there is a large tendency to front wheel skid.

X100702E08
3.656,0.26 3.906,0.5 0.25,0.24 10 false *a 4.542,0.781 4.792,1.021 0.25,0.24 10 false *b

Text in Illustration
*a Actual Locus of Travel (Actual Yaw Rate) *b Locus of Travel (Based on the Target Yaw Rate)


iv.

Whether the vehicle is in the state of the rear wheel skid or not is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle and the slip angular velocity are large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.

X100703E14
3.781,0.885 2.615,0.885 true 3.844,0.823 3.844,0.302 3.844,0.302 4.063,0.302 true 2.458,0.802 2.667,1.031 0.208,0.229 10 false *a 4.021,0.542 4.229,0.771 0.208,0.229 10 false *c 4.073,0.198 4.271,0.385 0.198,0.188 10 false *b

Text in Illustration
*a Direction of Travel of the Vehicle's Center of Gravity *b Slip Angle
*c Movement of Vehicle - -


v.

When the skid control ECU determines that the vehicle has a tendency to front wheel skid or rear wheel skid, it decreases the motive force and applies the brake of a front or rear wheel to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.


vi.

When the skid control ECU determines that there is a large front wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. The skid control ECU controls the motive force and applies the brakes of the front wheels and rear wheel of the inner circle of the turn in order to help restrain the front wheel skid tendency.

X101512E01
3.155,2.041 3.362,2.285 0.207,0.244 10 *a

Text in Illustration
*a Making a Right Turn - -
V100135

Brake Force
V100138

Control Moment


vii.

When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front and rear wheels of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured.

X101513E01
3.046,2.368 3.292,2.621 0.246,0.253 10 *a

Text in Illustration
*a Making a Right Turn - -
V100135

Brake Force
V100138

Control Moment



g.

Hill-start Assist Control

i.

When the vehicle starts off on a steep or slippery hill, the vehicle could descend backward while the driver switches from the brake pedal to the accelerator pedal, thus making it difficult for the vehicle to start off. To prevent this from occurring, the Hill-start Assist Control temporarily (approximately 2 seconds at the maximum) applies the brakes to all the wheels in order to prevent the vehicle from descending backward.


ii.

Without the Hill-start Assist Control, the driver must quickly and precisely switch from the brake pedal to the accelerator pedal. With the Hill-start Assist Control, however, the driver can start off easily and operate the pedal in a relaxed manner because the Hill-start Assist Control prevents the vehicle from descending backward.



h.

Motive Force Control during TRC or VSC Operation

i.

During the TRC or VSC operation, the skid control ECU outputs the motive force control signal to the hybrid vehicle control ECU. Upon receiving this signal, the hybrid vehicle control ECU inhibits the motive force.

X101709E18
4.625,0.115 6.802,0.406 2.177,0.292 10 false (A): Start of motive force control 4.625,0.521 6.208,0.844 1.583,0.323 10 false (B): Start of brake control 4.625,0.948 6.417,1.292 1.792,0.344 10 false (C): Brake control completed 4.625,1.375 7,1.708 2.375,0.333 10 false (D): Motive force control completed 0.271,1.448 2,1.854 1.729,0.406 10 false Level of Strong Front Wheel Skid or Rear Wheel Skid 2.24,1.938 2.51,2.135 0.271,0.198 10 false (A) 2.531,1.938 2.813,2.146 0.281,0.208 10 false (B) 4.573,1.938 4.813,2.146 0.24,0.208 10 false (C) 4.865,1.938 5.146,2.125 0.281,0.188 10 false (D) 0.448,2.688 1.615,2.927 1.167,0.24 10 false Vehicle Condition 0.229,4.344 1.552,4.573 1.323,0.229 10 false Motive Force Control 0.24,5.917 1.615,6.302 1.375,0.385 10 false Brake Wheel Cylinder Fluid Pressure* 5.688,3.573 6.094,3.771 0.406,0.198 10 false Time 5.688,5.167 6.083,5.396 0.396,0.229 10 false Time 5.688,6.729 6.063,6.938 0.375,0.208 10 false Time 0.104,7.438 5.302,7.813 5.198,0.375 10 false *: The wheel cylinder that activates varies depending on the condition of the vehicle




FUNCTION


a.

VSC OFF Switch

i.

The operation of the VSC and TRC functions can be stopped by the VSC OFF switch. While the vehicle is running off the shoulder of the road or running on the dirt road, the engine output control is stopped to maintain drive torque.


ii.

The VSC OFF switch can select the 3 modes (Normal Mode, TRC-OFF Mode, VSC-OFF Mode). When the VSC OFF switch is pressed briefly, TRC-OFF Mode is entered and the TRC function will be disabled. When the VSC OFF switch is pressed and held for 3 seconds or more, VSC-OFF Mode is entered and the TRC and VSC functions will be disabled.


iii.

After the power source is turned off in the TRC-OFF Mode or VSC-OFF Mode, turning the power source on again selects the Normal Mode. The system also enters Normal Mode automatically when the vehicle speed increases in TRC-OFF Mode.

X106029E10
3.167,0.771 4.625,1.052 1.458,0.281 10 false Normal Mode 2.104,2.042 3.563,2.323 1.458,0.281 10 false VSC-OFF Mode 0.604,2.969 5.323,3.25 4.719,0.281 10 false : VSC OFF Switch Operation (Briefly press) 0.604,3.333 5.323,3.615 4.719,0.281 10 false : VSC OFF Switch Operation (Press and hold for 3 seconds or more) 4.073,2.052 5.531,2.333 1.458,0.281 10 false TRC-OFF Mode


iv.

The operations of the brake control functions in each mode are as follows:

Mode Brake Control Function Combination Meter Assembly
TRC VSC Multi-information Display VSC OFF Indicator Light
Normal Mode Controllable Controllable - -
TRC-OFF Mode Not Controllable Controllable TRC OFF message is displayed -
VSC-OFF Mode Not Controllable Not Controllable* TRC OFF message is displayed Illuminates

HINT:

*: The control is effected during braking or while the yaw rate is large.





CONSTRUCTION


a.

Brake Actuator

i.

The brake actuator consists of the actuator portion and skid control ECU.


ii.

The brake actuator regulates the hydraulic brake pressure to each wheel cylinder.

X108149E03
2.375,0.823 2.073,0.365 2.073,0.365 1.896,0.365 true 3.688,0.948 4.073,0.313 4.073,0.313 4.24,0.313 true 2.229,2.938 1.875,3.333 1.875,3.333 1.708,3.333 true 4.604,2.938 5,3.333 5,3.333 5.177,3.333 true 1.729,0.281 1.906,0.448 0.177,0.167 10 false *1 1.552,3.25 1.729,3.417 0.177,0.167 10 false *3 5.198,3.24 5.375,3.406 0.177,0.167 10 false *4 4.26,0.219 4.438,0.385 0.177,0.167 10 false *2

Text in Illustration
*1 Skid Control ECU *2 Actuator Portion
*3 Hydraulic Brake Booster *4 Stroke Simulator
V100145

Brake Actuator - -


iii.

The construction of the brake actuator, and the role of each part, is as follows.

Component Function
Pressure Control Solenoid Valve Controls the wheel cylinder pressure to generate a braking force responsive to the braking force requirement when the brake pedal is depressed normally.
Switching Solenoid Valve Switches the brake hydraulic path when the brake control system is activated.
Control Solenoid Valve Controls the wheel cylinder pressure when the ABS with EBD, brake assist, TRC, VSC and Hill-start Assist Control are activated.
Master Cylinder Pressure Sensor The master cylinder pressure sensor converts the fluid pressure generated by the hydraulic brake booster into electrical signals and transmits them to the skid control ECU. Accordingly, the skid control ECU determines the braking force required by the driver.
Front Wheel Cylinder Pressure Sensor This sensor detects the fluid pressure that acts on the respective wheel cylinders and transmits them to the skid control ECU in the form of feedback. Accordingly, the skid control ECU monitors the fluid pressure of the wheel cylinders and controls the control solenoid valve, in order to achieve the optimal wheel cylinder pressures.
Accumulator Pressure Sensor The accumulator pressure sensor constantly detects the brake fluid pressure in the accumulator and transmits the signals to the skid control ECU. Accordingly, the skid control ECU controls the pump motor.

X104757E11
1.521,0.135 1.406,0.135 1.406,0.135 1.406,0.542 true 2.469,0.135 2.375,0.135 2.375,0.135 2.073,0.583 true 5.021,1.802 4.906,1.802 4.906,1.802 4.667,2.469 true 6.625,3.677 6.531,3.677 6.531,3.677 6.333,4.031 true 3.948,0.646 3.51,0.646 true 4.917,1.208 5.354,1.208 true 1.552,0.031 1.823,0.24 0.271,0.208 10 false *1 2.5,0.042 2.771,0.25 0.271,0.208 10 false *2 5.385,1.104 5.656,1.313 0.271,0.208 10 false *4 3.333,0.573 3.604,0.781 0.271,0.208 10 false *3 2.229,1.708 2.5,1.917 0.271,0.208 10 false *5 5.052,1.698 5.323,1.906 0.271,0.208 10 false *6 1.563,4.271 1.833,4.479 0.271,0.208 10 false *7 2.438,4.573 2.646,4.781 0.208,0.208 10 false *8 3.042,4.875 3.313,5.083 0.271,0.208 10 false *11 4.229,4.083 4.5,4.292 0.271,0.208 10 false *9 4.115,4.875 4.385,5.083 0.271,0.208 10 false *12 5.24,4.094 5.51,4.302 0.271,0.208 10 false *10 5.198,4.74 5.469,4.948 0.271,0.208 10 false *13 5.427,5.74 5.698,5.948 0.271,0.208 10 false *16 3.208,5.865 3.479,6.073 0.271,0.208 10 false *15 1,5.542 1.271,5.75 0.271,0.208 10 false *14 1.469,6.708 1.74,6.917 0.271,0.208 10 false *17 2.271,6.688 2.542,6.896 0.271,0.208 10 false *18 4.083,6.698 4.354,6.906 0.271,0.208 10 false *19 4.875,6.708 5.146,6.917 0.271,0.208 10 false *20 6.354,6.792 6.625,7 0.271,0.208 10 false *29 5.333,8.542 5.604,8.75 0.271,0.208 10 false *28 3.615,8.542 3.885,8.75 0.271,0.208 10 false *27 2.688,8.542 2.958,8.75 0.271,0.208 10 false *26 1.01,8.531 1.281,8.74 0.271,0.208 10 false *25 1.458,7.698 1.729,7.906 0.271,0.208 10 false *21 2.25,7.698 2.521,7.906 0.271,0.208 10 false *22 4.083,7.708 4.354,7.917 0.271,0.208 10 false *23 4.885,7.698 5.156,7.906 0.271,0.208 10 false *24 6.656,3.583 6.958,3.813 0.302,0.229 10 false *30

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Control Solenoid Valve *30 Brake Actuator



b.

Hydraulic Brake Booster

i.

The hydraulic brake booster consists of the operating rod which is directly connected to the brake pedal, power piston, master cylinder piston, regulator piston and the spool valve to switch the brake fluid passage.


ii.

The operating rod is directly connected to the power piston, by which the operating force of the brake pedal is transmitted.


iii.

The regulator piston is directly connected to the spool valve through which the master cylinder pressure is applied to the regulator piston in the advance direction (left direction in the illustration) and the pressure boosted by the brake booster is applied to the piston in the retard direction (right direction in the illustration), thus balancing the pressures in both directions. In addition, a return spring is placed in the regulator piston to ensure the return force of the spool valve when no pressure is applied.

