Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BODY STRUCTURE › 2011.12–2014.12
NM2170E _59 Vehicle Exterior _056996 EXTERIOR PANELS / TRIM _0277796 BODY STRUCTURE UN GENERAL/CONTROL/DETAILS F

EXTERIOR PANELS / TRIM  BODY STRUCTURE  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION


a.

Impact Absorbing Structure for Frontal Collision

i.

A body structure ensures efficient impact energy absorption and dissipation by the frames from the front to under body to soften the impact to the passengers and minimizes cabin deformation by the rigid cabin frames, in the event of a frontal collision.


ii.

Impact energy during a frontal collision will first be dispersed into the left and right front side members by the front bumper reinforcement. Then it will be dispersed again into the rocker reinforcements and under frames via the front torque boxes.


iii.

Impact energy from the upper members will be dispersed into the front door beltline reinforcements and front pillar reinforcement sub-assembly via the Minimum Intrusion Cabin System (MICS) bulks and then distributed to the roof side rail sub-assembly.

Y118380E02
3.948,5.448 4.521,4.781 4.521,4.781 4.844,4.781 true 4.292,1.573 4.865,0.552 4.865,0.552 5.188,0.552 true 4.344,2.219 4.917,3.198 4.917,3.198 5.229,3.198 true 4.281,3.052 4.615,3.646 4.615,3.646 4.802,3.646 true 3.25,3.24 3.583,3.833 3.583,3.833 3.771,3.833 true 2.823,3.083 2.531,3.823 2.531,3.823 2.365,3.823 true 1.927,3.146 1.635,3.771 1.635,3.771 1.469,3.771 true 1.917,2.198 1.469,2.354 1.469,2.354 1.208,2.354 true 3.156,1.313 2.958,0.854 2.958,0.854 2.844,0.854 true 1.667,1.115 1.458,0.667 1.458,0.667 1.344,0.667 true 2.271,5.792 1.896,6.479 1.896,6.479 1.677,6.479 true 4.865,4.688 5.188,4.927 0.323,0.24 10 false *10 1.521,6.406 1.729,6.594 0.208,0.188 10 false *8 1.177,0.583 1.354,0.771 0.177,0.188 10 false *9 1.052,2.271 1.281,2.479 0.229,0.208 10 false *2 1.313,3.698 1.521,3.885 0.208,0.188 10 false *1 2.198,3.74 2.417,3.938 0.219,0.198 10 false *8 3.792,3.75 4.031,3.938 0.24,0.188 10 false *7 4.823,3.552 5.042,3.729 0.219,0.177 10 false *6 5.26,3.104 5.469,3.313 0.208,0.208 10 false *5 2.688,0.781 2.896,0.948 0.208,0.167 10 false *3 5.208,0.458 5.406,0.667 0.198,0.208 10 false *4

Text in Illustration
*1 Front Bumper Reinforcement *2 Upper Member
*3 Front Pillar Reinforcement Sub-assembly *4 Roof Side Rail Sub-assembly
*5 Front Door Beltline Reinforcement *6 Rocker Reinforce Sub-assembly
*7 Front Torque Box *8 Front Side Member
*9 Minimum Intrusion Cabin System *10 Front Panel Member Sub-assembly
V100135

Path of Collision Energy
V100136

Frontal Collision


iv.

Dash panel insulator pads are provided in the lower section of the dash panel to lessen the impact to the legs of the front passengers.

Y117526E03
4.052,1.969 4.552,0.781 4.552,0.781 4.76,0.781 true 2.5,2.365 1.885,2.063 1.885,2.063 1.646,2.063 true 3.531,1.198 3.969,0.365 3.969,0.365 4.177,0.365 true 2.979,2.448 2.74,3.115 2.74,3.115 2.51,3.115 true 4.781,0.688 5.063,0.875 0.281,0.188 10 false *4 1.469,1.979 1.698,2.167 0.229,0.188 10 false *1 4.198,0.26 4.479,0.448 0.281,0.188 10 false *3 2.344,3.031 2.625,3.219 0.281,0.188 10 false *2

Text in Illustration
*1 Foot Rest Area (No. 3 Dash Panel Insulator Pad) *2 Accelerator Pedal Area (No. 2 Dash Panel Insulator Pad)
*3 Dash Panel *4 Passenger Seat (No. 4 Dash Panel Insulator Pad)
V100135

Front - -


v.

When the engine is moved toward the cabin due to collision, the brake booster (with master cylinder) will be pushed inward, causing the brake pedal support sub-assembly to detach from the bolt fastening the instrument panel reinforcement, and it will allow the brake pedal support sub-assembly to slide backward along with the bottom of the guide plate. As a result, the brake pedal will move down and forward.

