Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2014.12
NM2170E _55 Steering _056979 POWER ASSIST SYSTEMS _0277775 POWER STEERING SYSTEM UN GENERAL/CONTROL/DETAILS F

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the EPS system are as follows:

Component Function
Electric Power Steering Column Assembly Torque Sensor Detects the twist of the torsion bar, calculates the torque that is applied to the torsion bar by changing it into an electrical signal, and outputs this signal to the power steering ECU assembly.
Reduction Mechanism Reduces the speed of the power steering motor assembly through the use of a worm gear and a wheel gear and transmits it to the column shaft.
Power Steering Motor Assembly Generates assist torque in accordance with a current received from the power steering ECU assembly.
Power Steering ECU Assembly Actuates the power steering motor assembly mounted on the steering column assembly to provide assist torque, based on the signals received from various sensors and ECUs.
Hybrid Vehicle Control ECU Transmits the ready status signal to the power steering ECU assembly.
Brake Booster with Master Cylinder Assembly Skid Control ECU Transmits the vehicle speed signal to the power steering ECU assembly.
Combination Meter Assembly EPS Warning Light Illuminates to alert the driver when the power steering ECU assembly detects a malfunction in the EPS system.
Buzzer Sounds to alert the driver when the power steering ECU assembly detects a malfunction in the EPS system.



SYSTEM CONTROL


a.

The EPS system has the following controls:

Control Outline
Basic Control Calculates the assist current from the steering torque value and the vehicle speed, and actuates the power steering motor assembly.
Compensation Control Compensates with a force, according to the driver's steering maneuver, improving the comfort of steering.



CONSTRUCTION


a.

Steering Column Assembly

i.

The steering column assembly includes a torque sensor, power steering motor assembly and reduction mechanism.

X108140E03
3.823,1.51 4.167,1.031 4.167,1.031 4.385,1.031 true 1.958,6.313 2.302,5.833 2.302,5.833 2.521,5.833 true 5.76,6.458 6.104,6.938 6.104,6.938 6.323,6.938 true 4.208,6.333 4.115,5.823 4.115,5.823 3.896,5.823 true 4.427,0.927 4.698,1.177 0.271,0.25 10 false *1 3.302,5.542 3.573,5.792 0.271,0.25 10 false *b 3.719,5.74 3.99,5.99 0.271,0.25 10 false *c 0.5,5.531 0.771,5.781 0.271,0.25 10 false *a 2.542,5.75 2.813,6 0.271,0.25 10 false *2 6.365,6.844 6.635,7.094 0.271,0.25 10 false *3 3.74,3.469 4.01,3.719 0.271,0.25 10 false A 3.74,5.198 4.01,5.448 0.271,0.25 10 false A 1.865,4.552 2.135,4.802 0.271,0.25 10 false B 4.406,4.552 4.677,4.802 0.271,0.25 10 false B

Text in Illustration
*1 Steering Column Assembly *2 Torque Sensor
*3 Power Steering Motor Assembly - -
*a A-A Cross Section *b B-B Cross Section
*c Reduction Mechanism - -


ii.

The torque sensor with Hall ICs is used.


iii.

The torque sensor is built into the steering column assembly. A multipole magnet is mounted to the input shaft, and a yoke is mounted to the output shaft. The input and output shafts are joined by the torsion bar.


iv.

The magnetic convergence ring assembly contains Hall ICs, which face opposite to each other. The system detects the steering direction in accordance with the direction of the magnetic flux that the amount of change in the magnetic flux density based on the relative displacement of the multipole magnet and the yoke. The power steering ECU assembly monitors the torque sensor signals that are output by the two Hall ICs to detect malfunctions.

X106003E06
1.667,3.177 2.073,3.76 2.073,3.76 2.302,3.76 true 1.521,3.938 1.115,4.51 1.115,4.51 0.885,4.51 true 4.667,2.104 4.042,3.021 4.042,3.021 3.823,3.021 true 5.354,2.115 4.052,3.021 true 1.813,1.292 2.292,0.458 2.292,0.458 2.521,0.458 true 4.865,1.292 5.5,0.719 5.5,0.719 5.719,0.719 true 5.781,2 6.01,1.573 6.01,1.573 6.229,1.573 true 4.74,1.646 4.115,1.063 4.115,1.063 3.885,1.063 true 5.146,1.667 4.115,1.063 true 2.333,3.667 2.604,3.917 0.271,0.25 10 false *3 2.563,0.365 2.833,0.615 0.271,0.25 10 false *1 0.719,4.417 0.99,4.667 0.271,0.25 10 false *2 3.656,2.938 3.927,3.188 0.271,0.25 10 false *6 5.75,0.625 6.021,0.875 0.271,0.25 10 false *3 3.698,0.99 3.969,1.24 0.271,0.25 10 false *4 6.25,1.49 6.521,1.74 0.271,0.25 10 false *5