X108150E03
3.563,1.135 4.135,0.521 4.135,0.521 4.24,0.521 true 2.375,3.25 2.688,3.698 2.688,3.698 2.771,3.698 true 4.604,3.125 4.979,3.594 4.979,3.594 5.063,3.594 true 2.167,4.521 2.073,4.521 2.073,4.521 1.865,5.406 true 2.802,4.51 2.708,4.51 2.708,4.51 2.51,5.344 true 4.104,4.51 4.01,4.51 4.01,4.51 3.813,5.354 true 4.802,4.51 4.708,4.51 4.708,4.51 4.49,5.396 true 5.823,4.51 5.74,4.51 5.74,4.51 5.521,5.406 true 2.49,6.292 2.396,6.292 2.396,6.292 2.229,5.604 true 3.542,6.292 3.458,6.292 3.458,6.292 3.292,5.625 true 4.26,0.427 4.49,0.667 0.229,0.24 10 false *1 5.094,3.51 5.323,3.75 0.229,0.24 10 false *3 2.792,3.615 3.021,3.854 0.229,0.24 10 false *2 0.354,4.396 0.615,4.615 0.26,0.219 10 false *a 2.188,4.438 2.417,4.677 0.229,0.24 10 false *4 2.823,4.427 3.052,4.667 0.229,0.24 10 false *5 4.125,4.417 4.354,4.656 0.229,0.24 10 false *6 4.833,4.417 5.063,4.656 0.229,0.24 10 false *7 5.854,4.417 6.083,4.656 0.229,0.24 10 false *8 2.51,6.208 2.74,6.375 0.229,0.167 10 false *9 3.563,6.208 3.792,6.385 0.229,0.177 10 false *9

Text in Illustration
*1 Brake Actuator *2 Hydraulic Brake Booster
*3 Stroke Simulator *4 Spool Valve
*5 Regulator Piston *6 Master Cylinder Piston
*7 Power Piston *8 Operating Rod
*9 Return Spring - -
*a Hydraulic Brake Booster Cross Section - -

X104759E11
2.354,1.5 2.531,0.417 2.531,0.417 2.615,0.417 true 4.302,1.583 4.5,0.417 4.5,0.417 4.573,0.417 true 5.073,1.594 5.26,0.427 5.26,0.427 5.344,0.427 true 6.031,1.813 6.26,0.417 6.26,0.417 6.344,0.417 true 1.563,1.875 1.75,3.271 1.75,3.271 1.802,3.271 true 2.313,1.969 2.313,3.271 2.313,3.271 2.427,3.271 true 3.167,1.969 3.344,3.271 3.344,3.271 3.396,3.271 true 5.177,2.156 5.365,3.271 5.365,3.271 5.417,3.271 true 0.073,0.063 0.385,0.323 0.313,0.26 10 false *a 1.25,0.333 1.448,0.521 0.198,0.188 10 false *b 1.656,0.344 1.854,0.531 0.198,0.188 10 false *c 3.927,0.333 4.125,0.521 0.198,0.188 10 false *b 2.719,3.156 2.917,3.344 0.198,0.188 10 false *d 4.219,3.156 4.417,3.344 0.198,0.188 10 false *e 2.646,0.281 2.823,0.458 0.177,0.177 10 false *1 4.615,0.281 4.792,0.458 0.177,0.177 10 false *2 5.438,0.281 5.615,0.458 0.177,0.177 10 false *3 6.417,0.281 6.594,0.458 0.177,0.177 10 false *4 1.823,3.177 2,3.354 0.177,0.177 10 false *5 2.448,3.177 2.625,3.354 0.177,0.177 10 false *6 3.417,3.177 3.594,3.354 0.177,0.177 10 false *7 5.438,3.177 5.615,3.354 0.177,0.177 10 false *8

Text in Illustration
*1 Regulator Piston *2 Master Cylinder Piston
*3 Power Piston *4 Operating Rod
*5 Spool Valve *6 Regulator Chamber
*7 Master Cylinder Chamber *8 Booster Chamber
*a Simplified Diagram *b To Reservoir Tank
*c From Accumulator *d To Front Brake
*e To Rear Brake - -



c.

Stroke Simulator

i.

The stroke simulator is positioned beside the hydraulic brake booster. It generates a pedal stroke in accordance with the driver's pedal effort during braking. Containing 2 types of coil springs with different spring constants, the stroke simulator provides pedal stroke characteristics in relation to the master cylinder pressure.


ii.

To shut off the flow of fluid from the master cylinder when the system fails, a two-position solenoid valve has been provided.

X108151E02
3.531,0.833 4.198,0.323 4.198,0.323 4.406,0.323 true 2.302,2.875 2.677,3.479 2.677,3.479 2.875,3.479 true 4.594,2.844 5,3.427 5,3.427 5.219,3.427 true 2.833,4.708 3.104,4.083 3.104,4.083 3.219,4.083 true 3.302,4.906 3.573,4.083 3.573,4.083 3.688,4.083 true 3.948,5.042 4.219,4.083 4.219,4.083 4.333,4.083 true 4.427,0.229 4.635,0.417 0.208,0.188 10 false *1 3.25,4 3.427,4.167 0.177,0.167 10 false *4 3.083,6.031 3.26,6.198 0.177,0.167 10 false *b 0.865,3.896 1.042,4.063 0.177,0.167 10 false *a 4.75,6 4.927,6.167 0.177,0.167 10 false *c 3.708,3.99 3.885,4.156 0.177,0.167 10 false *4 4.375,3.99 4.552,4.156 0.177,0.167 10 false *5 2.896,3.385 3.073,3.552 0.177,0.167 10 false *2 5.24,3.344 5.417,3.51 0.177,0.167 10 false *3

Text in Illustration
*1 Brake Actuator *2 Hydraulic Brake Booster
*3 Stroke Simulator *4 Coil Spring
*5 Piston - -
*a Stroke Simulator Cross Section *b To Reservoir Tank
*c From Hydraulic Brake Booster - -



d.

Brake Booster Pump Assembly

i.

The brake booster pump assembly consists of pump, pump motor and accumulator.


ii.

A plunger type pump is used. This pump is operated by rotation of the camshaft driven by the motor, and then supplies high-pressurized fluid to the accumulator.


iii.

The high-pressurized nitrogen gas is charged and sealed in the accumulator. The accumulator has been made more compact by using a metallic bellow-formed tube.

X108160E04
1.844,4.073 1.969,4.073 1.969,4.073 2.469,4.531 true 1.833,4.927 1.938,4.927 1.938,4.927 2.958,5.635 true 1.833,5.729 1.927,5.729 1.927,5.729 2.344,6.021 true 5.375,3.833 5.26,3.833 5.26,3.833 4.823,4.24 true 5.396,4.573 4.667,4.573 true 5.375,5.469 5.26,5.469 5.26,5.469 4.76,5.26 true 2.635,2.708 2.74,2.708 2.74,2.708 3.031,2.115 true 4.198,1.354 4.438,0.74 4.438,0.74 4.521,0.74 true 4.552,0.646 4.792,0.865 0.24,0.219 10 false *1 2.479,2.615 2.708,2.823 0.229,0.208 10 false *2 0.813,3.438 1.115,3.688 0.302,0.25 10 false *a 1.656,3.99 1.875,4.219 0.219,0.229 10 false *2 1.677,4.844 1.885,5.052 0.208,0.208 10 false *3 1.677,5.646 1.885,5.875 0.208,0.229 10 false *4 5.396,3.75 5.625,3.958 0.229,0.208 10 false *1 5.396,4.49 5.604,4.688 0.208,0.198 10 false *5 5.396,5.385 5.625,5.604 0.229,0.219 10 false *6

Text in Illustration
*1 Accumulator *2 Pump Motor
*3 Camshaft *4 Pump
*5 Nitrogen Gas *6 Bellows-formed
*a Cross Section - -



e.

Brake Pedal Stroke Sensor Assembly

i.

A non-contact type brake pedal stroke sensor assembly is used.


ii.

This sensor detects the extent of the brake pedal stroke and transmits it to the skid control ECU.

X135652E01
1.417,0.344 1.615,0.344 1.615,0.344 2.813,1.385 true 4.677,0.625 4.781,0.625 4.781,0.625 5.052,1.229 true 5.25,0.979 5.563,0.406 5.563,0.406 5.708,0.406 true 4.583,2.292 4.688,2.292 4.688,2.292 4.854,2.01 true 4.385,3.656 4.885,4.083 4.885,4.083 5.031,4.083 true 4.375,4.969 4.917,4.594 4.917,4.594 5.063,4.594 true 0.156,0.25 1.385,0.698 1.229,0.448 10 false Brake Pedal Stroke Sensor Assembly 3,1.063 3.156,1.26 0.156,0.198 10 false A 2.625,2.135 2.781,2.333 0.156,0.198 10 true A 5.729,0.302 6.708,0.5 0.979,0.198 10 false Return Spring 3.813,0.531 4.656,0.74 0.844,0.208 10 false Sensor Shaft 4.198,2.188 4.573,2.406 0.375,0.219 10 false Lever 5.042,2.635 6.219,2.844 1.177,0.208 10 false A-A Cross Section 1.146,3.125 2.177,3.354 1.031,0.229 10 false Output Voltage 2.052,3.406 2.406,3.583 0.354,0.177 10 false 4.6V 2.188,4.781 2.406,4.948 0.219,0.167 10 false 1V 2.083,5 2.417,5.188 0.333,0.188 10 false 0.4V 2.198,5.198 2.417,5.365 0.219,0.167 10 false 0V 2.51,5.292 2.896,5.49 0.385,0.198 10 false -9.7° 2.958,5.281 3.115,5.479 0.156,0.198 10 false 0 4.427,5.271 4.792,5.458 0.365,0.188 10 false 58.3° 5.083,3.99 5.698,4.188 0.615,0.198 10 false SKS1 5.094,4.521 5.708,4.719 0.615,0.198 10 false SKS2 4.771,5.448 6.854,5.688 2.083,0.24 10 false Sensor Lever Rotational Angle

HINT:
·

To install a brake pedal stroke sensor assembly, which is available as a service part, perform as follows:

-

The sensor lever is secured with a pin to "0" stroke (Do not detach the pin until the installation has been completed.).

-

In this state, install the sensor on the brake pedal (in the OFF state) on the vehicle.

-

After completing the installation, firmly press the brake pedal once to break off the pin that is securing the sensor in place.

-

Make sure the broken pin does not remain in the sensor lever.



·

After replacing the brake pedal stroke sensor assembly, initialization of brake pedal stroke sensor assembly must be required on the skid control ECU side. For Details, refer to the Repair Manual.





f.

Speed Sensor

i.

An active type speed sensor is used. This sensor contains a Hall IC.


ii.

The sensor rotor, which consists of N and S poles that are arranged in a circle, is integrated with the hub bearing inner race.


iii.

An active type speed sensor uses a Hall IC to detect magnetic field changes caused when the sensor rotor rotates, and the sensor outputs the detected information to the skid control ECU as digital pulses.


iv.

To detect the vehicle speed, the frequency of the output pulses is used. Because the active type sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.

X100718E17
5.667,3.188 5.229,3.188 true 4.333,6.896 4.823,6.552 4.823,6.552 4.958,6.552 false 1.635,5.625 2.573,5.99 0.938,0.365 10 false Vehicle Speed 1.625,6.76 2.563,7.125 0.938,0.365 10 false Sensor Output 3.521,7.271 3.865,7.625 0.344,0.354 10 false Time 5,6.458 6.031,6.781 1.031,0.323 10 false Digital Pulses 3.99,1.219 4.479,1.438 0.49,0.219 10 false Hall IC 2.042,2.094 2.938,2.302 0.896,0.208 10 false Sensor Rotor 5.698,3.094 6.844,3.448 1.146,0.354 10 false Speed Sensor 1.604,4.438 3.385,4.667 1.781,0.229 10 false N and S Poles Arrangement



g.

