FUNCTION OF MAIN COMPONENTS
The SRS airbag system mainly consists of the parts listed in the table below.
| Components | Outline | |
|---|---|---|
|
*: Models with occupant classification system |
||
| SRS Airbag | Mainly consists of an inflator and a bag. Upon receiving a deployment signal from the airbag sensor assembly, the inflator generates gas to deploy the bag. | |
| Front Seat Outer Belt Assembly | Used to help reduce impact to the occupants. | |
| Airbag Sensor | Detects the deceleration of the vehicle during a collision, and transmits the signal to the airbag sensor assembly, from which the airbag sensor assembly determines whether deployment is necessary. | |
| Front Seat Inner Belt Assembly* | Seat Belt Buckle Switch for Driver | Detects if the driver seat belt is fastened. |
| Seat Belt Buckle Switch for Front Passenger | Detects if the front passenger seat belt is fastened. | |
| Occupant Classification Sensor* | Detects distortion, and transmits signals corresponding to occupant's weights to the occupant detection ECU. | |
| Airbag Sensor Assembly | ·
Detects the deceleration of the vehicle during a collision, determines whether deployment is necessary based on the signals from each airbag sensor, and transmits deployment signals to each SRS airbag and seat belt pretensioner. ·
Provides initial check and diagnosis function. |
|
| Occupant Detection ECU* | Judges whether the front passenger seat is occupied using signals from 2 occupant classification sensors and front passenger seat belt buckle switch. | |
| SRS Warning Light | Provided in the combination meter assembly and comes on when the SRS airbag system malfunctions. | |
| Hybrid Vehicle Control ECU | ·
The hybrid vehicle control ECU receives a SRS airbag deployment signal from the airbag sensor assembly during a frontal, side or side rear collision, and sends the engine stop signal to the ECM. ·
In the event of a collision, the hybrid vehicle control ECU shuts down the hybrid system power supply by turning the System Main Relays (SMRs) off, in order to protect occupants from the possibility of electric shock. |
|
| ECM | Stops the fuel pump when the engine stop signal is received. | |
OPERATING CONDITION
Ignition Condition
Deceleration sensors used for the SRS airbag system are installed on various parts on the vehicle and transmit the deceleration data of each part during a collision.
Depending on the situation, the airbag sensor assembly sends a deployment signal to each SRS airbag based on the information from each sensor.
Frontal collision signals are produced based on the information from the airbag sensor assembly and front airbag sensors. Frontal collision signals are used to deploy the SRS driver airbag, SRS front passenger airbag, SRS seat cushion airbags*, SRS driver knee airbag, SRS curtain shield airbags and to activate the seat belt pretensioners.
*: Models with occupant classification system
Side collision signals are produced based on the combined information from the airbag sensor assembly and a side airbag sensor assembly, No. 2 side airbag sensor assembly or door side airbag sensor*. Side collision signals are used to deploy the SRS side airbag, SRS curtain shield airbag and to activate the seat belt pretensioner.
*: Models with occupant classification system
If a collision signal is transmitted from a No. 2 side airbag sensor assembly only, a SRS side airbag will not deploy and also a seat belt pretensioner will not be activated.
Side rear collision signals are produced based on the combined information from the airbag sensor assembly, a side airbag sensor assembly and No. 2 side airbag sensor assembly. Side rear collision signals are used to deploy the SRS curtain shield airbag.
SYSTEM CONTROL
SRS Airbag for Frontal Collision
For frontal collisions, there are 7*1 or 5*2 airbags and 2 seat belt pretensioners: a SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag, SRS seat cushion airbag LH*1, SRS seat cushion airbag RH*1, SRS curtain shield airbag LH, SRS curtain shield airbag RH, front seat outer belt assembly LH and front seat outer belt assembly RH. The deployment of the SRS airbags and the activation of the seat belt pretensioners occur simultaneously.
The SRS driver airbag and the SRS front passenger airbag use dual-stage control. This controls the airbag inflating output by judging the extent of impact and whether or not the seat belt is fastened.*1
The airbag sensor assembly determines whether the SRS seat cushion airbag LH should be deployed based on the signals received from the seat belt buckle switch in the front seat inner belt assembly LH.*1
When the SRS front passenger airbag is deployed, the airbag sensor assembly activates the actuator in response to the signal from the occupant detection ECU to open the front passenger sub-vent hole, regulating the internal pressure of the SRS front passenger airbag to the optimum level.*1
*1: Models with occupant classification system
*2: Models without occupant classification system
SRS Airbag for Side or Side Rear Collision
For a side collision, if the side airbag sensor assembly and door side airbag sensor* detect an impact, they inform the airbag sensor assembly, and the airbag sensor assembly causes the SRS side airbag, SRS curtain shield airbag and seat belt pretensioner to be deployed and operated simultaneously.
*: Models with occupant classification system
For a side rear collision, if the No. 2 side airbag sensor assembly detects an impact, it informs the airbag sensor assembly via the side airbag sensor assembly, and the airbag sensor assembly causes the SRS curtain shield airbag to be deployed.
SRS Airbag for Roll Over (Models with Occupant Classification System)
If the vehicle is tilted and rolls over, the airbag sensor assembly activates the seat belt pretensioners and deploys the SRS curtain shield airbags based on signals that show the vehicle's roll angle and rotation speed.
