Home › Engine / Hybrid System › 1NZ-FXE (EMISSION CONTROL) › EMISSION CONTROL SYSTEM (w/ Canister Pump Module) › from 2017.06
NM2170E _51 Engine / Hybrid System _056962 1NZ-FXE EMISSION CONTROL _0319451 EMISSION CONTROL SYSTEM(w/ Canister Pump Module) UN GENERAL/CONTROL/DETAILS F

1NZ-FXE EMISSION CONTROL  EMISSION CONTROL SYSTEM(w/ Canister Pump Module)  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the 1NZ-FXE emission control system are as follows.

Component Function
TWC Oxidizes CO and HC in the exhaust gas and deoxidizes NOx at the same time, to purify them into CO2, H2O and N2.
Oxygen Sensor This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
Air Fuel Ratio Sensor As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust gas. However, it detects the oxygen concentration in the exhaust gas linearly.
E.F.I. Vacuum Sensor Assembly Uses built-in semiconductors to detect the intake manifold pressure.
EGR Valve Assembly Operates when receiving signals from the ECM, regulating the EGR volume.
EGR Cooler Assembly Cools the exhaust gas temperature to improve the EGR efficiency.
Ventilation Valve Sub-assembly Opens and closes using vacuum generated in the intake manifold and controls the flow rate of the blowby gas.
Charcoal Canister Assembly Contains activated charcoal to absorb the fuel vapors that are created in the fuel tank assembly.
Canister Pump Module Vent Valve Opens and closes the fresh air line in accordance with the signals from the ECM.
Leak Detection Pump Applies vacuum pressure in the evaporative emission control system in accordance with the signals from the ECM.
Canister Pressure Sensor Detects the pressure in the evaporative emission control system and sends the signals to the ECM.
No. 1 Charcoal Canister Filter Prevents dust and debris in the fresh air from entering the system.
Fresh Air Line Fresh air goes into the canister and the cleaned drain air goes out into the atmosphere.
Purge VSV Opens in accordance with the signals from the ECM when the system is purging, in order to send the fuel vapor that was absorbed by the charcoal canister assembly into the intake manifold.
ECM
·

Controls the volume of fuel injected, with corrections based primarily on the signal from the air fuel ratio sensor, and minor corrections based on the signal from the oxygen sensor. This control optimizes the air-fuel ratio.

·

Regulates the EGR volume in accordance with the various sensor signals.

·

Controls the canister pump module and the purge VSV in accordance with the signals from various sensors, in order to achieve a purge volume that suits the driving conditions. In addition, the ECM monitors the system for any leaks and stores a DTC if a malfunction is found.





OPERATING CONDITION


a.

Approximately 5 hours after the power switch has been turned off, the ECM operates the canister pump module to detect any evaporative emission leakage occurring between the fuel tank assembly and the canister through changes in the fuel tank assembly pressure.


b.

The following are the typical conditions necessary to enable an evaporative emission leak check.

Typical Enabling Condition
·

5 hours have elapsed after the engine has been turned off*.

·

Altitude: Below 2400 m (8000 feet)

·

Auxiliary Battery Voltage: 10.5 V or more

·

Power Switch: OFF

·

Engine Coolant Temperature: 4.4 to 35°C (40 to 95°F)

·

Intake Air Temperature: 4.4 to 35°C (40 to 95°F)



*: If engine coolant temperature does not drop below 35°C (95°F), this time should be extended to 7 hours. Even after that, if the temperature is not less than 35°C (95°F), the time should be extended to 9.5 hours.


HINT:

The canister pump module performs a fuel evaporative emission leakage check. This check is done approximately five hours after the engine is turned off. Sound may be heard coming from underneath the luggage compartment for several minutes. This does not indicate a malfunction. Pinpoint pressure test procedure is adopted by pressurizing the fresh air line that runs from the canister pump module to the air filler neck. For details, refer to the Repair Manual.




SYSTEM CONTROL


a.

EGR Control

i.

For the EGR system, a regulated amount of inert gas is allowed to flow into the intake passage, reducing the peak temperature in the engine combustion chamber.


ii.

By sensing the engine driving conditions, the ECM operates the EGR valve assembly and throttle control motor, to regulate the amount of exhaust gas that is recirculated.