Yaw Rate and Acceleration Sensor

i.

The yaw rate and acceleration sensor is built into the airbag sensor assembly.


ii.

The yaw rate sensor detects acceleration in the horizontal forward-backward and left-right directions using the signals from 2 acceleration sensors, and transmits signals to the skid control ECU.

X108153E04
1.156,1.792 0.729,2.24 0.729,2.24 0.531,2.24 true 0.365,2.146 0.573,2.354 0.208,0.208 10 false *1 6.646,1.333 6.854,1.542 0.208,0.208 10 false *b 5.083,0.073 5.292,0.281 0.208,0.208 10 false *a

Text in Illustration
*1

Airbag Sensor Assembly

-

Yaw Rate and Acceleration Sensor



- -
*a Left-right Direction *b Forward-backward Direction
V100135

Front - -

HINT:

After replacing the airbag sensor assembly, or the skid control ECU, initialization of the yaw rate sensor is required. For the actual procedure, refer to the Repair Manual.




h.

Steering Angle Sensor

i.

The steering angle sensor detects the steering direction and angle, and sends this signal to the skid control ECU.


ii.

The steering angle sensor contains two sets of magnetic reluctance elements that detect the rotational movement of a magnet that is built into the detection gear. Thus, the sensor detects the changes that occur in the magnetic reluctance elements along with the rotational movement of the detection gear, in order to detect the rotational movement of the steering wheel.

X104966E03
3.99,1.958 4.76,1.958 true 3.74,2.125 3.74,2.531 3.74,2.531 4.75,2.531 true 1.76,1.969 2.531,1.969 true 1.604,1.875 1.823,2.083 0.219,0.208 10 false *1 4.781,1.865 5,2.073 0.219,0.208 10 false *2 4.781,2.438 5,2.646 0.219,0.208 10 false *2

Text in Illustration
*1 Steering Angle Sensor *2 Detection Gear

NOTICE:

Do not remove the steering angle sensor from the spiral cable with sensor sub-assembly. If there is a malfunction in the steering angle sensor, replace the spiral cable with sensor sub-assembly.





OPERATION


a.

Hydraulic Brake Booster

i.

When the brake pedal is depressed by the driver, the operating force of the brake pedal is transmitted from the operating rod via the power piston to the master cylinder piston. The return spring of the master cylinder chamber has a higher setting load than that of the regulator piston, thus allowing the regulator piston to move forward before the master cylinder chamber is compressed.


ii.

The spool valve closes the oil passage to the reservoir tank and the booster chamber and opens the one from the accumulator and the booster chamber, and this allows the fluid pressure to be applied to the booster chamber, generating a boosted force and further boosting the brake pedal force. When the fluid pressure is applied to the booster chamber, the boosted force overcomes the return spring force, compressing the master cylinder and increasing the fluid pressure. In addition, the fluid pressure in the booster chamber increases the fluid pressure in the rear brake oil passage.

X104763E10
2.448,1.49 2.573,0.667 2.573,0.667 2.646,0.667 true 3.146,1.552 3.292,0.656 3.292,0.656 3.365,0.656 true 4.271,1.573 4.5,0.656 4.5,0.656 4.573,0.656 true 5.229,1.615 5.469,0.667 5.469,0.667 5.542,0.667 true 6.125,1.781 6.385,0.667 6.385,0.667 6.469,0.667 true 5.563,3.26 5.438,3.26 5.438,3.26 5.135,1.823 true 1.969,3.26 1.854,3.26 1.854,3.26 1.552,1.823 true 1.688,0.635 1.906,0.844 0.219,0.208 10 false *a 2.677,0.573 2.896,0.781 0.219,0.208 10 false *1 3.385,0.563 3.604,0.771 0.219,0.208 10 false *2 4.594,0.573 4.813,0.781 0.219,0.208 10 false *3 5.563,0.573 5.781,0.781 0.219,0.208 10 false *4 6.49,0.573 6.708,0.781 0.219,0.208 10 false *5 2.74,3.167 2.958,3.375 0.219,0.208 10 false *b 4.25,3.167 4.469,3.375 0.219,0.208 10 false *c 1.99,3.177 2.208,3.385 0.219,0.208 10 false *6 5.583,3.177 5.802,3.385 0.219,0.208 10 false *7

Text in Illustration
*1 Regulator Piston *2 Return Spring
*3 Master Cylinder Piston *4 Booster Chamber
*5 Operating Rod *6 Spool Valve
*7 Power Piston - -
*a From Accumulator *b To Front Brake
*c To Rear Brake - -


iii.

When the driver's pedal operation is stopped and the pedal operating force and the master cylinder pressure are balanced, the forces are respectively applied to the front and rear of the regulator piston, in other words, the forces respectively generated by the master cylinder pressure and the regulator pressure are balanced, therefore, the spool valve closes the passage between the booster chamber and the accumulator, and also to the reservoir tank.

X104764E09
1.865,1.74 2.094,0.625 2.094,0.625 2.188,0.625 true 2.667,1.656 2.917,0.615 2.917,0.615 3.01,0.615 true 2.115,1.833 2.115,3.042 2.115,3.042 2.229,3.042 true 2.927,1.823 2.927,3.031 2.927,3.031 3.042,3.031 true 2.219,0.521 2.438,0.719 0.219,0.198 10 false *1 3.042,0.521 3.26,0.719 0.219,0.198 10 false *2 2.25,2.938 2.469,3.135 0.219,0.198 10 false *a 3.063,2.927 3.281,3.125 0.219,0.198 10 false *b

Text in Illustration
*1 Spool Valve *2 Regulator Piston
*a Regulator Pressure *b Master Cylinder Pressure


iv.

When the driver's pedal operating force is reduced, the master cylinder pressure drops, therefore, the force applied to the regulator piston return side becomes larger relatively and the regulator piston and the spool valve move further rearward, and this opens the fluid passage between the reservoir tank and the booster chamber.


v.

As a result, the brake fluid in the hydraulic brake booster is returned to the reservoir tank, decreasing the booster chamber pressure and balancing the booster chamber pressure against the reduced master cylinder pressure. This repetitive operation decreases the booster chamber pressure and the master cylinder pressure in accordance with the pedal operating force.

X104765E10
2.385,0.635 2.229,0.635 2.229,0.635 1.875,1.802 true 3.208,0.635 3.052,0.635 3.052,0.635 2.75,1.615 true 5.656,0.646 5.5,0.646 5.5,0.646 5.198,1.635 true 1.24,0.333 1.448,0.552 0.208,0.219 10 false *a 2.406,0.542 2.625,0.76 0.219,0.219 10 false *1 3.229,0.542 3.448,0.76 0.219,0.219 10 false *2 5.677,0.552 5.896,0.771 0.219,0.219 10 false *3 2.76,3.167 2.969,3.375 0.208,0.208 10 false *b 4.208,3.167 4.417,3.375 0.208,0.208 10 false *c

Text in Illustration
*1 Spool Valve *2 Regulator Piston
*3 Booster Chamber - -
*a To Reservoir Tank *b From Front Brake
*c From Rear Brake - -



b.

Brake Booster Pump Assembly

i.

The brake fluid that is discharged by the pump passes through the check valve and is stored in the accumulator. The hydraulic pressure that is stored in the accumulator is used for providing the hydraulic pressure that is needed for normal braking and for operating the brake control.


ii.

The pump motor is activated upon receipt of signals from the skid control ECU to turn on the motor relays built into the skid control ECU.


iii.

The accumulator pressure sensor constantly monitors the pressure in the accumulator and transmits it to the skid control ECU. If the accumulator pressure drops below the set pressure, the skid control ECU sends an activation signal to the motor relay in order to actuate the pump motor until the pressure in the accumulator reaches the set pressure.

X124754E03
2.646,0.385 2.542,0.385 2.542,0.385 2.302,0.99 true 4,0.875 3.896,0.875 3.896,0.875 3.656,1.479 true 4.844,1.74 4.75,1.74 4.75,1.74 3.802,2.438 true 1.188,2.031 1.969,2.24 0.781,0.208 10 false Relief Valve 2,2.938 3.927,3.135 1.927,0.198 10 false Accumulator Pressure Sensor 1.615,3.677 2.792,3.885 1.177,0.208 10 false Skid Control ECU 4.146,3.802 4.958,4.01 0.813,0.208 10 false Motor Relay 4.604,3.177 5.188,3.406 0.583,0.229 10 false Operate 4.896,2.698 6.406,2.958 1.51,0.26 10 false Pump and Pump Motor 2.677,0.302 3.698,0.5 1.021,0.198 10 false Reservoir Tank 4.885,1.656 5.729,1.854 0.844,0.198 10 false Check Valve 4.031,0.792 4.958,0.979 0.927,0.188 10 false Accumulator


iv.

If the pump and the pump motor continue to operate unintentionally, and the accumulator pressure sensor fails, a high pressure would be created in the accumulator. At this time, the relief valve will open and return the brake fluid to the reservoir tank, to reduce the accumulator pressure.

X124755E03
2.635,0.417 2.542,0.417 2.542,0.417 2.302,1.021 true 3.99,0.906 3.896,0.906 3.896,0.906 3.656,1.5 true 4.854,1.729 4.75,1.729 4.75,1.729 3.792,2.458 true 0.25,2.063 1.938,2.271 1.688,0.208 10 false Relief Valve Close → Open 2,2.938 3.917,3.177 1.917,0.24 10 false Accumulator Pressure Sensor 1.604,3.688 2.792,3.885 1.188,0.198 10 false Skid Control ECU 4.167,3.823 4.969,4.042 0.802,0.219 10 false Motor Relay 4.594,3.281 6.021,3.5 1.427,0.219 10 false Operate Continuously 4.917,2.729 6.427,2.927 1.51,0.198 10 false Pump and Pump Motor 2.677,0.333 3.719,0.542 1.042,0.208 10 false Reservoir Tank 4.896,1.646 5.771,1.833 0.875,0.188 10 false Check Valve 4.031,0.823 4.927,1.031 0.896,0.208 10 false Accumulator


v.

If the accumulator pressure drops abnormally to a level below the pressure set at the ECU, the skid control ECU illuminates the brake warning light/red (malfunction), the brake warning light/yellow (minor malfunction), ABS warning light and the master warning light. Then, the buzzer in the combination meter assembly sounds to alert the driver of the abnormal hydraulic pressure.

X124756E03
1.688,0.167 1.781,0.167 1.781,0.167 2.021,0.771 true 4.865,1.333 4.75,1.333 4.75,1.333 3.813,2.042 true 2.563,4.323 2.563,3.531 false 3.25,3.729 5.792,3.958 2.542,0.229 10 false - Brake Warning Light/Red (Malfunction) 2.01,2.552 3.99,2.833 1.979,0.281 10 false Accumulator Pressure Sensor 1.26,3.281 2.063,3.688 0.802,0.406 10 false Skid Control ECU 3.854,3.271 5.719,3.531 1.865,0.26 10 false Combination Meter Assembly 4.938,2.344 6.844,2.563 1.906,0.219 10 false Pump and Pump Motor 0.708,0.073 1.677,0.271 0.969,0.198 10 false Reservoir Tank 4.917,1.25 5.771,1.458 0.854,0.208 10 false Check Valve 2.5,1.271 3.333,1.479 0.833,0.208 10 false Accumulator 3.25,4.885 3.927,5.104 0.677,0.219 10 false - Buzzer 3.25,4.594 4.583,4.823 1.333,0.229 10 false - Slip Indicator Light 3.25,4.292 4.667,4.521 1.417,0.229 10 false - ABS Warning Light 3.25,3.99 6.292,4.219 3.042,0.229 10 false - Brake Warning Light/Yellow (Minor Malfunction) 2.177,4.333 3.073,4.625 0.896,0.292 10 false CAN (V Bus)



c.