If the vehicle rolls over in a side collision, the airbag sensor assembly causes the SRS side airbag and SRS curtain shield airbag to deploy and activates the seat belt pretensioners based on signals from the side airbag sensor assembly, No. 2 side airbag sensor assembly and door side airbag sensor. Meanwhile, the airbag sensor assembly activates the seat belt pretensioners and deploys the SRS curtain shield airbag on the opposite side of the collision, based on lateral deceleration and rotation speed signals.
Primary Check Illumination Control
After the ignition switch is turned ON, the airbag sensor assembly illuminates the SRS warning light in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of SRS airbags is prohibited and a diagnosis of the airbag sensor assembly is performed. If trouble is detected during the primary check, the SRS warning light remains on even after the 6 seconds have elapsed. See the illustration below.
CONSTRUCTION
SRS Driver Airbag
The SRS driver airbag contains a set of 2 initiators and propellants. The airbag sensor assembly helps optimize the airbag deployment rate by controlling the ignition timing of the initiators.*1
The SRS driver airbag mainly consist of an inflator and a bag.*2
*1: Models with occupant classification system
*2: Models without occupant classification system
SRS Front Passenger Airbag
The SRS front passenger airbag contains a set of 2 initiators, propellants and actuator. The airbag sensor assembly helps optimize the airbag deployment rate by controlling the ignition timing of the initiators and the opening/closing of the front passenger sub-vent hole.*1
SRS front passenger airbag mainly consist of an inflator and a bag.*2
*1: Models with occupant classification system
*2: Models without occupant classification system
SRS Driver Knee Airbag
The SRS driver knee airbag consists of an inflator and a bag.
SRS Seat Cushion Airbag (Models with Occupant Classification System)
The SRS seat cushion airbag consists of an inflator and a bag.
SRS Curtain Shield Airbag
SRS curtain shield airbag that extend from the front pillar to the roof side rail are installed. Each SRS curtain shield airbag consists of an inflator and a bag.
SRS Side Airbag
SRS side airbags are installed in the seat backs of the driver seat and the front passenger seat. Each SRS side airbag consists of an inflator, a bag and a cover.
Front Airbag Sensor
A deceleration sensor is enclosed in the front airbag sensor. Based on the deceleration of the vehicle during a front collision, a distortion is created in the sensor and converted into an electrical signal. Accordingly, the extent of the initial collision can be detected in detail.
Side Airbag Sensor Assembly, No. 2 Side Airbag Sensor Assembly and Door Side Airbag Sensor*
A deceleration sensor is enclosed in the side airbag sensor assembly, No. 2 side airbag sensor assembly and door side airbag sensor*. Based on the deceleration of the vehicle during a side or side rear collision, a distortion is created in the sensor and converted into an electrical signal.
*: Models with occupant classification system
Seat Belt Buckle Switch (Models with Occupant Classification System)
The built-in seat belt buckle switch of the front seat inner belt assembly detects that the seat belt is fastened.
A non-contact type switch is built into the front seat inner belt assembly on the driver and front passenger sides.
This switch contains a Hall IC and magnet.
The ejector inside the seat belt buckle switch and the plate installed to the ejector move when the seat belt is removed or inserted. The movement of the plate changes the magnetic flux density of the magnet.
The Hall IC detects changes in the magnetic flux density. These changes indicate that the seat belt is either fastened or unfastened, and the Hall IC outputs a signal to the airbag sensor assembly (for driver) or occupant detection ECU (for front passenger).
| *1 | Ejector | *2 | Magnet |
| *3 | Hall IC | *4 | Plate |
| *5 | Magnetic Flux | - | - |
| *a | Seat belt not fastened | *b | Seat belt fastened |
OPERATION
Front Passenger Sub-vent Hole (Models with Occupant Classification System)
The airbag sensor assembly activates the actuator in response to signals from the occupant detection ECU.
When the actuator is activated, the pin gets into the inside of the actuator to release the belt, as a result, the front passenger sub-vent hole will open due to the deployment pressure of the SRS front passenger airbag.
| *1 | Actuator | *2 | Belt |
| *3 | Bag | *4 | Pin |
| *a | Front Passenger Sub-vent Hole Closed | *b | Actuator Cross Section |
| *1 | Actuator | *2 | Belt |
| *3 | Bag | *4 | Pin |
| *a | Front Passenger Sub-vent Hole Open | *b | Actuator Cross Section |
|
Pin gets into the inside of the actuator |
|
Releases |
DIAGNOSIS
If the airbag sensor assembly detects a malfunction in the SRS airbag system, the airbag sensor assembly stores the malfunction data in memory, in addition to illuminating the SRS warning light.
The airbag sensor assembly outputs malfunction data and Diagnostic Trouble Codes (DTCs) to the Global TechStream (GTS).
The DTCs can be read after connecting the Global Techstream (GTS) to the DLC3. For details, refer to the Repair Manual.
If the SRS airbag deploys, the airbag sensor assembly will turn on the SRS warning light. However, different from the ordinary diagnosis function, a DTC will not be stored. The SRS warning light cannot be turned off. It is necessary to replace the airbag sensor assembly with a new one.