Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › 2015.11–2019.07
NM2170E _59 Vehicle Exterior _056998 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0277798 VEHICLE PROXIMITY NOTIFICATION SYSTEM UN GENERAL/CONTROL/DETAILS F

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Item Function
Vehicle Approaching Speaker Controller Controls starting and stopping of operation, sound pitch and volume level based on signals received from the ECU, sensor and switch.
Vehicle Approaching Speaker Assembly Emits warning sounds based on the operation signal received from the vehicle approaching speaker controller.
Vehicle Approaching Speaker Switch Disables the vehicle proximity notification system operation when the switch is turned on.

Combination Meter Assembly

-

Vehicle Proximity Notification OFF Indicator Light



·

Sends a vehicle speed signal to the vehicle approaching speaker controller.

·

The vehicle proximity notification OFF indicator light illuminates when the vehicle proximity notification system has been disabled using the vehicle approaching speaker switch.

·

The vehicle proximity notification OFF indicator light blinks for 16 seconds to inform the driver when the vehicle approaching speaker controller detects a malfunction in the vehicle proximity notification system.


Shift Lock Control Unit Assembly

-

Shift Lock Control ECU

-

P Detection Switch



Sends a signal, when the shift lever is in the P position, to the vehicle approaching speaker controller.
Engine Oil Pressure Switch Assembly Sends an engine running signal to the vehicle approaching speaker controller.
Stop Light Switch Assembly Sends a brake pedal state signal to the vehicle approaching speaker controller.


OPERATING CONDITION


Condition Outline
System Active The vehicle proximity notification system operates (emits a warning sound) when either of the following conditions is met:
·

The vehicle is stationary (0 km/h or mph), the engine is stopped, the vehicle approaching speaker switch is off and stop light switch is turned from on to off, the shift lever is in any position other than P.*

·

The vehicle speed is 25 km/h (16 mph) or less, the engine is stopped and vehicle approaching speaker switch is off.


System Stop The vehicle proximity notification system stops operating when any of the following conditions is met:
·

The engine starts.

·

The vehicle approaching speaker switch is turned on.

·

The vehicle speed is 25 km/h (16 mph) or more.

·

The vehicle is stationary (0 km/h or mph) and the stop light switch on signal is received continuously for more than approximately 0.24 second.

·

The vehicle is stationary (0 km/h or mph) and the P position signal is received continuously for more than approximately 0.24 second.

·

The vehicle is stationary (0 km/h or mph) and the stop light switch off signal is received continuously for more than approximately 3 seconds (e.g. when the vehicle is stopped, and in neutral with the parking brake applied).



HINT:

*: When the system is stopped due to a vehicle speed of 0 km/h (0 mph) and the stop light switch off signal is received continuously for more than approximately 3 seconds, the system operates again when any of the following conditions is met:

-

A vehicle speed signal of 1 km/h (1 mph) or more is received.

-

The brake pedal is operated.





SYSTEM CONTROL


Control Outline
Vehicle Speed Linked Control
·

Emits the warning sound by controlling the pitch of the sound in accordance with vehicle speed.

·

The warning sound becomes higher as the vehicle accelerates and it becomes lower as the vehicle decelerates.


Audibility Enhancing Control When the vehicle proximity notification system is not sounding and the vehicle is stopped (vehicle speed of 0 km/h (0 mph)), if the system operates due to a vehicle speed signal or brake pedal operation (system is changed from being disabled to enabled), the warning sound volume becomes higher than usual for about 1 second to warn people around the vehicle that the vehicle may move.
Fade-in/Fade Out Control When the system starts operating, the warning sound volume gradually increases*, and when system operation is stopped, the sound volume gradually decreases.

HINT:

*: When audibility enhancing control is performed, the system starts operating using this audibility enhancing control.



DIAGNOSIS


a.

The vehicle approaching speaker controller stores a 5-digit Diagnostic Trouble Code (DTC) in its memory. The 5-digit DTCs can be read after connecting the Global TechStream (GTS) to the DLC3.


b.

For details, refer to the respective Repair Manual.