Y118377E03
1.656,1.438 1.521,1.01 1.521,1.01 1.292,1.01 true 2.219,1.271 2.396,0.792 2.396,0.792 2.563,0.792 true 3.021,1.292 3.292,1.625 3.292,1.625 3.458,1.625 true 2.573,2.052 2.844,2.385 2.844,2.385 3.01,2.385 true 4.177,3.646 4.365,3.167 4.365,3.167 4.521,3.167 true 4.313,4.042 4.573,4.365 4.573,4.365 4.74,4.365 true 3.948,5.792 4.125,5.313 4.125,5.313 4.292,5.313 true 3.448,3.927 3.271,3.448 3.271,3.448 3.104,3.448 true 2.688,4.469 2.51,4.948 2.51,4.948 2.344,4.948 true 2.917,5.688 2.74,6.167 2.74,6.167 2.573,6.167 true 1.104,0.927 1.333,1.115 0.229,0.188 10 false *1 2.594,0.698 2.875,0.885 0.281,0.188 10 false *2 3.5,1.531 3.781,1.719 0.281,0.188 10 false *3 3.031,2.281 3.313,2.469 0.281,0.188 10 false *4 4.563,3.073 4.844,3.26 0.281,0.188 10 false *2 4.76,4.271 5.042,4.458 0.281,0.188 10 false *4 4.323,5.219 4.604,5.406 0.281,0.188 10 false *7 2.938,3.375 3.219,3.563 0.281,0.188 10 false *1 2.177,4.865 2.458,5.052 0.281,0.188 10 false *5 2.406,6.083 2.688,6.271 0.281,0.188 10 false *6

Text in Illustration
*1 Brake Pedal Support Sub-assembly *2 Bolt
*3 Instrument Panel Reinforcement *4 Guide Plate
*5 Brake Booster (with Master Cylinder) *6 Dash Panel
*7 Brake Pedal Sub-assembly -
V100135

Slide Backward
V100136

Frontal Collision
V100144

During a collision - -



b.

Impact Absorbing Structure for Side Collision

i.

Framework components such as reinforcements have been strengthened and optimally allocated around the door openings to optimize dispersal of impact energy in the event of a side collision.


ii.

Ultra high-strength sheet steel is used for the rocker outer reinforcements, center pillar reinforcements, center pillar hinge reinforcements, and high-strength sheet steel is used for the center pillar inner reinforcements, rail outer reinforcements and roof reinforcements to ensure bearing force.


iii.

Bulkheads are placed inside the rocker reinforcements to efficiently transmit impact energy to the front floor cross members as well as preventing the rocker reinforcement deformation.


iv.

Optimal placement of the front and rear door side impact protection beams enables a construction that efficiently transmits load.

Y118169E02
1.323,6.594 1.063,7.063 1.063,7.063 0.833,7.063 true 2.427,6.875 2.677,7.302 2.677,7.302 2.917,7.302 true 4.031,4.229 3.802,4.646 3.802,4.646 3.552,4.646 true 3.292,3.792 3.479,3.26 3.479,3.26 3.677,3.26 true 4.875,2.271 5.427,2.917 5.427,2.917 5.677,2.917 true 3.979,2.656 4.656,3.333 4.656,3.333 4.896,3.333 true 3.792,1.406 3.396,0.729 3.396,0.729 3.167,0.729 true 3.667,0.906 4.042,0.302 4.042,0.302 4.188,0.302 true 3.469,2.469 2.927,2.958 2.927,2.958 2.698,2.958 true 0.656,6.99 0.938,7.177 0.281,0.188 10 false *8 2.938,7.208 3.219,7.396 0.281,0.188 10 false *9 0.521,5.604 0.708,5.792 0.188,0.188 10 false *a 3.385,4.563 3.667,4.75 0.281,0.188 10 false *6 3.708,3.156 3.99,3.344 0.281,0.188 10 false *7 5.708,2.823 5.99,3.01 0.281,0.188 10 false *3 4.917,3.229 5.198,3.417 0.281,0.188 10 false *4 4.385,1.365 4.521,1.552 0.135,0.188 10 true A 4.063,1.448 4.198,1.635 0.135,0.188 10 true A 3,0.646 3.208,0.833 0.208,0.188 10 false *1 4.208,0.219 4.427,0.396 0.219,0.177 10 false *2 2.521,2.875 2.75,3.063 0.229,0.188 10 false *5

Text in Illustration
*1 Roof Side Rail Sub-assembly *2 Roof Panel Reinforcement
*3 Rear Door Side Impact Protection Beam *4 Rocker Reinforce Sub-assembly
*5 Front Door Side Impact Protection Beam *6 Bulkhead
*7 Floor Cross Member *8 Center Body Pillar Outer Reinforcement
*9 Center Body Pillar Upper Hinge Reinforcement - -
*a A-A Cross Section - -
V100135

Path of Collision Energy
V100136

Side Collision


v.

An impact absorbing pad (front door trim pad) is installed on the inside of the front door to soften the impact to the hip area of the front passenger. In addition, an impact absorbing pad (door trim lower pad) to soften the impact to the hip area of the rear passenger are installed on the inside of the rear door.