Normal Brake Operation (with Regenerative Brake Cooperative Control)

i.

During normal braking, the switching solenoid valves SSC and SCC open and the switching solenoid valves SMC and SRC close, and thus the fluid pressure circuit from the hydraulic brake booster to each wheel cylinder is individually separated. Each of the wheel cylinder pressures can be increased, retained and decreased by controlling the pressure control solenoid valves SLA and SLR under the condition.


ii.

The skid control ECU calculates the braking force required by the driver in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor assembly. Then, the skid control ECU calculates the regenerative brake force value out of the required brake force and transmits the calculated value to the hybrid vehicle control ECU. Upon receiving the value, the hybrid vehicle control ECU generates a regenerative brake force. At the same time, the hybrid vehicle control ECU transmits the actual regenerative brake force value to the skid control ECU. The skid control ECU controls the solenoid valves in order to cause the hydraulic brake system to generate a brake force value (which is obtained by subtracting the regenerative brake force from the brake force value required by the driver).

X124757E03
0.135,0.844 1.917,1.104 1.781,0.26 10 false Stop Light Switch Assembly 0.146,2.135 1.865,2.5 1.719,0.365 10 false Brake Pedal Stroke Sensor Assembly 0.146,3.719 1.479,4.094 1.333,0.375 10 false Brake Booster Pump Assembly 3.042,1.177 3.625,1.75 0.583,0.573 10 false Solenoid Relay 2.615,0.125 5.5,0.375 2.885,0.25 10 false Brake Booster with Master Cylinder Assembly 2.813,0.698 3.938,0.906 1.125,0.208 10 false Skid Control ECU 2.958,3.833 3.771,4.052 0.813,0.219 10 false Motor Relay 4.646,0.49 5.698,0.708 1.052,0.219 10 false Brake Actuator 4.823,0.958 6.469,1.333 1.646,0.375 10 false Pressure Control Solenoid Valve (2) 4.823,1.781 6.667,1.99 1.844,0.208 10 false Switching Solenoid Valve (4) 4.823,2.365 6.573,2.583 1.75,0.219 10 false Regulator Pressure Sensor 4.823,2.906 6.385,3.281 1.563,0.375 10 false Wheel Cylinder Pressure Sensor 4.979,3.854 6.771,4.219 1.792,0.365 10 false Hybrid Vehicle Control ECU 5.302,4.469 6.75,4.708 1.448,0.24 10 false Regenerative Braking 4.25,4.115 4.781,4.5 0.531,0.385 10 false CAN (V Bus)


iii.

The skid control ECU calculates the target wheel cylinder pressure (equivalent to the brake force required by the driver) in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor assembly. The skid control ECU compares the wheel cylinder pressure with the target wheel cylinder pressure. If the wheel cylinder pressure is lower than the target wheel cylinder pressure, the skid control ECU boosts the pressure in the brake actuator. Accordingly, the fluid pressure in the accumulator is fed into the wheel cylinder. Moreover, this operation is the same when the hydraulic brake force must be increased in order to effect cooperative control in accordance with the changes in the regenerative brake force.

X104744E09
1.302,0.125 1.479,0.125 1.479,0.125 1.479,0.531 true 2.469,0.146 2.375,0.146 2.375,0.146 2.073,0.583 true 5.052,1.844 4.938,1.844 4.938,1.844 4.698,2.521 true 1.177,5.698 1.177,5.323 1.177,5.323 1.604,5.323 true 1.146,0.042 1.354,0.25 0.208,0.208 10 false *1 2.51,0.042 2.781,0.25 0.271,0.208 10 false *2 5.094,1.104 5.365,1.313 0.271,0.208 10 false *4 3.625,0.76 3.854,0.938 0.229,0.177 10 false *3 2.26,1.708 2.531,1.917 0.271,0.208 10 false *5 5.083,1.75 5.354,1.958 0.271,0.208 10 false *6 1.677,4.25 1.875,4.417 0.198,0.167 10 false *7 2.469,4.573 2.677,4.781 0.208,0.208 10 false *8 3.073,4.927 3.344,5.135 0.271,0.208 10 false *11 4.26,4.094 4.531,4.302 0.271,0.208 10 false *9 4.125,4.927 4.396,5.135 0.271,0.208 10 false *12 5.281,4.083 5.552,4.292 0.271,0.208 10 false *10 5.188,4.792 5.458,5 0.271,0.208 10 false *13 5.458,5.844 5.729,6.052 0.271,0.208 10 false *16 3.24,5.969 3.51,6.177 0.271,0.208 10 false *15 1.615,5.229 1.885,5.438 0.271,0.208 10 false *14 1.479,6.813 1.75,7.021 0.271,0.208 10 false *17 2.292,6.813 2.563,7.021 0.271,0.208 10 false *18 4.135,6.813 4.406,7.021 0.271,0.208 10 false *19 4.938,6.813 5.208,7.021 0.271,0.208 10 false *20 5.396,8.625 5.667,8.833 0.271,0.208 10 false *28 3.667,8.625 3.938,8.833 0.271,0.208 10 false *27 2.74,8.625 3.01,8.833 0.271,0.208 10 false *26 1.042,8.625 1.313,8.833 0.271,0.208 10 false *25 1.469,7.802 1.74,8.01 0.271,0.208 10 false *21 2.271,7.802 2.542,8.01 0.271,0.208 10 false *22 4.104,7.802 4.375,8.01 0.271,0.208 10 false *23 4.927,7.802 5.198,8.01 0.271,0.208 10 false *24 6.177,4.021 6.521,4.24 0.344,0.219 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item Normal Braking Increase Mode
Pressure Control Solenoid Valve SLA On*
SLR Off (Close)
Switching Solenoid Valve SSC On (Open)
SCC On (Open)
SMC On (Close)
SRC On (Close)
Pressure Holding Solenoid Valve FLH Off (Open)
FRH Off (Open)
RLH Off (Open)
RRH Off (Open)
Pressure Reduction Solenoid Valve FLR Off (Close)
FRR Off (Close)
RLR Off (Close)
RRR Off (Close)

HINT:

*: The solenoid valve constantly regulates the amount of opening of the valve in accordance with the use conditions in order to control the fluid pressure.



iv.

The skid control ECU calculates the target wheel cylinder pressure (equivalent to the brake force required by the driver) in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor assembly. The skid control ECU compares the wheel cylinder pressure with the target wheel cylinder pressure. If they are equal, the skid control ECU controls the brake actuator in the hold state. Accordingly, the wheel cylinder will be held at a constant pressure.

X104745E10
1.302,0.177 1.479,0.177 1.479,0.177 1.479,0.583 true 2.469,0.135 2.375,0.135 2.375,0.135 2.073,0.573 true 5.052,1.781 4.938,1.781 4.938,1.781 4.698,2.448 true 1.177,5.604 1.177,5.229 1.177,5.229 1.604,5.229 true 1.125,0.083 1.396,0.292 0.271,0.208 10 false *1 2.49,0.042 2.76,0.25 0.271,0.208 10 false *2 5.115,1.073 5.385,1.281 0.271,0.208 10 false *4 3.625,0.698 3.896,0.906 0.271,0.208 10 false *3 2.271,1.677 2.542,1.885 0.271,0.208 10 false *5 5.094,1.677 5.365,1.885 0.271,0.208 10 false *6 1.698,4.219 1.969,4.427 0.271,0.208 10 false *7 2.469,4.521 2.677,4.729 0.208,0.208 10 false *8 3.073,4.833 3.344,5.042 0.271,0.208 10 false *11 4.26,4.177 4.531,4.385 0.271,0.208 10 false *9 4.146,4.833 4.417,5.042 0.271,0.208 10 false *12 5.271,4.177 5.542,4.385 0.271,0.208 10 false *10 5.229,4.698 5.5,4.906 0.271,0.208 10 false *13 5.458,5.76 5.729,5.969 0.271,0.208 10 false *16 3.24,5.896 3.51,6.104 0.271,0.208 10 false *15 1.635,5.135 1.906,5.344 0.271,0.208 10 false *14 1.479,6.729 1.75,6.938 0.271,0.208 10 false *17 2.292,6.729 2.563,6.938 0.271,0.208 10 false *18 4.135,6.729 4.406,6.938 0.271,0.208 10 false *19 4.938,6.729 5.208,6.938 0.271,0.208 10 false *20 5.375,8.531 5.646,8.74 0.271,0.208 10 false *28 3.667,8.531 3.938,8.74 0.271,0.208 10 false *27 2.74,8.531 3.01,8.74 0.271,0.208 10 false *26 1.052,8.521 1.323,8.729 0.271,0.208 10 false *25 1.469,7.729 1.74,7.938 0.271,0.208 10 false *21 2.271,7.719 2.542,7.927 0.271,0.208 10 false *22 4.104,7.729 4.375,7.938 0.271,0.208 10 false *23 4.927,7.729 5.198,7.938 0.271,0.208 10 false *24 6.198,3.969 6.698,4.385 0.5,0.417 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item Normal Braking Holding Mode
Pressure Control Solenoid Valve SLA Off (Close)
SLR Off (Close)
Switching Solenoid Valve SSC On (Open)
SCC On (Open)
SMC On (Close)
SRC On (Close)
Pressure Holding Solenoid Valve FLH Off (Open)
FRH Off (Open)
RLH Off (Open)
RRH Off (Open)
Pressure Reduction Solenoid Valve FLR Off (Close)
FRR Off (Close)
RLR Off (Close)
RRR Off (Close)


v.

The skid control ECU calculates the target wheel cylinder pressure (equivalent to the brake force required by the driver) in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor assembly. The skid control ECU compares the wheel cylinder pressure with the target wheel cylinder pressure. If the wheel cylinder pressure is higher than the target wheel cylinder pressure, the skid control ECU reduces the pressure in the brake actuator. Accordingly, the pressure in the wheel cylinder decreases. Moreover, this operation is the same when the hydraulic brake force must be decreased in order to effect cooperative control in accordance with the changes in the regenerative brake force.

