Home › Power Source / Network › NETWORKING › MULTIPLEX COMMUNICATION SYSTEM › 2011.12–2014.12
NM2170E _57 Power Source / Network _056983 NETWORKING _0277779 MULTIPLEX COMMUNICATION SYSTEM UN GENERAL/CONTROL/DETAILS F

NETWORKING  MULTIPLEX COMMUNICATION SYSTEM  GENERAL/CONTROL/DETAILS  GENERAL  


OUTLINE


a.

The multiplex communication system uses the 2 communication protocols (CAN and LIN) to achieve a streamlined wiring harness configuration.

Protocol Outline
CAN (Controller Area Network) The HS (High Speed)-CAN is used for the power train, chassis and body electrical systems. The HS-CAN consists of the V bus and the sub bus 15. The power management control ECU with gateway function is used to transmit data between the buses.
LIN (Local Interconnect Network) LIN is used for local area networking, in which the system has a respective bus for each body electrical system.


b.

There is no direct communication between CAN and LIN networks because these multiplex communication systems are incompatible. CAN and LIN are separate networks. Because these are separate networks, some ECUs serve as gateways for the transfer of data, allowing communication between CAN and LIN networks.



MAIN FEATURES


a.

Multiplex Communication

i.

Generally speaking, multiplex communication refers to the use of serial communication data that consists of bits and frames in order to exchange information among various ECUs. This allows for a reduction of the amount of wiring on the vehicle. A bit is the basic unit of communication that is used to represent the information. A bit is represented by binary values of "0" or "1".For CAN communication, a differential voltage drive is used to represent the binary values of "0" or "1". This "differential voltage drive" reduces the effects of electrical interference.

U135264E04
0.094,0.125 1.792,0.469 1.698,0.344 12 false Conceptual Drawing: 0.083,0.771 1.854,1 1.771,0.229 10 false Serial Communication Data 2.042,0.677 2.208,0.917 0.167,0.24 10 false 1 2.042,1.115 2.198,1.323 0.156,0.208 10 false 0 2.542,1.417 3.063,1.698 0.521,0.281 10 false Header 3.76,0.802 4.125,1.104 0.365,0.302 10 false Data 5.219,1.406 6.167,1.656 0.948,0.25 10 false End Message 3.688,1.969 4.188,2.25 0.5,0.281 10 false Frame 0.677,3.458 1.24,3.708 0.563,0.25 10 false Battery 2.063,4.25 2.573,4.458 0.51,0.208 10 false Switch 2.771,3.354 3.146,3.583 0.375,0.229 10 false ECU 3.313,2.906 3.594,3.125 0.281,0.219 10 false On 3.292,3.313 3.552,3.521 0.26,0.208 10 false Off 4.802,3.354 5.198,3.552 0.396,0.198 10 false ECU 6.448,2.823 6.906,3.021 0.458,0.198 10 false Light 6.448,3.24 6.917,3.427 0.469,0.188 10 false Motor 6.448,3.656 6.958,3.865 0.51,0.208 10 false Heater 6.448,4.083 7.042,4.292 0.594,0.208 10 false Solenoid



b.

Differences between CAN and LIN

i.

The protocols, which are the rules for establishing data communication, differ between the CAN and LIN. If the ECUs in the networks use different frameworks for their data, such as communication speed, communication wire, and signals, they will be unable to understand each other. Therefore, protocols (rules) must be established among them.


ii.

Compared to the LIN, the CAN features high-speed data transmission. Therefore, the CAN is able to transmit larger amounts of data faster than other protocols. This feature makes it possible to transmit data accurately for the power train, chassis and body electrical systems, which requires large amounts of data to be transmitted in short periods of time.

Protocol CAN LIN
Communication Speed 500 kbps* 9.6 kbps*
Communication Wire Twisted-pair Wire AV Single Wire
Drive Type Differential Voltage Drive Single Wire Voltage Drive
Data Length 1-8 Byte (Variable) 2, 4, 8 Byte (Variable)

HINT:

bps*: abbreviation for "Bits Per Second", indicating the number of bits that can be transmitted per second.



iii.

A twisted-pair wire is used for CAN communication. An Automobile Vinyl (AV) single wire is used for LIN communication.

Communication Wire Outline
Twisted-pair Wire
Y120996

This communication wire is a pair of twisted lines Communication is driven by applying different voltages to the two lines in order to send a single signal. This system, which is called a "Differential Voltage Drive", reduces noise.
AV Single Wire
Y120997

This is a lightweight single communication wire that consists of a single core line surrounded by insulation. Voltage is applied to this line in order to drive communication, and this system is called a "Single Wire Voltage Drive".

Y100742E11
0.719,1.302 1.063,1.604 0.344,0.302 10 false ECU 2.729,1.281 3.073,1.583 0.344,0.302 10 false ECU 1.375,1.438 2.365,1.802 0.99,0.365 10 false AV Single Wire 1.083,2.167 2.708,2.5 1.625,0.333 10 false Single Wire Voltage Drive 4.052,1.333 4.396,1.635 0.344,0.302 10 false ECU 6.135,1.281 6.479,1.583 0.344,0.302 10 false ECU 4.708,1.531 5.844,1.844 1.135,0.313 10 false Twisted-pair Wire 4.469,2.167 6.083,2.5 1.615,0.333 10 false Differential Voltage Drive