Y118700E02
2.438,1.219 2.729,0.375 2.729,0.375 2.927,0.375 true 5.219,1.083 5.427,0.448 5.427,0.448 5.635,0.448 true 5.333,2.427 5.719,3.208 5.719,3.208 5.958,3.208 true 2.958,2.563 3.323,3.354 3.323,3.354 3.563,3.354 true 2.958,0.271 3.24,0.458 0.281,0.188 10 false *1 5.677,0.354 5.958,0.542 0.281,0.188 10 false *3 5.979,3.125 6.26,3.313 0.281,0.188 10 false *4 3.583,3.26 3.865,3.448 0.281,0.188 10 false *2

Text in Illustration
*1 Front Door Trim Board Sub-assembly *2 Impact Absorbing Pad
*3 Rear Door Trim Board Sub-assembly *4 Impact Absorbing Pad


vi.

Impact absorbing structure is used in consideration of an occupant's head impacting a pillar or the roof side in reaction to a collision.


vii.

Impact energy to the occupant's head will be reduced by the deformation of the ribbed section designed for impact absorption and hard urethane, provided inside the pillar garnish and roof headlining.

Y117532E02
1.76,0.833 1.896,1.021 0.135,0.188 10 false A 1.906,1.292 2.042,1.479 0.135,0.188 10 false A 3.542,0.656 3.677,0.844 0.135,0.188 10 false B 5.969,0.844 6.104,1.031 0.135,0.188 10 false C 5.969,1.344 6.104,1.531 0.135,0.188 10 false C 3.5,1.073 3.635,1.26 0.135,0.188 10 true B 3.021,1.448 3.156,1.635 0.135,0.188 10 false D 0.396,3.281 0.583,3.469 0.188,0.188 10 false *a 2.708,3.302 2.896,3.49 0.188,0.188 10 false *b 4.979,3.281 5.167,3.469 0.188,0.188 10 false *c 1.917,6.063 2.104,6.25 0.188,0.188 10 false *d 3.604,1.438 3.74,1.625 0.135,0.188 10 false D

Text in Illustration
*a A-A Cross Section *b B-B Cross Section
*c C-C Cross Section *d D-D Cross Section
V100144

Impact Absorbing Material - -



c.

Impact Absorbing Structure for Roof Collision

i.

The frames have been strengthened to minimize the deformation of the cabin when a load is applied to the vehicle in the event of the vehicle roll over.


ii.

An inner reinforcement is provided at the corner of the inner front pillar to minimize the deformation of the front pillar.


iii.

A roof upper reinforcement has been provided in addition to a roof reinforcement to ensure rigidity and minimize deformation of the cabin.


iv.

The thicknesses of the front head and header extensions have been optimized to minimize deformation of the windshield frame.

Y117530E03
2.646,0.854 3.177,0.385 3.177,0.385 3.344,0.385 true 2.063,1.021 1.896,0.75 1.896,0.75 1.667,0.75 true 2.604,1.313 1.604,1.01 1.604,1.01 1.375,1.01 true 5.906,4.063 6.083,3.583 6.083,3.583 6.25,3.583 true 4.885,4.521 4.656,4.938 4.656,4.938 4.406,4.938 true 1.917,4.094 1.625,3.542 1.625,3.542 1.396,3.542 true 3.375,0.292 3.656,0.479 0.281,0.188 10 false *3 3.052,0.99 3.188,1.156 0.135,0.167 10 true A 2.76,1.063 2.896,1.25 0.135,0.188 10 true A 1.5,0.667 1.688,0.854 0.188,0.188 10 false *1 1.208,0.917 1.396,1.104 0.188,0.188 10 false *2 1.229,3.469 1.458,3.656 0.229,0.188 10 false *4 6.271,3.49 6.552,3.677 0.281,0.188 10 false *6 4.25,4.844 4.531,5.031 0.281,0.188 10 false *5 4.042,3.438 4.229,3.625 0.188,0.188 10 false *a

Text in Illustration
*1 Windshield Header Panel Inner *2 No. 2 Front Body Pillar Reinforcement Upper Out
*3 Center Roof Panel Reinforcement *4 Front Body Pillar Lower Inner
*5 Roof Panel Center Reinforcement *6 Roof Panel Center Reinforcement Upper
*a A-A Cross Section - -
V100135

Path of Collision Energy
V100136

Impact



d.

Lessening Pedestrian Injury

i.

An energy absorber is provided at the front of the front bumper reinforcement to dampen the impact to the legs in the event of a collision with a pedestrian.

Y118170E02
5.688,2.24 6.219,1.76 6.219,1.76 6.385,1.76 true 5.198,2.344 4.813,1.604 4.813,1.604 4.583,1.604 true 5.313,3.219 4.854,2.969 4.854,2.969 4.615,2.969 true 5.094,3.781 4.885,4.146 4.885,4.146 4.646,4.146 true 5.708,3.719 5.458,4.313 5.458,4.313 5.219,4.313 true 1.24,1.896 1.375,2.083 0.135,0.188 10 false A 1.24,3.49 1.406,3.677 0.167,0.188 10 false A 6.406,1.667 6.688,1.854 0.281,0.188 10 false *3 4.406,1.521 4.583,1.708 0.177,0.188 10 false *1 4.438,2.896 4.615,3.083 0.177,0.188 10 false *2 4.479,4.073 4.76,4.26 0.281,0.188 10 false *4 5.042,4.24 5.323,4.427 0.281,0.188 10 false *5 4.406,0.323 4.594,0.51 0.188,0.188 10 false *a

Text in Illustration
*1 Front Bumper Energy Absorber *2 Lower Grille
*3 Front Bumper Reinforcement *4 Front Bumper Cover
*5 Front Lower Bumper Absorber - -
*a A-A Cross Section - -


ii.