X104746E10
1.302,0.156 1.479,0.156 1.479,0.156 1.479,0.563 true 2.469,0.167 2.375,0.167 2.375,0.167 2.073,0.604 true 5.052,1.854 4.938,1.854 4.938,1.854 4.698,2.521 true 1.208,5.688 1.208,5.313 1.208,5.313 1.625,5.313 true 1.115,0.073 1.333,0.26 0.219,0.188 10 false *1 2.5,0.073 2.771,0.281 0.271,0.208 10 false *2 5.125,1.094 5.396,1.302 0.271,0.208 10 false *4 3.646,0.708 3.917,0.917 0.271,0.208 10 false *3 2.292,1.708 2.563,1.917 0.271,0.208 10 false *5 5.083,1.75 5.354,1.958 0.271,0.208 10 false *6 1.719,4.313 1.99,4.521 0.271,0.208 10 false *7 2.531,4.625 2.74,4.833 0.208,0.208 10 false *8 3.094,4.969 3.365,5.177 0.271,0.208 10 false *11 4.292,4.281 4.563,4.49 0.271,0.208 10 false *9 4.125,4.979 4.396,5.188 0.271,0.208 10 false *12 5.313,4.281 5.583,4.49 0.271,0.208 10 false *10 5.208,4.813 5.479,5.021 0.271,0.208 10 false *13 5.458,5.844 5.729,6.052 0.271,0.208 10 false *16 3.24,5.979 3.51,6.188 0.271,0.208 10 false *15 1.646,5.229 1.917,5.438 0.271,0.208 10 false *14 1.521,6.802 1.792,7.01 0.271,0.208 10 false *17 2.333,6.802 2.604,7.01 0.271,0.208 10 false *18 4.177,6.802 4.448,7.01 0.271,0.208 10 false *19 4.979,6.802 5.25,7.01 0.271,0.208 10 false *20 5.406,8.615 5.677,8.823 0.271,0.208 10 false *28 3.688,8.615 3.958,8.823 0.271,0.208 10 false *27 2.76,8.615 3.031,8.823 0.271,0.208 10 false *26 1.073,8.615 1.344,8.823 0.271,0.208 10 false *25 1.51,7.802 1.781,8.01 0.271,0.208 10 false *21 2.313,7.802 2.583,8.01 0.271,0.208 10 false *22 4.156,7.802 4.427,8.01 0.271,0.208 10 false *23 4.969,7.802 5.24,8.01 0.271,0.208 10 false *24 6.146,4.063 6.646,4.479 0.5,0.417 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item Normal Braking Reduction Mode
Pressure Control Solenoid Valve SLA Off (Close)
SLR On*
Switching Solenoid Valve SSC On (Open)
SCC On (Open)
SMC On (Close)
SRC On (Close)
Pressure Holding Solenoid Valve FLH Off (Open)
FRH Off (Open)
RLH Off (Open)
RRH Off (Open)
Pressure Reduction Solenoid Valve FLR Off (Close)
FRR Off (Close)
RLR Off (Close)
RRR Off (Close)

HINT:

*: The solenoid valve constantly regulates the amount of opening of the valve in accordance with the use conditions in order to control the fluid pressure.




d.

ABS with EBD

i.

Based on the signals received from the 4 speed sensors, the skid control ECU calculates each wheel speed and deceleration, and checks wheel slipping conditions. According to the slipping condition, the skid control ECU controls the pressure holding valve and pressure reduction valve in order to adjust the fluid pressure of the each wheel cylinder in the following 3 modes: pressure reduction, pressure holding and pressure increase modes.

X124758E03
0.167,1.073 1.719,1.281 1.552,0.208 10 false Front Speed Sensor RH 0.167,1.656 1.667,1.885 1.5,0.229 10 false Front Speed Sensor LH 0.167,2.229 2.146,2.667 1.979,0.438 10 false Rear Speed Sensor (Rear Axle Hub and Bearing Assembly RH) 0.177,3.01 2.125,3.448 1.948,0.438 10 false Rear Speed Sensor (Rear Axle Hub and Bearing Assembly LH) 0.167,3.792 2.146,4.052 1.979,0.26 10 false Brake Booster Pump Assembly 0.198,4.365 1.906,4.76 1.708,0.396 10 false Brake Pedal Stroke Sensor Assembly 0.177,5.146 1.958,5.375 1.781,0.229 10 false Stop Light Switch Assembly 4.969,1.063 6.615,1.458 1.646,0.396 10 false Pressure Control Solenoid Valve (2) 4.969,1.854 6.771,2.104 1.802,0.25 10 false Switching Solenoid Valve (4) 4.969,2.406 6.635,2.833 1.667,0.427 10 false Pressure Holding Solenoid Valve (4) 4.969,3.219 6.813,3.615 1.844,0.396 10 false Pressure Reduction Solenoid Valve (4) 0.271,6.094 1.969,6.458 1.698,0.365 10 false Yaw Rate and Acceleration Sensor 0.198,5.719 1.833,5.948 1.635,0.229 10 false Airbag Sensor Assembly 0.177,7 2.063,7.219 1.885,0.219 10 false Combination Meter Assembly 4.979,4.302 6.698,4.521 1.719,0.219 10 false Regulator Pressure Sensor 4.979,5.417 6.542,5.823 1.563,0.406 10 false Wheel Cylinder Pressure Sensor 3.104,3.76 3.917,3.979 0.813,0.219 10 false Motor Relay 3.146,2.229 3.74,2.625 0.594,0.396 10 false Solenoid Relay 2.958,0.656 4.104,0.854 1.146,0.198 10 false Skid Control ECU 2.823,0.135 5.76,0.365 2.938,0.229 10 false Brake Booster with Master Cylinder Assembly 4.802,0.594 5.865,0.802 1.063,0.208 10 false Brake Actuator 2.229,7.438 3.146,7.677 0.917,0.24 10 false CAN (V Bus)

U111623E20
1.927,1.76 1.792,2.25 1.792,2.25 1.688,2.25 true 1.917,3.094 1.781,3.573 1.781,3.573 1.677,3.573 true 1.604,0.74 2.583,0.948 0.979,0.208 10 false Increase Mode 3.146,0.74 4.073,0.948 0.927,0.208 10 false Holding Mode 5.469,0.719 6.542,0.917 1.073,0.198 10 false Reduction Mode 0.385,1.531 1.479,1.896 1.094,0.365 10 false Pressure Holding Valve 1.25,2.156 1.677,2.448 0.427,0.292 10 false Port A 1.25,3.49 1.667,3.781 0.417,0.292 10 false Port B 0.229,2.917 1.479,3.313 1.25,0.396 10 false Pressure Reduction Valve 4.5,2.375 5.271,2.813 0.771,0.438 10 false to Reservoir and Pump 2.188,3.74 2.792,4.104 0.604,0.365 10 false to Wheel Cylinder 6.104,3.729 6.854,4.125 0.75,0.396 10 false from Wheel Cylinder

Not Activated Normal Braking - -
Activated Increase Mode Holding Mode Reduction Mode
Pressure Holding Solenoid Valve OFF (Open) ON (Close) ON (Close)
Pressure Reduction Solenoid Valve OFF (Close) OFF (Close) ON (Open)
Wheel Cylinder Pressure Increase Hold Reduce



e.

Brake Assist

i.

In the event of emergency braking, the skid control ECU detects the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, the fluid pressure from the accumulator is directed to the wheel cylinder to apply a greater fluid pressure than the regulator.

X108155E04
3.01,1.042 4.146,1.229 1.135,0.188 10 false Skid Control ECU 4.75,0.979 5.75,1.156 1,0.177 10 false Brake Actuator 2.75,0.438 5.667,0.646 2.917,0.208 10 false Brake Booster with Master Cylinder Assembly 3.135,2.75 3.729,3.146 0.594,0.396 10 false Solenoid Relay 4.927,1.479 6.573,1.875 1.646,0.396 10 false Pressure Control Solenoid Valve (2) 4.927,2.323 6.74,2.552 1.813,0.229 10 false Switching Solenoid Valve (4) 4.927,2.927 6.583,3.323 1.656,0.396 10 false Pressure Holding Solenoid Valve (4) 4.927,3.771 6.74,4.188 1.813,0.417 10 false Pressure Reduction Solenoid Valve (4) 4.927,5.448 6.49,5.833 1.563,0.385 10 false Wheel Cylinder Pressure Sensor 4.927,4.604 6.635,4.813 1.708,0.208 10 false Regulator Pressure Sensor 3.135,4.656 3.979,4.865 0.844,0.208 10 false Motor Relay 0.188,2.188 1.76,2.396 1.573,0.208 10 false Front Speed Sensor LH 0.188,1.479 1.74,1.677 1.552,0.198 10 false Front Speed Sensor RH 0.167,2.885 2.156,3.292 1.99,0.406 10 false Rear Speed Sensor (Rear Axle Hub and Bearing Assembly RH) 0.177,3.802 2.156,4.177 1.979,0.375 10 false Rear Speed Sensor (Rear Axle Hub and Bearing Assembly LH) 0.188,4.729 2.146,4.958 1.958,0.229 10 false Brake Booster Pump Assembly 0.188,5.438 1.896,5.792 1.708,0.354 10 false Brake Pedal Stroke Sensor Assembly

X104747E10
1.302,0.146 1.479,0.146 1.479,0.146 1.479,0.552 true 2.469,0.156 2.375,0.156 2.375,0.156 2.073,0.594 true 5.052,1.823 4.938,1.823 4.938,1.823 4.698,2.49 true 1.177,5.677 1.177,5.292 1.177,5.292 1.594,5.292 true 1.135,0.052 1.344,0.229 0.208,0.177 10 false *1 2.49,0.063 2.76,0.271 0.271,0.208 10 false *2 5.094,1.115 5.365,1.323 0.271,0.208 10 false *4 3.625,0.74 3.896,0.948 0.271,0.208 10 false *3 2.26,1.698 2.531,1.906 0.271,0.208 10 false *5 5.083,1.719 5.354,1.927 0.271,0.208 10 false *6 1.677,4.25 1.948,4.458 0.271,0.208 10 false *7 2.479,4.573 2.688,4.781 0.208,0.208 10 false *8 3.063,4.917 3.333,5.125 0.271,0.208 10 false *11 4.26,4.094 4.531,4.302 0.271,0.208 10 false *9 4.115,4.917 4.385,5.125 0.271,0.208 10 false *12 5.292,4.094 5.563,4.302 0.271,0.208 10 false *10 5.198,4.75 5.469,4.958 0.271,0.208 10 false *13 5.479,5.833 5.75,6.042 0.271,0.208 10 false *16 3.25,5.969 3.521,6.177 0.271,0.208 10 false *15 1.625,5.198 1.896,5.406 0.271,0.208 10 false *14 1.49,6.813 1.76,7.021 0.271,0.208 10 false *17 2.281,6.813 2.552,7.021 0.271,0.208 10 false *18 4.115,6.813 4.385,7.021 0.271,0.208 10 false *19 4.948,6.813 5.219,7.021 0.271,0.208 10 false *20 5.385,8.604 5.656,8.813 0.271,0.208 10 false *28 3.677,8.615 3.948,8.823 0.271,0.208 10 false *27 2.729,8.615 3,8.823 0.271,0.208 10 false *26 1.052,8.615 1.323,8.823 0.271,0.208 10 false *25 1.51,7.813 1.781,8.021 0.271,0.208 10 false *21 2.281,7.813 2.552,8.021 0.271,0.208 10 false *22 4.115,7.802 4.385,8.01 0.271,0.208 10 false *23 4.938,7.802 5.208,8.01 0.271,0.208 10 false *24 6.188,4.031 6.688,4.448 0.5,0.417 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item Normal Braking Increase Mode Brake Assist Activated
Pressure Control Solenoid Valve SLA On* On*
SLR Off (Close) Off (Close)
Switching Solenoid Valve SSC On (Open) On (Open)
SCC On (Open) On (Open)
SMC On (Close) On (Close)
SRC On (Close) On (Close)
Pressure Holding Solenoid Valve FLH Off (Open) Off (Open)
FRH Off (Open) Off (Open)
RLH Off (Open) Off (Open)
RRH Off (Open) Off (Open)
Pressure Reduction Solenoid Valve FLR Off (Close) Off (Close)
FRR Off (Close) Off (Close)
RLR Off (Close) Off (Close)
RRR Off (Close) Off (Close)

HINT:

*: The solenoid valve constantly regulates the amount of opening of the valve in accordance with the use conditions in order to control the fluid pressure.




f.

TRC

i.

The fluid pressure stored in the accumulator is regulated by the switching solenoid valves and control solenoid valves to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes to control the slippage of the drive wheels. The diagram below shows the hydraulic circuit in the pressure increase mode when the TRC is activated. The pressure holding solenoid valve and the pressure reduction solenoid valve are turned on/off according to the ABS with EBD operation pattern.