Text in Illustration
*1 Input Shaft *2 Output Shaft
*3 Torsion Bar *4 Multipole Magnet
*5 Hall IC *6 Yoke

X106004E06
4.865,1.302 6.167,1.708 1.302,0.406 10 false Power Steering ECU Assembly 1.521,0.208 2.646,0.458 1.125,0.25 10 false Torque Sensor 4.146,0.719 4.604,0.969 0.458,0.25 10 false TRQV 4.146,1.125 4.594,1.417 0.448,0.292 10 false TRQ1 4.125,1.531 4.594,1.813 0.469,0.281 10 false TRQG 4.156,2.156 4.594,2.406 0.438,0.25 10 false TRQ2 1.135,0.802 1.719,1.094 0.583,0.292 10 false Hall IC 1 1.115,1.865 1.823,2.125 0.708,0.26 10 false Hall IC 2

NOTICE:

After replacing the electric power steering column assembly, the power steering motor assembly or the power steering ECU assembly, calibration of the torque sensor zero point is required. For details, refer to the Repair Manual.



v.

A low inertia, low noise and high power output power steering motor assembly is used.


vi.

The power steering motor assembly consists of a rotor, stator and motor shaft.


vii.

The torque that is generated by the power steering motor assembly is transmitted via the joint to the reduction mechanism.


viii.

The reduction mechanism reduces the speed of the power steering motor assembly via the worm gear and the wheel gear, and transmits it to the column shaft.


ix.

The wheel gear is made of a high strength, low friction and low wear plastic material, to realize low noise and a lightweight construction.


x.

The worm gear is supported by the ball bearings in order to reduce noise and frictions.

X108141E03
5.01,1.313 5.625,0.375 5.625,0.375 5.823,0.375 true 1.708,1.531 1.469,1.083 1.469,1.083 1.271,1.083 true 3.052,1.521 2.604,0.688 2.604,0.688 2.406,0.688 true 3.406,1.583 2.76,0.281 2.76,0.281 2.563,0.281 true 2.375,1.635 2,0.833 2,0.833 1.802,0.833 true 5.156,2.198 5.458,2.74 5.458,2.74 5.646,2.74 true 3.49,1.708 3.969,2.885 3.969,2.885 4.156,2.885 true 2.323,2.542 1.865,3.375 1.865,3.375 1.677,3.375 true 2.688,2.802 2.979,3.333 2.979,3.333 3.167,3.333 true 5.844,0.281 6.115,0.531 0.271,0.25 10 false *4 1.094,1.01 1.365,1.26 0.271,0.25 10 false *1 2.229,0.615 2.5,0.865 0.271,0.25 10 false *1 2.375,0.198 2.646,0.448 0.271,0.25 10 false *3 1.635,0.75 1.906,1 0.271,0.25 10 false *2 3.198,3.24 3.469,3.49 0.271,0.25 10 false *7 5.667,2.646 5.938,2.896 0.271,0.25 10 false *5 4.177,2.792 4.448,3.042 0.271,0.25 10 false *6 1.5,3.292 1.771,3.542 0.271,0.25 10 false *8

Text in Illustration
*1 Ball Bearing *2 Worm Gear
*3 Joint *4 Rotor
*5 Stator *6 Motor Shaft
*7 Wheel Gear *8 Column Shaft




OPERATION


a.

Straightline Driving

i.

If the vehicle is driven straight and the driver does not turn the steering wheel, the yoke is located in the center between the N and S poles of the multipole magnet. Thus, no magnetic flux passes between the Hall ICs. In this case, the Hole ICs output a specified voltage to the power steering ECU assembly, to indicate that the steering wheel is in the neutral position. Therefore, it does not apply current to the motor.