A vertical ribbed structure is used on the hood inner panel in order to allow the hood to collapse easily, so that a collision impact can be reduced by using the whole part of the hood.


iii.

Ridges are provided in appropriate positions of the hood inner panel and hood reinforcement respectively, in order to lessen the impact energy to a pedestrian during a collision by allowing both structures to collapse and to absorb the impact energy.

Y117534E03
6.115,1.948 6.281,2.5 6.281,2.5 6.104,2.5 true 6.521,2.104 6.281,2.5 true 5.271,2.531 4.99,1.958 4.99,1.958 4.802,1.958 true 5.375,2.354 4.99,1.958 true 1.604,1.469 1.958,1.063 1.958,1.063 2.198,1.063 true 1.219,2.583 0.958,3.031 0.958,3.031 0.781,3.031 true 1.135,1.688 0.865,0.552 0.865,0.552 0.688,0.552 true 1.979,2.125 0.865,0.552 0.865,0.552 1.552,1.896 true 3.563,0.396 3.729,0.552 0.167,0.156 10 false *b 2.219,0.979 2.458,1.156 0.24,0.177 10 false *2 0.615,2.969 0.781,3.125 0.167,0.156 10 false *1 0.375,2.417 0.49,2.573 0.115,0.156 10 false A 1.198,1.781 1.313,1.938 0.115,0.156 10 false A 0.521,0.448 0.688,0.604 0.167,0.156 10 false *a 4.833,0.51 5.094,0.708 0.26,0.198 10 false :*c 5.948,2.417 6.167,2.604 0.219,0.188 10 false *2 4.635,1.875 4.844,2.063 0.208,0.188 10 false *1

Text in Illustration
*1 Hood Reinforcement *2 Hood Inner Panel
*a Vertical Ribbed Structure *b A-A Cross Section
*c Ridges - -
V100135

Impact - -


iv.

In the front fender installation areas, a crushable impact absorbing bracket (front apron to cowl side member plate) has been provided so as to lessen the impact to a pedestrian in the event of a collision.

Y117535E03
1.229,1.552 1.042,1.177 1.042,1.177 0.813,1.177 true 2,0.917 2.24,0.365 2.24,0.365 2.406,0.365 true 5.323,2.188 4.656,1.385 4.656,1.385 4.427,1.385 true 5.333,1.865 4.667,1.385 true 5.865,1.469 6.25,0.896 6.25,0.896 6.479,0.896 true 5.594,1.229 6.24,0.896 true 0.625,1.083 0.854,1.271 0.229,0.188 10 false *2 2.448,0.281 2.729,0.469 0.281,0.188 10 false *1 4.24,1.302 4.469,1.49 0.229,0.188 10 false *2 6.5,0.802 6.729,0.99 0.229,0.188 10 false *1 3.833,0.365 4.021,0.552 0.188,0.188 10 false *a 1.635,1.396 1.771,1.583 0.135,0.188 10 true A 0.969,1.771 1.104,1.958 0.135,0.188 10 false A

Text in Illustration
*1 Front Fender Panel (Front Fender Sub-assembly) *2 Impact Absorbing Bracket (Front Apron to Cowl Side Member Plate)
*a A-A Cross Section - -
V100135

Impact - -


v.

In order to reduce the impact applied from above, the cowl employs a crushable structure with collapsible ridges that are considerably arranged.


vi.

The easily collapsible cowl louver has been provided so that it can collapse if an impact force will occur from above, reducing the impact energy.

Y117536E02
3.781,3.74 3.646,3.948 3.646,3.948 3.521,3.948 true 3.833,4.438 3.938,4.625 3.938,4.625 4.094,4.625 true 1.802,6.094 1.438,5.51 1.438,5.51 1.156,5.51 true 1.438,6.25 1.438,5.51 true 2.74,5.958 3.083,5.385 3.083,5.385 3.365,5.385 true 3.083,6.135 3.083,5.385 true 4.625,6.625 5.906,6.396 5.906,6.396 6.198,6.396 true 4.5,6.073 5.885,6.396 true 3.271,1.552 3.458,1.719 0.188,0.167 10 false A 3.823,1.198 3.979,1.385 0.156,0.188 10 false A 3.344,3.865 3.531,4.094 0.188,0.229 10 false *b 4.104,4.531 4.375,4.74 0.271,0.208 10 false *4 4.979,4.76 5.281,4.948 0.302,0.188 10 false : *c 0.99,5.427 1.188,5.615 0.198,0.188 10 false *1 3.385,5.292 3.635,5.5 0.25,0.208 10 false *2 6.229,6.302 6.5,6.51 0.271,0.208 10 false *3 0.354,2.875 0.594,3.104 0.24,0.229 10 false *a

Text in Illustration
*1 Hood Panel *2 No.1 Cowl Top Ventilator Louver Center
*3 Cowl Louver *4 Cowl Top Panel Inner
*a A-A Cross Section *b Open Section Structure
*c Ridges - -
V100135

Impact - -



e.