X124759E05
4.813,5.875 5.979,6.052 1.167,0.177 10 false VSC OFF Switch 0.219,6.854 2.01,7.042 1.792,0.188 10 false Hybrid Vehicle Control ECU 0.177,0.958 1.698,1.146 1.521,0.188 10 false Front Speed Sensor LH 0.177,0.51 1.76,0.719 1.583,0.208 10 false Front Speed Sensor RH 0.177,1.406 2.146,1.781 1.969,0.375 10 false Rear Speed Sensor (Rear Axle Hub and Bearing Assembly RH) 0.188,2.208 2.156,2.573 1.969,0.365 10 false Rear Speed Sensor (Rear Axle Hub and Bearing Assembly LH) 0.188,3.156 2.156,3.375 1.969,0.219 10 false Brake Booster Pump Assembly 0.208,3.615 1.792,3.833 1.583,0.219 10 false Airbag Sensor Assembly 0.281,3.969 1.979,4.333 1.698,0.365 10 false Yaw Rate and Acceleration Sensor 0.24,4.854 1.792,5.198 1.552,0.344 10 false Spiral Cable with Sensor Sub-assembly 0.26,5.531 1.792,5.75 1.531,0.219 10 false Steering Angle Sensor 0.208,6.083 2.094,6.302 1.885,0.219 10 false Combination Meter Assembly 3.115,0.115 6.042,0.333 2.927,0.219 10 false Brake Booster with Master Cylinder Assembly 3.292,0.5 4.396,0.708 1.104,0.208 10 false Skid Control ECU 3.458,1.823 4.052,2.24 0.594,0.417 10 false Solenoid Relay 3.458,3.26 4.26,3.5 0.802,0.24 10 false Motor Relay 4.979,0.865 6.635,1.219 1.656,0.354 10 false Pressure Control Solenoid Valve (2) 4.979,1.625 6.813,1.854 1.833,0.229 10 false Switching Solenoid Valve (4) 4.979,2.031 6.667,2.469 1.688,0.438 10 false Pressure Holding Solenoid Valve (4) 4.979,2.781 6.823,3.156 1.844,0.375 10 false Pressure Reduction Solenoid Valve (4) 4.979,3.865 6.75,4.083 1.771,0.219 10 false Regulator Pressure Sensor 4.979,4.719 6.552,5.094 1.573,0.375 10 false Wheel Cylinder Pressure Sensor 4.813,0.479 5.979,0.677 1.167,0.198 10 false Brake Actuator 1.896,7.51 3.042,7.719 1.146,0.208 10 false CAN (Sub bus 15) 2.25,3.781 3.198,4.125 0.948,0.344 10 false CAN (V Bus)

X104748E03
1.302,0.135 1.479,0.135 1.479,0.135 1.479,0.542 false 2.469,0.177 2.375,0.177 2.375,0.177 2.073,0.615 false 5.063,1.844 4.948,1.844 4.948,1.844 4.708,2.51 false 1.198,5.667 1.198,5.281 1.198,5.281 1.615,5.281 false 1.094,0.052 1.365,0.26 0.271,0.208 10 false *1 2.51,0.104 2.781,0.313 0.271,0.208 10 false *2 5.156,1.135 5.427,1.344 0.271,0.208 10 false *4 3.625,0.75 3.896,0.958 0.271,0.208 10 false *3 2.292,1.708 2.563,1.917 0.271,0.208 10 false *5 5.104,1.76 5.375,1.969 0.271,0.208 10 false *6 1.667,4.26 1.938,4.469 0.271,0.208 10 false *7 2.479,4.604 2.688,4.813 0.208,0.208 10 false *8 3.083,4.927 3.354,5.135 0.271,0.208 10 false *11 4.302,4.219 4.573,4.427 0.271,0.208 10 false *9 4.156,4.927 4.427,5.135 0.271,0.208 10 false *12 5.323,4.24 5.594,4.448 0.271,0.208 10 false *10 5.25,4.802 5.521,5.01 0.271,0.208 10 false *13 5.479,5.833 5.75,6.042 0.271,0.208 10 false *16 3.25,5.979 3.521,6.188 0.271,0.208 10 false *15 1.667,5.219 1.938,5.427 0.271,0.208 10 false *14 1.49,6.802 1.76,7.01 0.271,0.208 10 false *17 2.302,6.802 2.573,7.01 0.271,0.208 10 false *18 4.146,6.802 4.417,7.01 0.271,0.208 10 false *19 4.948,6.792 5.219,7 0.271,0.208 10 false *20 5.406,8.604 5.677,8.813 0.271,0.208 10 false *28 3.688,8.604 3.958,8.813 0.271,0.208 10 false *27 2.75,8.604 3.021,8.813 0.271,0.208 10 false *26 1.063,8.594 1.333,8.802 0.271,0.208 10 false *25 1.479,7.813 1.75,8.021 0.271,0.208 10 false *21 2.281,7.792 2.552,8 0.271,0.208 10 false *22 4.115,7.781 4.385,7.99 0.271,0.208 10 false *23 4.938,7.781 5.208,7.99 0.271,0.208 10 false *24 6.229,4.052 6.729,4.469 0.5,0.417 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item TRC not Activated TRC Activated
Increase Mode Holding Mode Reduction Mode
Pressure Control Solenoid Valve SLA Off (Close) On (Open) On (Open) On (Open)
SLR Off (Close) Off (Close) Off (Close) Off (Close)
Switching Solenoid Valve SSC On (Open) On (Open) On (Open) On (Open)
SCC On (Open) On (Open) On (Open) On (Open)
SMC Off (Open) On (Close) On (Close) On (Close)
SRC Off (Open) On (Close) On (Close) On (Close)
Pressure Holding Solenoid Valve FLH Off (Open) Off (Open) On (Close) On (Close)
FRH Off (Open) Off (Open) On (Close) On (Close)
RLH Off (Open) On (Close) On (Close) On (Close)
RRH Off (Open) On (Close) On (Close) On (Close)
Pressure Reduction Solenoid Valve FLR Off (Close) Off (Close) Off (Close) On (Open)
FRR Off (Close) Off (Close) Off (Close) On (Open)
RLR Off (Close) Off (Close) Off (Close) Off (Close)
RRR Off (Close) Off (Close) Off (Close) Off (Close)



g.

VSC

i.

The VSC, by way of solenoid valves, controls the fluid pressure that is stored in the accumulator and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure holding and pressure increase modes. As a result, the tendency to front wheel skid or rear wheel skid is controlled.

X124759E06
4.833,5.865 6.063,6.083 1.229,0.219 10 false VSC OFF Switch 0.219,6.844 1.99,7.052 1.771,0.208 10 false Hybrid Vehicle Control ECU 0.198,0.948 1.781,1.167 1.583,0.219 10 false Front Speed Sensor LH 0.177,0.51 1.802,0.74 1.625,0.229 10 false Front Speed Sensor RH 0.188,1.406 2.156,1.781 1.969,0.375 10 false Rear Speed Sensor (Rear Axle Hub and Bearing Assembly RH) 0.177,2.198 2.146,2.573 1.969,0.375 10 false Rear Speed Sensor (Rear Axle Hub and Bearing Assembly LH) 0.177,3.177 2.156,3.396 1.979,0.219 10 false Brake Booster Pump Assembly 0.229,3.615 1.885,3.865 1.656,0.25 10 false Airbag Sensor Assembly 0.281,3.979 2,4.323 1.719,0.344 10 false Yaw Rate and Acceleration Sensor 0.198,4.833 1.74,5.219 1.542,0.385 10 false Spiral Cable with Sensor Sub-assembly 0.26,5.542 1.781,5.74 1.521,0.198 10 false Steering Angle Sensor 0.229,6.083 2.115,6.281 1.885,0.198 10 false Combination Meter Assembly 3.115,0.094 6.073,0.302 2.958,0.208 10 false Brake Booster with Master Cylinder Assembly 3.292,0.51 4.406,0.76 1.115,0.25 10 false Skid Control ECU 3.448,1.75 4.031,2.156 0.583,0.406 10 false Solenoid Relay 3.458,3.26 4.271,3.469 0.813,0.208 10 false Motor Relay 4.979,0.885 6.656,1.229 1.677,0.344 10 false Pressure Control Solenoid Valve (2) 4.979,1.625 6.813,1.844 1.833,0.219 10 false Switching Solenoid Valve (4) 4.979,2.031 6.646,2.417 1.667,0.385 10 false Pressure Holding Solenoid Valve (4) 4.979,2.802 6.792,3.167 1.813,0.365 10 false Pressure Reduction Solenoid Valve (4) 4.969,3.865 6.698,4.083 1.729,0.219 10 false Regulator Pressure Sensor 4.969,4.729 6.51,5.104 1.542,0.375 10 false Wheel Cylinder Pressure Sensor 4.813,0.479 5.875,0.688 1.063,0.208 10 false Brake Actuator 1.906,7.51 3.115,7.74 1.208,0.229 10 false CAN (Sub bus 15) 2.229,3.792 3.063,4.031 0.833,0.24 10 false CAN (V Bus)


ii.

In the front wheel skid restraining control, the brakes of the front wheels and rear wheel of the inner circle of the turn is applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle makes a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation pattern.

X104749E10
1.302,0.135 1.479,0.135 1.479,0.135 1.479,0.542 true 2.469,0.167 2.375,0.167 2.375,0.167 2.073,0.604 true 5.052,1.781 4.938,1.781 4.938,1.781 4.698,2.448 true 1.177,5.667 1.177,5.281 1.177,5.281 1.594,5.281 true 1.135,0.042 1.406,0.25 0.271,0.208 10 false *1 2.51,0.073 2.781,0.281 0.271,0.208 10 false *2 5.094,1.094 5.365,1.302 0.271,0.208 10 false *4 3.625,0.74 3.896,0.948 0.271,0.208 10 false *3 2.25,1.708 2.521,1.917 0.271,0.208 10 false *5 5.083,1.677 5.354,1.885 0.271,0.208 10 false *6 1.677,4.26 1.948,4.469 0.271,0.208 10 false *7 2.479,4.573 2.688,4.781 0.208,0.208 10 false *8 3.063,4.906 3.333,5.115 0.271,0.208 10 false *11 4.26,4.219 4.531,4.427 0.271,0.208 10 false *9 4.115,4.917 4.385,5.125 0.271,0.208 10 false *12 5.271,4.208 5.542,4.417 0.271,0.208 10 false *10 5.188,4.781 5.458,4.99 0.271,0.208 10 false *13 5.479,5.802 5.75,6.01 0.271,0.208 10 false *16 3.25,5.938 3.521,6.146 0.271,0.208 10 false *15 1.625,5.188 1.896,5.396 0.271,0.208 10 false *14 1.469,6.771 1.74,6.979 0.271,0.208 10 false *17 2.292,6.771 2.563,6.979 0.271,0.208 10 false *18 4.125,6.771 4.396,6.979 0.271,0.208 10 false *19 4.927,6.771 5.198,6.979 0.271,0.208 10 false *20 5.375,8.573 5.646,8.781 0.271,0.208 10 false *28 3.667,8.573 3.938,8.781 0.271,0.208 10 false *27 2.729,8.573 3,8.781 0.271,0.208 10 false *26 1.052,8.573 1.323,8.781 0.271,0.208 10 false *25 1.479,7.76 1.75,7.969 0.271,0.208 10 false *21 2.281,7.76 2.552,7.969 0.271,0.208 10 false *22 4.115,7.76 4.385,7.969 0.271,0.208 10 false *23 4.938,7.76 5.208,7.969 0.271,0.208 10 false *24 6.188,4.01 6.688,4.427 0.5,0.417 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item VSC not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Pressure Control Solenoid Valve SLA Off (Close) On (Open) On (Open) On (Open)
SLR Off (Close) Off (Close) Off (Close) Off (Close)
Switching Solenoid Valve SSC On (Open) On (Open) On (Open) On (Open)
SCC On (Open) On (Open) On (Open) On (Open)
SMC Off (Open) On (Close) On (Close) On (Close)
SRC Off (Open) On (Close) On (Close) On (Close)
Pressure Holding Solenoid Valve FLH Off (Open) Off (Open) On (Close) On (Close)
FRH Off (Open) Off (Open) On (Close) On (Close)
RLH Off (Open) On (Close) On (Close) On (Close)
RRH Off (Open) Off (Open) On (Close) On (Close)
Pressure Reduction Solenoid Valve FLR Off (Close) Off (Close) Off (Close) On (Open)
FRR Off (Close) Off (Close) Off (Close) On (Open)
RLR Off (Close) Off (Close) Off (Close) Off (Close)
RRR Off (Close) Off (Close) Off (Close) On (Open)


iii.