X106006E06
2.281,1.344 1.948,0.667 1.948,0.667 1.729,0.667 true 4.875,1.688 5.104,1.24 5.104,1.24 5.323,1.24 true 4.885,1.979 5.104,2.438 5.104,2.438 5.323,2.438 true 1.948,2.156 1.563,2.771 1.563,2.771 1.333,2.771 true 1.156,2.677 1.427,2.927 0.271,0.25 10 false *2 5.354,1.146 5.625,1.396 0.271,0.25 10 false *3 5.354,2.344 5.625,2.594 0.271,0.25 10 false *4 1.552,0.583 1.823,0.833 0.271,0.25 10 false *1 2,1.74 2.271,1.99 0.271,0.25 10 false N 2.917,1.75 3.188,2 0.271,0.25 10 false N 3.844,1.75 4.115,2 0.271,0.25 10 false N 2.458,1.75 2.729,2 0.271,0.25 10 false S 3.385,1.75 3.656,2 0.271,0.25 10 false S

Text in Illustration
*1 Yoke *2 Multipole Magnet
*3 Hall IC 1 *4 Hall IC 2



b.

When Steering

i.

When a driver turns the steering wheel to the right or left, the twist that is created in the torsion bar creates a relative displacement between the multipole magnet and the yoke.


ii.

At this time, the magnetic flux from the N to S pole of the multipole magnet passes between the Hall ICs. The system detects the steered direction of the steering wheel in accordance with the direction opposite to each other. As a result, the output characteristics of the 2 Hall ICs are constantly opposite each other. The system monitors the different outputs of these Hall ICs in order to detect malfunction.


iii.

The magnetic flux density becomes higher as it gets closer to the center of the respective pole. A Hall IC converts these magnetic flux fluctuations into voltage fluctuations, in order to transmit the turning torque of the steering wheel to the power steering ECU assembly.


iv.

The magnetic flux density becomes higher as it gets closer to the center of the respective pole. A Hall IC converts these magnetic flux fluctuations into voltage fluctuations, in order to transmit the turning torque of the steering wheel to the power steering ECU assembly.

X106007E09
2.833,1.75 3.156,0.75 3.156,0.75 3.375,0.75 true 3.781,4.76 4.094,3.76 4.094,3.76 4.323,3.76 false 6.458,1.75 6.75,0.74 6.75,0.74 6.521,0.74 true 6.458,1.99 6.75,3 6.75,3 6.521,3 true 2.854,2.01 3.177,3.01 3.177,3.01 3.396,3.01 true 0.292,1.698 0.563,1.948 0.271,0.25 10 false N 1.094,2.76 2.042,3.01 0.948,0.25 10 false Right Turn 5.281,6.313 6.229,6.563 0.948,0.25 10 false Right Turn 0.948,4.781 1.542,5.01 0.594,0.229 10 false Voltage 4.354,3.646 5.458,3.885 1.104,0.24 10 false Neutral Position 3.229,5.99 5.177,6.24 1.948,0.25 10 false Twist Angle of Torsion Bar 4.677,2.75 5.625,3 0.948,0.25 10 false Left Turn 1.573,6.313 2.521,6.563 0.948,0.25 10 false Left Turn 3.417,0.656 4.083,0.865 0.667,0.208 10 false Hall IC 1 5.938,0.656 6.531,0.854 0.594,0.198 10 false Hall IC 1 3.438,2.927 4.125,3.125 0.688,0.198 10 false Hall IC 2 5.948,2.906 6.563,3.094 0.615,0.188 10 false Hall IC 2 1.094,1.698 1.365,1.948 0.271,0.25 10 false N 1.896,1.698 2.167,1.948 0.271,0.25 10 false N 0.698,1.698 0.969,1.948 0.271,0.25 10 false S 1.5,1.698 1.771,1.948 0.271,0.25 10 false S 3.885,1.698 4.156,1.948 0.271,0.25 10 false N 4.677,1.698 4.948,1.948 0.271,0.25 10 false N 5.49,1.698 5.76,1.948 0.271,0.25 10 false N 4.281,1.698 4.552,1.948 0.271,0.25 10 false S 5.094,1.698 5.365,1.948 0.271,0.25 10 false S 0.813,3.469 3.281,3.708 2.469,0.24 10 false Torque Sensor Output Characteristics




FAIL-SAFE


a.

If the power steering ECU assembly detects a malfunction in the EPS system, the power steering ECU assembly illuminates the EPS warning light and sounds the buzzer to inform the driver.


b.

If a system malfunction is detected, the power steering ECU assembly changes control mode to fail-safe mode. For details, refer to the Repair Manual.



DIAGNOSIS


a.

The power steering ECU assembly will also store a Diagnostic Trouble Code (DTC). The DTC can be accessed through the use of an intelligent tester. For details, refer to the Repair Manual.