Aerodynamics

i.

In order to reduce the air that flows to the area behind the vehicle, all the surfaces of the upper body have been made flush, also the vehicle height has been lowered to reduce the frontal projected area, the roof rear end angle has been optimally adjusted, and an aero corner (squared corner edge) has been provided on the rear bumper side ends. Furthermore, the side body surfaces have been trimmed to reduce drag, delivering excellent aerodynamics.

U183765E02
4,0.969 4.24,0.323 4.24,0.323 4.521,0.323 true 4.427,1.99 4.948,3.313 4.948,3.313 5.292,3.313 true 5.74,4.948 5.99,4.292 5.99,4.292 6.271,4.292 true 5.177,7.135 5.396,7.521 5.396,7.521 5.542,7.521 true 4.552,0.229 4.802,0.427 0.25,0.198 10 false *a 5.292,3.219 5.531,3.417 0.24,0.198 10 false *b 6.292,4.198 6.51,4.385 0.219,0.188 10 false *c 5.573,7.417 5.833,7.604 0.26,0.188 10 false *d

Text in Illustration
*a Frontal Projected Area Reduction *b Reduction of Air Resistance by Narrowing the Flat Surface Area
*c Optimum Length and Angle of Rear Spoiler *d Sharp Corner Edge at the Side or Rear Bumper Cover


ii.

The pagoda roof, a curved surface roof top, is used to reduce the frontal projected area so as to reduce wind drag while driving, improving the fuel efficiency.


iii.

Along with the flush upper body surfaces, fins that route air flowing over the body surfaces have been provided on the outer rear view mirror assembly and rear combination light assembly to minimize air turbulence, reducing wind drag. As a result, improvement in the efficient fuel consumption has been achieved.


iv.

Through use of airflow routing components that control air flowing over the under body surface, the design delivers excellent aerodynamics, offering comfortable stability when the vehicle is driven straight at high speeds and good maneuvering stability.

Y118378E02
2.354,0.781 2.563,0.469 2.563,0.469 2.729,0.469 true 1.75,0.813 1.563,1.188 1.563,1.188 1.333,1.188 true 6.156,1.563 6.354,1.25 6.354,1.25 6.521,1.25 true 6.594,2.146 6.771,1.833 6.771,1.833 6.844,1.833 true 6.698,2.385 6.802,2.219 6.802,2.219 6.844,2.219 true 4.052,3.094 3.646,2.594 3.646,2.594 3.417,2.594 true 3.896,3.167 3.417,2.875 3.417,2.875 3.188,2.875 true 1.563,4.396 1.969,3.771 1.969,3.771 2.198,3.771 true 4.865,4.219 5.125,3.833 5.125,3.833 5.354,3.833 true 4.813,6.135 5.073,6.521 5.073,6.521 5.302,6.521 true 1.573,5.938 1.896,6.573 1.896,6.573 2.125,6.573 true 6.052,4.938 6.302,4.552 6.302,4.552 6.531,4.552 true 2.76,0.365 3.042,0.552 0.281,0.188 10 false *c 1.167,1.115 1.396,1.302 0.229,0.188 10 false *b 5.146,2.25 5.281,2.438 0.135,0.188 10 true A 3.781,1.448 3.917,1.635 0.135,0.188 10 false A 6.552,1.167 6.833,1.354 0.281,0.188 10 false *1 6.875,1.719 7.115,1.917 0.24,0.198 10 false *d 6.875,2.135 7.083,2.323 0.208,0.188 10 false *3 3.26,2.51 3.458,2.698 0.198,0.188 10 false *2 3.031,2.781 3.229,2.969 0.198,0.188 10 false *d 2.219,3.688 2.417,3.875 0.198,0.188 10 false *4 5.385,3.74 5.583,3.927 0.198,0.188 10 false *6 5.323,6.427 5.594,6.615 0.271,0.188 10 false *7 2.146,6.479 2.417,6.667 0.271,0.188 10 false *5 6.552,4.458 6.781,4.646 0.229,0.188 10 false *8 0.313,0.24 0.5,0.427 0.188,0.188 10 false *a

Text in Illustration
*1 Rear Spoiler *2 Outer Rear View Mirror Assembly
*3 Rear Combination Light Assembly *4 Front Spat LH (Front Wheel Opening Extension Pad LH)
*5 Front Spat RH (Front Wheel Opening Extension Pad RH) *6 Rear Spat LH (Rear Wheel Opening Extension Pad LH)
*7 Rear Spat RH (Rear Wheel Opening Extension Pad RH) *8 No. 1 Floor Under Cover
*a A-A Cross Section *b Pagoda Roof
*c General Roof *d Fin


v.

A rear spoiler has been provided at the roof end for all models to prevent air, which flows from the roof, from entering the area behind the vehicle, reducing wind drag and resulting in improvement in fuel efficiency. As for the style of the rear spoiler, it is shaped so that the body line can seamlessly extend from the roof panel.


vi.

In accordance with the model specifications, a large rear spoiler has been made available as an option. The large rear spoiler has openings and is a wing-shaped structure, thus, air that flows over the wing-shaped spoiler surface will produce down force, ensuring the maneuvering stability further.