In the rear wheel skid restraining control, the brakes of the front and rear wheels on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the rear wheel skid condition while the vehicle makes a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation patterns.

X104750E11
1.302,0.125 1.479,0.125 1.479,0.125 1.479,0.531 true 2.469,0.156 2.375,0.156 2.375,0.156 2.073,0.594 true 5.052,1.833 4.938,1.833 4.938,1.833 4.698,2.5 true 1.167,5.677 1.167,5.292 1.167,5.292 1.583,5.292 false 1.135,0.031 1.406,0.24 0.271,0.208 10 false *1 2.49,0.063 2.76,0.271 0.271,0.208 10 false *2 5.083,1.104 5.354,1.313 0.271,0.208 10 false *4 3.625,0.76 3.896,0.969 0.271,0.208 10 false *3 2.25,1.708 2.521,1.917 0.271,0.208 10 false *5 5.083,1.729 5.354,1.938 0.271,0.208 10 false *6 1.688,4.26 1.958,4.469 0.271,0.208 10 false *7 2.479,4.583 2.688,4.792 0.208,0.208 10 false *8 3.052,4.938 3.323,5.146 0.271,0.208 10 false *11 4.24,4.25 4.51,4.458 0.271,0.208 10 false *9 4.094,4.938 4.365,5.146 0.271,0.208 10 false *12 5.271,4.24 5.542,4.448 0.271,0.208 10 false *10 5.188,4.792 5.458,5 0.271,0.208 10 false *13 5.458,5.833 5.729,6.042 0.271,0.208 10 false *16 3.229,5.958 3.5,6.167 0.271,0.208 10 false *15 1.615,5.198 1.885,5.406 0.271,0.208 10 false *14 1.49,6.792 1.76,7 0.271,0.208 10 false *17 2.302,6.792 2.573,7 0.271,0.208 10 false *18 4.135,6.781 4.406,6.99 0.271,0.208 10 false *19 4.938,6.792 5.208,7 0.271,0.208 10 false *20 5.365,8.583 5.635,8.792 0.271,0.208 10 false *28 3.646,8.594 3.917,8.802 0.271,0.208 10 false *27 2.708,8.583 2.979,8.792 0.271,0.208 10 false *26 1.031,8.583 1.302,8.792 0.271,0.208 10 false *25 1.479,7.792 1.75,8 0.271,0.208 10 false *21 2.281,7.792 2.552,8 0.271,0.208 10 false *22 4.115,7.792 4.385,8 0.271,0.208 10 false *23 4.938,7.781 5.208,7.99 0.271,0.208 10 false *24 6.188,4.042 6.688,4.458 0.5,0.417 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item VSC not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Pressure Control Solenoid Valve SLA Off (Close) On (Open) On (Open) On (Open)
SLR Off (Close) Off (Close) Off (Close) Off (Close)
Switching Solenoid Valve SSC On (Open) On (Open) On (Open) On (Open)
SCC On (Open) On (Open) On (Open) On (Open)
SMC Off (Open) On (Close) On (Close) On (Close)
SRC Off (Open) On (Close) On (Close) On (Close)
Pressure Holding Solenoid Valve FLH Off (Open) Off (Open) On (Close) On (Close)
FRH Off (Open) On (Close) On (Close) On (Close)
RLH Off (Open) Off (Open) On (Close) On (Close)
RRH Off (Open) On (Close) On (Close) On (Close)
Pressure Reduction Solenoid Valve FLR Off (Close) Off (Close) Off (Close) On (Open)
FRR Off (Close) Off (Close) Off (Close) Off (Close)
RLR Off (Close) Off (Close) Off (Close) On (Open)
RRR Off (Close) Off (Close) Off (Close) Off (Close)



h.

Hill-start Assist Control

i.

Hill-start Assist Control helps maintain 4-wheel hydraulic pressure by operating the pressure control solenoid valve when the driver releases the brake pedal until depressing the accelerator pedal.


ii.

Based on the information provided by various sensors, switches, and the hybrid vehicle control ECU, the skid control ECU determines whether to activate Hill-start Assist Control.

X124760E03
4.917,7.104 6.729,7.333 1.813,0.229 10 false Stop Light Switch Assembly 0.198,6.854 1.948,7.094 1.75,0.24 10 false Hybrid Vehicle Control ECU 0.177,0.896 1.771,1.094 1.594,0.198 10 false Front Speed Sensor LH 0.177,0.469 1.729,0.656 1.552,0.188 10 false Front Speed Sensor RH 0.177,1.333 2.146,1.698 1.969,0.365 10 false Rear Speed Sensor (Rear Axle Hub and Bearing Assembly RH) 0.177,2.125 2.146,2.469 1.969,0.344 10 false Rear Speed Sensor (Rear Axle Hub and Bearing Assembly LH) 0.177,2.885 1.896,3.26 1.719,0.375 10 false Brake Pedal Stroke Sensor Assembly 0.177,3.646 2.156,3.854 1.979,0.208 10 false Brake Booster Pump Assembly 0.198,4.115 1.844,4.344 1.646,0.229 10 false Airbag Sensor Assembly 0.25,4.458 1.938,4.854 1.688,0.396 10 false Yaw Rate and Acceleration Sensor 0.198,5.344 2.083,5.563 1.885,0.219 10 false Combination Meter Assembly 0.219,6.083 1.865,6.469 1.646,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 3.125,0.094 6.021,0.344 2.896,0.25 10 false Brake Booster with Master Cylinder Assembly 3.302,0.531 4.417,0.74 1.115,0.208 10 false Skid Control ECU 3.427,2.146 4.042,2.49 0.615,0.344 10 false Solenoid Relay 3.458,3.729 4.25,3.958 0.792,0.229 10 false Motor Relay 4.99,1.052 6.646,1.417 1.656,0.365 10 false Pressure Control Solenoid Valve (2) 4.969,1.906 6.802,2.125 1.833,0.219 10 false Switching Solenoid Valve (4) 4.979,2.354 6.635,2.719 1.656,0.365 10 false Pressure Holding Solenoid Valve (4) 4.969,3.188 6.781,3.552 1.813,0.365 10 false Pressure Reduction Solenoid Valve (4) 4.979,4.354 6.698,4.563 1.719,0.208 10 false Regulator Pressure Sensor 4.979,5.5 6.563,5.854 1.583,0.354 10 false Wheel Cylinder Pressure Sensor 4.813,0.531 5.917,0.74 1.104,0.208 10 false Brake Actuator 1.917,7.552 3.083,7.792 1.167,0.24 10 false CAN (Sub bus 15) 2.26,4.25 3.208,4.594 0.948,0.344 10 false CAN (V Bus)

X104751E10
1.302,0.146 1.479,0.146 1.479,0.146 1.479,0.552 true 2.458,0.177 2.365,0.177 2.365,0.177 2.063,0.615 true 5.021,1.875 4.906,1.875 4.906,1.875 4.667,2.542 true 1.167,5.677 1.167,5.292 1.167,5.292 1.583,5.292 true 1.135,0.052 1.406,0.26 0.271,0.208 10 false *1 2.5,0.094 2.771,0.302 0.271,0.208 10 false *2 5.094,1.125 5.365,1.333 0.271,0.208 10 false *4 3.625,0.74 3.896,0.948 0.271,0.208 10 false *3 2.26,1.719 2.531,1.927 0.271,0.208 10 false *5 5.063,1.771 5.333,1.979 0.271,0.208 10 false *6 1.677,4.25 1.948,4.458 0.271,0.208 10 false *7 2.5,4.573 2.708,4.781 0.208,0.208 10 false *8 3.073,4.938 3.344,5.146 0.271,0.208 10 false *11 4.26,4.25 4.531,4.458 0.271,0.208 10 false *9 4.115,4.927 4.385,5.135 0.271,0.208 10 false *12 5.281,4.229 5.552,4.438 0.271,0.208 10 false *10 5.219,4.792 5.49,5 0.271,0.208 10 false *13 5.479,5.833 5.75,6.042 0.271,0.208 10 false *16 3.25,5.969 3.521,6.177 0.271,0.208 10 false *15 1.615,5.198 1.885,5.406 0.271,0.208 10 false *14 1.5,6.802 1.771,7.01 0.271,0.208 10 false *17 2.281,6.813 2.552,7.021 0.271,0.208 10 false *18 4.125,6.802 4.396,7.01 0.271,0.208 10 false *19 4.938,6.802 5.208,7.01 0.271,0.208 10 false *20 5.375,8.583 5.646,8.792 0.271,0.208 10 false *28 3.667,8.583 3.938,8.792 0.271,0.208 10 false *27 2.729,8.583 3,8.792 0.271,0.208 10 false *26 1.052,8.583 1.323,8.792 0.271,0.208 10 false *25 1.49,7.781 1.76,7.99 0.271,0.208 10 false *21 2.281,7.792 2.552,8 0.271,0.208 10 false *22 4.115,7.792 4.385,8 0.271,0.208 10 false *23 4.938,7.781 5.208,7.99 0.271,0.208 10 false *24 6.177,4.042 6.677,4.458 0.5,0.417 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item Hill-start Assist Control not Activated Hill-start Assist Control Activated
Holding Mode Reduction Mode
Pressure Control Solenoid Valve SLA Off (Close) Off (Close) Off (Close)
SLR Off (Close) Off (Close) On (Open)
Switching Solenoid Valve SSC On (Open) On (Open) On (Open)
SCC On (Open) On (Open) On (Open)
SMC Off (Open) On (Close) On (Close)
SRC Off (Open) On (Close) On (Close)
Pressure Holding Solenoid Valve FLH Off (Open) Off (Open) Off (Open)
FRH Off (Open) Off (Open) Off (Open)
RLH Off (Open) Off (Open) Off (Open)
RRH Off (Open) Off (Open) Off (Open)
Pressure Reduction Solenoid Valve FLR Off (Close) Off (Close) Off (Close)
FRR Off (Close) Off (Close) Off (Close)
RLR Off (Close) Off (Close) Off (Close)
RRR Off (Close) Off (Close) Off (Close)




FAIL-SAFE


a.

Brake System

i.

When the brake actuator stops, the switching solenoid valves SSC and SCC close and the switching solenoid valves SMC and SRC open. Thus, the fluid pressure generated in the hydraulic brake booster by the driver's brake pedal operation is directly supplied to each of the wheel cylinders.