W136309E01
5.417,4.25 5.583,4.25 5.583,4.25 5.823,3.917 true 5.167,3 5.333,3 5.333,3 5.625,2.667 true 5.25,1.917 5.417,1.917 5.417,1.917 5.708,1.583 true 0.813,0.333 2.448,0.563 1.635,0.229 10 false Crank Position Sensor 0.177,0.75 2.229,0.979 2.052,0.229 10 false E.F.I. Vacuum Sensor Assembly 0.5,1.156 2.219,1.469 1.719,0.313 10 false Intake Mass Air Flow Meter Sub-assembly 0.313,1.719 2.448,1.948 2.135,0.229 10 false Intake Air Temperature Sensor 0.854,2.188 2.188,2.688 1.333,0.5 10 false E.F.I. Engine Coolant Temperature Sensor 0.26,2.906 2.26,3.156 2,0.25 10 false Hybrid Vehicle Control ECU 0.135,3.906 2.469,4.073 2.333,0.167 10 false Accelerator Pedal Sensor Assembly 0.573,4.417 2.656,4.646 2.083,0.229 10 false : CAN Communication Line 3.302,1.563 3.885,1.792 0.583,0.229 10 false ECM 4.125,0.354 6.427,0.583 2.302,0.229 10 false Throttle Position Sensor Signal 4.115,0.833 5.75,1.063 1.635,0.229 10 false Throttle Valve Control 4.115,1.26 5.75,1.49 1.635,0.229 10 false EGR Valve Control 4.531,1.823 5.281,2.156 0.75,0.333 10 false EGR Valve Assembly 4.365,2.917 5.167,3.229 0.802,0.313 10 false EGR Cooler Assembly 4.573,4.156 5.656,4.406 1.083,0.25 10 false Exhaust Gas 6.448,3.167 6.948,3.417 0.5,0.25 10 false Engine



b.

Blowby Gas Ventilation System

i.

By introducing blowby gas that has a large amount of HC into the air intake side and burning it again, the system attempts to enhance the emission performance. Returning blowby gas volume is regulated to the appropriate amount corresponding to the engine operating conditions, reducing the engine oil quantity taken away and engine idling speeds.


ii.

The ventilation valve sub-assembly passage returns the blowby gas into the area after the throttle valve in accordance with the intake manifold vacuum.


iii.

When load is low, the passage from the cylinder head cover sub-assembly to the area before the throttle valve increases the air purification performance inside the crankcase by introducing fresh air, and when load is high, the passage circulates the blowby gas together with the ventilation valve sub-assembly side passage due to the intake manifold vacuum.

W105000C07
1.917,1.208 1.698,0.594 1.698,0.594 1.583,0.594 false 1.365,0.521 1.615,0.729 0.25,0.208 10 false *1 2.24,0.552 2.49,0.76 0.25,0.208 10 false *a 4.802,0.542 5.052,0.75 0.25,0.208 10 false *b
*1 Ventilation Valve Sub-assembly - -
*a When load is low *b When load is high
V100135

Blowby Gas
V100136

Fresh Air




c.

Purge Flow Control

i.

The canister stores the fuel vapors that have been created in the fuel tank assembly.


ii.

When the engine has reached predetermined parameters (closed loop, engine coolant temp. above 80°C (176°F), etc.), stored fuel vapors are purged from the canister whenever the purge VSV is opened by the ECM.


iii.

The ECM will change the duty ratio cycle of the purge VSV, thus controlling purge flow volume. Purge flow volume is determined by intake manifold pressure and the duty ratio cycle of the purge VSV. Atmospheric pressure is allowed into the canister to ensure that purge flow is constantly maintained whenever purge vacuum is applied to the canister.

W105958E02
1.323,2.604 1.698,2.781 0.375,0.177 10 false ECM 0.333,1.083 1.073,1.448 0.74,0.365 10 false Purge VSV (Open) 1.198,0.146 2.375,0.313 1.177,0.167 10 false to Intake Manifold 2.26,1.792 3.635,1.958 1.375,0.167 10 false Fuel Tank Assembly 1.99,0.448 2.792,0.594 0.802,0.146 10 false Atmosphere 3.844,1.469 4.781,1.677 0.938,0.208 10 false Purge Air Line 4.146,1.969 4.833,2.125 0.688,0.156 10 false Vent Valve 5.74,3.042 6.906,3.396 1.167,0.354 10 false Charcoal Canister Assembly 3.854,3.385 5.302,3.552 1.448,0.167 10 false Canister Pump Module



d.

On-board Refueling Vapor Recovery (ORVR)

i.

When the internal pressure of the fuel tank assembly increases during refueling, fuel vapors are fed to the canister. The air that has had the fuel vapors removed from it will be discharged through the fresh air line.


ii.

The vent valve is used to open and close the fresh air line, and it is always open (even when the engine is stopped) except when the vehicle is in monitoring mode (the valve will be open as long as the vehicle is not in monitoring mode). If the vehicle is refueled in system monitoring mode, the ECM will recognize the refueling by way of the canister pressure sensor, which detects the sudden pressure increase in the fuel tank assembly, and the ECM will open the vent valve.