Y118167E03
5.688,2.052 6.063,2.49 6.063,2.49 6.292,2.49 true 4.885,4.813 5.271,5.25 5.271,5.25 5.5,5.25 true 5.635,4.26 5.885,3.719 5.885,3.719 6.115,3.719 true 3.458,0.323 3.646,0.51 0.188,0.188 10 false *a 3.5,3.188 3.688,3.375 0.188,0.188 10 false *b 6.313,2.385 6.833,2.594 0.521,0.208 10 false *1 (*A) 2.469,0.979 2.604,1.167 0.135,0.188 10 true A 1.698,1.083 1.854,1.26 0.156,0.177 10 true A 2.854,3.917 2.99,4.104 0.135,0.188 10 false B 1.927,4.063 2.063,4.25 0.135,0.188 10 true B 5.531,5.146 6.052,5.365 0.521,0.219 10 false *1 (*B) 6.146,3.615 6.635,3.844 0.49,0.229 10 false *1 (*B) 5.917,4.313 6.104,4.5 0.188,0.188 10 false *c

Text in Illustration
*A Standard Type *B Large Type
*1 Rear Spoiler - -
*a A-A Cross Section *b B-B Cross Section
*c Down Force - -
V100135

Airflow - -


vii.

The front and rear spats block air flowing toward the tires, reducing air that flows into the wheel houses. Reducing the air will minimize interference with airflow generated by tire revolution. By minimizing air turbulence that occurs around the tires, the maneuvering stability has been ensured.

Y118168E02
1.99,1.385 2.167,1.802 2.167,1.802 2.396,1.802 true 4.771,1.385 4.948,1.802 4.948,1.802 5.177,1.802 true 2.427,1.708 2.656,1.896 0.229,0.188 10 false *1 5.208,1.698 5.438,1.885 0.229,0.188 10 false *2 0.781,2 1.01,2.188 0.229,0.188 10 false *a 1.667,1.698 1.802,1.885 0.135,0.188 10 false B

Text in Illustration
*1 Front Spat (Front Wheel Opening Extension Pad) *2 Rear Spat (Rear Wheel Opening Extension Pad)
*a View from B - -
V100135

Airflow - -


viii.

A floor under cover has been provided on the rear bumper cover to regulate air that flows over the bottom surface of the rear bumper cover, reducing wind drag and resulting in the improvement in efficient fuel consumption. Furthermore, by adding the fin, the maneuvering stability has also been enhanced.

Y117541E04
2.042,1.729 2.417,2.167 2.417,2.167 2.646,2.167 true 4.677,0.917 4.531,0.615 4.531,0.615 4.302,0.615 true 3.948,1.01 3.813,0.698 3.813,0.698 3.583,0.698 true 1.469,2.063 1.604,2.25 0.135,0.188 10 false A 1.458,1.458 1.594,1.646 0.135,0.188 10 true A 2.677,2.073 2.906,2.26 0.229,0.188 10 false *1 2.823,0.26 3.01,0.448 0.188,0.188 10 false *a 5.313,0.313 5.5,0.5 0.188,0.188 10 false *b 4.125,0.531 4.354,0.719 0.229,0.188 10 false *1 3.396,0.615 3.625,0.802 0.229,0.188 10 false *2 1.281,2.344 1.417,2.531 0.135,0.188 10 false B

Text in Illustration
*1 Rear Bumper Cover *2 No. 1 Floor Under Cover
*a A-A Cross Section *b View from B
V100135

Airflow - -




CONSTRUCTION


a.

Lightweight and Highly Rigid Body

i.

High strength steel sheet and ultra high strength steel sheet are used in order to achieve excellent body rigidity and a lightweight body.

Y117544

Text in Illustration
V100145

High Strength Steel Sheet
V100144

Ultra High Strength Steel Sheet



b.

Body Shell Construction

i.

The radiator support sub-assembly configuration has been further optimized to ensure the impact durability while weight reduction is achieved. In addition, by integrating the crush box and front side member for left and right, further lightweight has been made successfully.

Y117545E02
3.146,2.813 3.521,3.25 3.521,3.25 3.75,3.25 true 3.854,2.625 4.229,3.052 4.229,3.052 4.458,3.052 true 2.396,3.042 2.01,3.479 2.01,3.479 1.781,3.479 true 3.771,3.156 4,3.344 0.229,0.188 10 false *2 4.49,2.958 4.719,3.146 0.229,0.188 10 false *3 1.615,3.385 1.844,3.573 0.229,0.188 10 false *1

Text in Illustration
*1 Radiator Support Sub-assembly *2 Crash Box (Front Side Member Bracket Sub-assembly)
*3 Front Side Member - -


ii.

The outer cowl top panel sub-assembly, which connects the left and right front suspensions, has been reshaped to ensure the body rigidity of the front suspension installation areas and cowl top area.

Y117546E02
5.406,2.573 5.729,3.198 5.729,3.198 5.958,3.198 true 6,3.094 6.229,3.281 0.229,0.188 10 false *1

Text in Illustration
*1 Outer Cowl Top Panel Sub-assembly - -
V100135

Front - -


iii.