X104752E12
1.302,0.156 1.479,0.156 1.479,0.156 1.479,0.563 true 2.469,0.167 2.375,0.167 2.375,0.167 2.073,0.604 true 5.052,1.844 4.938,1.844 4.938,1.844 4.698,2.51 true 1.167,5.677 1.167,5.292 1.167,5.292 1.583,5.292 true 1.125,0.063 1.396,0.271 0.271,0.208 10 false *1 2.51,0.063 2.781,0.271 0.271,0.208 10 false *2 5.094,1.104 5.365,1.313 0.271,0.208 10 false *4 3.625,0.76 3.896,0.969 0.271,0.208 10 false *3 2.25,1.719 2.521,1.927 0.271,0.208 10 false *5 5.083,1.74 5.354,1.948 0.271,0.208 10 false *6 1.667,4.25 1.938,4.458 0.271,0.208 10 false *7 2.479,4.583 2.688,4.792 0.208,0.208 10 false *8 3.083,4.885 3.354,5.094 0.271,0.208 10 false *11 4.26,4.229 4.531,4.438 0.271,0.208 10 false *9 4.156,4.885 4.427,5.094 0.271,0.208 10 false *12 5.281,4.229 5.552,4.438 0.271,0.208 10 false *10 5.25,4.75 5.521,4.958 0.271,0.208 10 false *13 5.479,5.833 5.75,6.042 0.271,0.208 10 false *16 3.25,5.969 3.521,6.177 0.271,0.208 10 false *15 1.615,5.198 1.885,5.406 0.271,0.208 10 false *14 1.49,6.802 1.76,7.01 0.271,0.208 10 false *17 2.302,6.802 2.573,7.01 0.271,0.208 10 false *18 4.115,6.802 4.385,7.01 0.271,0.208 10 false *19 4.917,6.802 5.188,7.01 0.271,0.208 10 false *20 5.354,8.604 5.625,8.813 0.271,0.208 10 false *28 3.656,8.604 3.927,8.813 0.271,0.208 10 false *27 2.729,8.594 3,8.802 0.271,0.208 10 false *26 1.042,8.594 1.313,8.802 0.271,0.208 10 false *25 1.479,7.813 1.75,8.021 0.271,0.208 10 false *21 2.281,7.802 2.552,8.01 0.271,0.208 10 false *22 4.115,7.802 4.385,8.01 0.271,0.208 10 false *23 4.938,7.813 5.208,8.021 0.271,0.208 10 false *24 6.198,4.042 6.698,4.458 0.5,0.417 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item System Off
Pressure Control Solenoid Valve SLA Off (Close)
SLR Off (Close)
Switching Solenoid Valve SSC Off (Close)
SCC Off (Close)
SMC Off (Open)
SRC Off (Open)
Pressure Holding Solenoid Valve FLH Off (Open)
FRH Off (Open)
RLH Off (Open)
RRH Off (Open)
Pressure Reduction Solenoid Valve FLR Off (Close)
FRR Off (Close)
RLR Off (Close)
RRR Off (Close)


ii.

When the accumulator pressure is not supplied due to a failure in the brake system, the skid control ECU closes the switching solenoid valves SSC and SCC and opens the switching solenoid valves SMC and SRC. At this time, the fluid pressure generated in the master cylinder of the hydraulic brake booster is supplied only to the front wheel cylinder.

X104753E10
1.302,0.156 1.479,0.156 1.479,0.156 1.479,0.563 true 2.469,0.167 2.375,0.167 2.375,0.167 2.073,0.604 true 5.052,1.854 4.938,1.854 4.938,1.854 4.698,2.521 true 1.167,5.698 1.167,5.313 1.167,5.313 1.583,5.313 true 1.125,0.063 1.396,0.271 0.271,0.208 10 false *1 2.5,0.073 2.771,0.281 0.271,0.208 10 false *2 5.094,1.115 5.365,1.323 0.271,0.208 10 false *4 3.625,0.698 3.896,0.906 0.271,0.208 10 false *3 2.281,1.708 2.552,1.917 0.271,0.208 10 false *5 5.083,1.74 5.354,1.948 0.271,0.208 10 false *6 1.667,4.26 1.938,4.469 0.271,0.208 10 false *7 2.479,4.573 2.688,4.781 0.208,0.208 10 false *8 3.083,4.885 3.354,5.094 0.271,0.208 10 false *11 4.271,4.219 4.542,4.427 0.271,0.208 10 false *9 4.156,4.885 4.427,5.094 0.271,0.208 10 false *12 5.292,4.219 5.563,4.427 0.271,0.208 10 false *10 5.25,4.75 5.521,4.958 0.271,0.208 10 false *13 5.469,5.865 5.74,6.073 0.271,0.208 10 false *16 3.229,5.99 3.5,6.198 0.271,0.208 10 false *15 1.604,5.219 1.875,5.427 0.271,0.208 10 false *14 1.479,6.813 1.75,7.021 0.271,0.208 10 false *17 2.302,6.813 2.573,7.021 0.271,0.208 10 false *18 4.115,6.802 4.385,7.01 0.271,0.208 10 false *19 4.927,6.813 5.198,7.021 0.271,0.208 10 false *20 5.375,8.615 5.646,8.823 0.271,0.208 10 false *28 3.656,8.615 3.927,8.823 0.271,0.208 10 false *27 2.719,8.615 2.99,8.823 0.271,0.208 10 false *26 1.031,8.615 1.302,8.823 0.271,0.208 10 false *25 1.479,7.813 1.75,8.021 0.271,0.208 10 false *21 2.281,7.813 2.552,8.021 0.271,0.208 10 false *22 4.104,7.813 4.375,8.021 0.271,0.208 10 false *23 4.927,7.813 5.198,8.021 0.271,0.208 10 false *24 6.198,4.021 6.698,4.438 0.5,0.417 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item Power Supply Malfunction
Pressure Control Solenoid Valve SLA Off (Close)
SLR Off (Close)
Switching Solenoid Valve SSC Off (Close)
SCC Off (Close)
SMC Off (Open)
SRC Off (Open)
Pressure Holding Solenoid Valve FLH Off (Open)
FRH Off (Open)
RLH Off (Open)
RRH Off (Open)
Pressure Reduction Solenoid Valve FLR Off (Close)
FRR Off (Close)
RLR Off (Close)
RRR Off (Close)


iii.

When the skid control ECU detects a malfunction of the front brake system, it closes the switching solenoid valves SSC and SCC and opens the switching solenoid valves SMC and SRC. At this time, the fluid pressure generated in the regulator in the hydraulic brake booster by the driver's brake pedal operation is directly supplied to the rear wheel cylinder.

X104754E11
1.302,0.146 1.479,0.146 1.479,0.146 1.479,0.552 true 2.469,0.177 2.375,0.177 2.375,0.177 2.073,0.615 true 5.052,1.865 4.938,1.865 4.938,1.865 4.698,2.531 true 1.167,5.688 1.167,5.302 1.167,5.302 1.583,5.302 true 1.125,0.063 1.396,0.271 0.271,0.208 10 false *1 2.51,0.073 2.781,0.281 0.271,0.208 10 false *2 5.104,1.115 5.375,1.323 0.271,0.208 10 false *4 3.625,0.729 3.896,0.938 0.271,0.208 10 false *3 2.26,1.729 2.531,1.938 0.271,0.208 10 false *5 5.083,1.76 5.354,1.969 0.271,0.208 10 false *6 1.667,4.271 1.938,4.479 0.271,0.208 10 false *7 2.479,4.583 2.688,4.792 0.208,0.208 10 false *8 3.083,4.885 3.354,5.094 0.271,0.208 10 false *11 4.271,4.24 4.542,4.448 0.271,0.208 10 false *9 4.156,4.885 4.427,5.094 0.271,0.208 10 false *12 5.292,4.229 5.563,4.438 0.271,0.208 10 false *10 5.25,4.75 5.521,4.958 0.271,0.208 10 false *13 5.469,5.844 5.74,6.052 0.271,0.208 10 false *16 3.25,5.958 3.521,6.167 0.271,0.208 10 false *15 1.604,5.208 1.875,5.417 0.271,0.208 10 false *14 1.49,6.792 1.76,7 0.271,0.208 10 false *17 2.281,6.802 2.552,7.01 0.271,0.208 10 false *18 4.104,6.802 4.375,7.01 0.271,0.208 10 false *19 4.906,6.802 5.177,7.01 0.271,0.208 10 false *20 5.365,8.604 5.635,8.813 0.271,0.208 10 false *28 3.656,8.604 3.927,8.813 0.271,0.208 10 false *27 2.729,8.604 3,8.813 0.271,0.208 10 false *26 1.031,8.604 1.302,8.813 0.271,0.208 10 false *25 1.458,7.792 1.729,8 0.271,0.208 10 false *21 2.271,7.792 2.542,8 0.271,0.208 10 false *22 4.115,7.792 4.385,8 0.271,0.208 10 false *23 4.938,7.792 5.208,8 0.271,0.208 10 false *24 6.229,4.01 6.729,4.427 0.5,0.417 10 false *29

Text in Illustration
*1 Reservoir Tank *2 Brake Fluid Level Warning Switch
*3 Accumulator *4 Pump Motor
*5 Pressure Relief Valve *6 Hydraulic Brake Booster
*7 Stroke Simulator *8 Switching Solenoid Valve SSC
*9 Regulator Pressure Sensor *10 Accumulator Pressure Sensor
*11 Switching Solenoid Valve SMC *12 Switching Solenoid Valve SRC
*13 Pressure Control Solenoid Valve SLA *14 Wheel Cylinder Pressure Sensor
*15 Switching Solenoid Valve SCC *16 Pressure Control Solenoid Valve SLR
*17 Pressure Holding Solenoid Valve FLH *18 Pressure Holding Solenoid Valve FRH
*19 Pressure Holding Solenoid Valve RLH *20 Pressure Holding Solenoid Valve RRH
*21 Pressure Reduction Solenoid Valve FLR *22 Pressure Reduction Solenoid Valve FRR
*23 Pressure Reduction Solenoid Valve RLR *24 Pressure Reduction Solenoid Valve RRR
*25 Front Left Wheel Cylinder *26 Front Right Wheel Cylinder
*27 Rear Left Wheel Cylinder *28 Rear Right Wheel Cylinder
*29 Brake Actuator - -

Item When Front Brake Malfunction
Pressure Control Solenoid Valve SLA Off (Close)
SLR Off (Close)
Switching Solenoid Valve SSC Off (Close)
SCC Off (Close)
SMC Off (Open)
SRC Off (Open)
Pressure Holding Solenoid Valve FLH Off (Open)
FRH Off (Open)
RLH Off (Open)
RRH Off (Open)
Pressure Reduction Solenoid Valve FLR Off (Close)
FRR Off (Close)
RLR Off (Close)
RRR Off (Close)



b.

Skid Control ECU

i.

In the event of a malfunction of the ABS, the skid control ECU can control the EBD, if the EBD works properly.


ii.

In the event of a malfunction of the ABS and EBD, the skid control ECU will illuminate the brake warning lights to alert the driver of the malfunction and will disable brake control system operation.


iii.

In the event of a malfunction of the TRC and/or VSC, the skid control ECU will disable the TRC and VSC operation.


iv.

If a communication malfunction occurs between the skid control ECU and the steering angle sensor, yaw rate sensor or hybrid vehicle control ECU, the skid control ECU will disable the TRC and VSC operation.


v.

When the hybrid vehicle control ECU detects the Diagnostic Trouble Code (DTC), it will disable the TRC and VSC operation.




DIAGNOSIS


a.

If the skid control ECU detects a malfunction in the brake control system (ABS with EBD, brake assist, TRC and VSC), then the ABS warning light, brake warning light/red (malfunction), brake warning light/yellow (minor malfunction), slip indicator light will illuminate either individually or as a group according to the function in which the malfunction has been detected, to alert the driver of the malfunction.


b.

At the same time, a Diagnostic Trouble Code (DTC) will be stored in memory.


c.

This system has a sensor signal check (test mode) function.


d.

For details of DTCs that are stored in skid control ECU memory and DTCs that are output through the sensor signal check functions, see the Repair Manual.