The rear absorber plates have been provided in the areas where the left and right rear suspensions are mounted so as to ensure the rigidity of the suspension installation areas.


iv.

The back door opening has been strengthened with reinforcements to ensure the rigidity against body torsion.


v.

The spot welding positions for the corner areas of the front door, rear door and back door openings have been optimized to ensure body rigidity.

Y117547E02
6.188,1.302 6.479,0.906 6.479,0.906 6.646,0.906 true 4.979,1.135 4.542,0.563 4.542,0.563 4.375,0.563 true 5.521,3.271 5.854,3.906 5.854,3.906 6.083,3.906 true 4.302,3.01 3.719,3.771 3.719,3.771 3.49,3.771 true 1.594,1.479 2.01,0.688 2.01,0.688 2.177,0.688 true 1.635,3.469 1.969,4.094 1.969,4.094 2.198,4.094 true 6.688,0.813 6.969,1 0.281,0.188 10 false *4 4.198,0.479 4.479,0.667 0.281,0.188 10 false *3 6.115,3.802 6.385,3.99 0.271,0.188 10 false *6 3.313,3.698 3.583,3.885 0.271,0.188 10 false *5 2.208,0.594 2.49,0.781 0.281,0.188 10 false *1 2.219,4 2.49,4.188 0.271,0.188 10 false *2

Text in Illustration
*1 Roof Side Outer Reinforcement *2 Rear Absorber Plate
*3 Back Door Upper Reinforcement *4 Back Door Side Reinforcement
*5 Back Door Side Reinforcement *6 Back Door Lower Reinforcement


vi.

The shape of the front portion of the rear floor cross member has been made straight to ensure the rigidity, ensuring the maneuvering stability.


vii.

The braces, which are used to fasten the center cross member, have been provided on the rear floor side members to increase the rigidity, ensuring the maneuvering stability.


viii.

The No.1 rear bumper reinforcement has been made of aluminum to reduce the rear end weight and its shape has also been optimized to ensure the connecting rigidity between the left and right rear floor side members, resulting in ensuring of the maneuvering stability.

Y117548E04
2.708,1.042 2.979,0.729 2.979,0.729 3.167,0.729 true 1.99,2.104 2.427,1.563 2.427,1.563 2.615,1.563 true 3.135,2.708 3.438,3.063 3.438,3.063 3.615,3.063 true 5.604,2.469 5.896,2.844 5.896,2.844 6.083,2.844 true 1.458,1.458 1.135,1.01 1.135,1.01 0.958,1.01 true 1.031,2.292 0.573,2.99 0.573,2.99 0.385,2.99 true 1.865,2.573 1.542,3.104 1.542,3.104 1.354,3.104 true 3.188,0.635 3.417,0.823 0.229,0.188 10 false *2 2.635,1.479 2.865,1.667 0.229,0.188 10 false *3 3.646,2.969 3.875,3.156 0.229,0.188 10 false *4 6.125,2.75 6.354,2.938 0.229,0.188 10 false *5 0.792,0.927 1.021,1.115 0.229,0.188 10 false *1 4.385,1.135 4.615,1.323 0.229,0.188 10 false *a 0.229,2.917 0.458,3.104 0.229,0.188 10 false *4 1.198,3.01 1.427,3.198 0.229,0.188 10 false *5

Text in Illustration
*1 Rear Floor Side Member *2 No. 1 Rear Bumper Reinforcement
*3 Rear Axle Beam Assembly *4 Brace
*5 Center Cross Member - -
*a Vehicle Rear View - -


ix.

The structure, which allows the floor under reinforcement to be inserted between the center cross member and the floor panel, is used to increase the body torsion rigidity.

Y117549E05
4.385,5.667 4.688,6.125 4.688,6.125 4.917,6.125 true 3.135,5.781 2.625,5.146 2.625,5.146 2.396,5.146 true 3.49,1.854 2.958,0.385 2.958,0.385 2.729,0.385 true 3,2.167 1.917,1.281 1.917,1.281 1.688,1.281 true 5.552,0.781 5.906,0.219 5.906,0.219 6.135,0.219 true 4.938,6.021 5.208,6.208 0.271,0.188 10 false *2 2.219,5.063 2.49,5.25 0.271,0.188 10 false *1 4.198,1.448 4.333,1.635 0.135,0.188 10 false A 3.677,2.385 3.813,2.563 0.135,0.177 10 true A 2.563,0.302 2.833,0.49 0.271,0.188 10 false *2 1.531,1.188 1.802,1.375 0.271,0.188 10 false *1 6.156,0.125 6.427,0.313 0.271,0.188 10 false *3 0.854,3.563 1.042,3.75 0.188,0.188 10 false *a

Text in Illustration
*1 Floor Under Reinforcement *2 Center Cross Member
*3 Rear Floor Side Member - -
*a A-A Cross Section - -



c.

Anti-corrosion Sheet Steel

i.

Anti-corrosion sheet steel is used as in the following illustration:

Y118160

Text in Illustration
V100144

Anti-corrosion Sheet Steel - -



d.

Wax and Anti-chipping Application

i.

Wax is applied to front end of hood sub-assembly, edge of the door lower portion and fuel filler lid hinge to improve rust-resistant performance.


ii.

To protect the paint from chipping, anti-chipping paint is applied to the rockers and the front end of the hood sub-assembly.

Y118381E02
6.094,3.333 5.99,3.115 5.99,3.115 5.76,3.115 true 5.583,3.042 5.813,3.229 0.229,0.188 10 false *1

Text in Illustration
*1 Fuel Filler Lid Hinge - -
V100155

Wax
V100144

Anti-chipping Paint



e.

Low Vibration and Low Noise Body

i.

A hood insulator is provided in the hood sub-assembly to absorb noise.


ii.

An outer dash panel insulator and outer dash panel insulator No. 2 are installed around the cowl top panel to reduce the amount of noise entering the vehicle cabin from the engine compartment.


iii.

A front fender side panel protector is provided to reduce the amount of noise transmitted from the area between the fender and front pillar to the vehicle cabin.


iv.

Sound absorbing material is used in the front fender liner to reduce road noise during driving.

Y118162E02
1.458,0.875 1.813,0.323 1.813,0.323 2.042,0.323 true 4.469,1.198 4.823,0.646 4.823,0.646 5.063,0.646 true 6.458,3.208 6.104,3.76 6.104,3.76 5.875,3.76 true 5.333,4.708 5.688,5.26 5.688,5.26 5.917,5.26 true 2.083,0.219 2.594,0.438 0.51,0.219 10 false *1 (*A) 5.094,0.552 5.323,0.74 0.229,0.188 10 false *2 5.427,3.667 5.896,3.854 0.469,0.188 10 false *3 (*A) 5.938,5.167 6.417,5.354 0.479,0.188 10 false *4 (*A)

Text in Illustration
*1 Hood Insulator *2 Outer Dash Panel Insulator
*3 Front Fender Side Panel Protector *4 Sound Absorbing Material


v.

To reduce the amount of road noise, engine noise and droning sound that enters the cabin, the floor panel is coated with a vibration damping coat.

Y118379

Text in Illustration
V100144

Spray Type Damping Material Application Area - -


vi.

A sound insulation material is used in the body frame profile, thus reducing the various noises which intrude from the outside of the vehicle to the inside of the cabin.


vii.

Rocker panel moulding is provided on the underside of the rockers, thus reducing the sound of sand and pebbles thrown up from the road.

U183766E02
3.438,1.281 3.573,1.469 0.135,0.188 10 true B 3.708,1.115 3.844,1.302 0.135,0.188 10 true B 3.469,1.552 3.604,1.74 0.135,0.188 10 false A 3.24,1.302 3.375,1.49 0.135,0.188 10 false A 3.917,1.688 4.063,1.854 0.146,0.167 10 true E 4.76,1.875 4.896,2.031 0.135,0.156 10 true F 5.167,2.073 5.302,2.26 0.135,0.188 10 false F 3.219,2.375 3.354,2.563 0.135,0.188 10 true D 3.229,2.802 3.365,2.99 0.135,0.188 10 true D 0.438,3.385 0.625,3.573 0.188,0.188 10 false *a 2.677,3.365 2.865,3.552 0.188,0.188 10 false *b 4.906,3.375 5.094,3.563 0.188,0.188 10 false *c 0.417,5.583 0.604,5.771 0.188,0.188 10 false *d 2.677,5.594 2.865,5.781 0.188,0.188 10 false *e 4.927,5.604 5.115,5.792 0.188,0.188 10 false *f 4.313,1.573 4.458,1.729 0.146,0.156 10 true E 4.823,0.781 4.958,0.969 0.135,0.188 10 true C 5.302,0.708 5.438,0.896 0.135,0.188 10 true C

Text in Illustration
*a A-A Cross Section *b B-B Cross Section
*c C-C Cross Section *d D-D Cross Section
*e E-E Cross Section *f F-F Cross Section
V100145

Polyurethane Form
V100144

Expanded Form
V100143

Polyethylene Sealer - -



f.

Parts with Low Repair Cost

i.

A structure with the front bumper reinforcement installed with bolts is used to improve the ease of repair and replacement.


ii.

In case of a minor collision, the front bumper reinforcement and crush boxes integrated with the front side members efficiently absorb impact energy, thus reducing damage to the body frames.

Y118165E02
4.677,1.958 5.063,2.396 5.063,2.396 5.292,2.396 true 4.313,2.344 4.771,2.906 4.771,2.906 5,2.906 true 2.844,1.573 2.396,1.115 2.396,1.115 2.167,1.115 true 2.74,2.885 2.354,3.323 2.354,3.323 2.125,3.323 true 5.313,2.292 5.542,2.479 0.229,0.188 10 false *4 5.031,2.823 5.26,3.01 0.229,0.188 10 false *3 1.979,1.021 2.208,1.208 0.229,0.188 10 false *1 1.948,3.24 2.177,3.427 0.229,0.188 10 false *2

Text in Illustration
*1 Radiator Support Sub-assembly *2 Front Bumper Reinforcement
*3 Crush Box *4 Front Side Member