W105959E02
0.104,0.594 1.344,0.75 1.24,0.156 10 false Purge VSV (Close) 2.021,1.698 3.5,1.865 1.479,0.167 10 false Fuel Tank Assembly 2.198,2.521 3.094,2.677 0.896,0.156 10 false Fresh Air Line 4.063,1.917 4.75,2.073 0.688,0.156 10 false Vent Valve 3.75,3.458 5.198,3.625 1.448,0.167 10 false Canister Pump Module 5.792,3.063 6.969,3.417 1.177,0.354 10 false Charcoal Canister Assembly



e.

EVAP Leak Check

i.

The EVAP leak check operates in accordance with the following timing chart:

W101551E12
6.75,5.344 6.969,5.615 0.219,0.271 10 false 6) 5.99,5.354 6.208,5.625 0.219,0.271 10 false 5) 5.198,5.365 5.417,5.635 0.219,0.271 10 false 4) 4.104,5.354 4.323,5.625 0.219,0.271 10 false 3) 2.573,5.354 2.792,5.625 0.219,0.271 10 false 2) 1.833,5.354 2.052,5.625 0.219,0.271 10 false 1) 0.115,0.073 1.458,0.302 1.344,0.229 12 false - Timing Chart 0.146,0.646 0.573,1.177 0.427,0.531 10 false Purge VSV 0.146,1.563 0.531,2.01 0.385,0.448 10 false Vent Valve 0.125,2.344 1.125,2.531 1,0.188 10 false Pump Motor 0.125,3.938 1.281,4.125 1.156,0.188 10 false System Pressure 0.083,3.365 1.51,3.552 1.427,0.188 10 false Atmospheric Pressure 0.417,4.51 1.573,4.698 1.156,0.188 10 false 0.02 in. Pressure 0.813,0.583 1.615,0.833 0.802,0.25 10 false ON (Open) 1.271,1.396 1.583,1.646 0.313,0.25 10 false ON 0.792,1.729 1.625,1.979 0.833,0.25 10 false OFF (Vent) 1.26,2.188 1.573,2.438 0.313,0.25 10 false ON 1.229,2.604 1.594,2.854 0.365,0.25 10 false OFF 0.729,0.938 1.583,1.188 0.854,0.25 10 false OFF (Close)

Order Operation Description Time
1) Atmospheric Pressure Measurement The ECM turns the vent valve off (vent) and measures EVAP system pressure to determine the atmospheric pressure. 60 sec.
2) 0.02 in. Leak Pressure Measurement

The leak detection pump creates negative pressure (vacuum) through a 0.02 in. orifice and the pressure is measured. The ECM determines this as the 0.02 in. leak pressure.

The purpose of this measurement is to confirm vacuum pump operation, and to provide a baseline measurement value that will be used for comparison in subsequent leak test steps.


360 sec.
3) EVAP Leak Check

The leak detection pump creates negative pressure (vacuum) in the EVAP system and the EVAP system pressure is measured.

If the stabilized pressure is larger than the 0.02 in. leak pressure, ECM determines that the EVAP system has a leak.

If the EVAP pressure does not stabilize within 15 minutes, the ECM cancels EVAP monitor.


Within 15 min.
4) Purge VSV Monitor The ECM opens the purge VSV and measures the EVAP pressure increase. If the increase is large, the ECM interprets this as normal. 10 sec.
5) Repeat 0.02 in. Leak Pressure Measurement The leak detection pump creates negative pressure (vacuum) through the 0.02 in. orifice and the pressure is measured. The ECM determines this as the 0.02 in. leak pressure. 60 sec.
6) Final Check The ECM measures the atmospheric pressure and records the monitor result. -




CONSTRUCTION


a.

Three-Way Catalytic converter (TWC)

i.

TWCs are provided in the exhaust manifold and also in the front exhaust pipe assembly.


ii.

An exhaust manifold with an integrated TWC is used for warm-up of the TWC.


iii.

These TWCs enable improved exhaust emissions with an optimized cell density and wall thickness.

W105960C01
1.502,1 1.676,1.157 0.174,0.157 10 *1 1.175,1.608 1.351,1.07 false 1.356,1.07 1.49,1.07 false 2.138,1.284 2.312,1.441 0.174,0.157 10 *1 1.811,1.892 1.987,1.354 false 1.992,1.354 2.126,1.354 false
*1 TWC - -




b.

Fuel Inlet (Fresh Air Inlet)

i.

The fresh air line inlet is located the near the fuel inlet pipe opening. The fresh air from the atmosphere and drain air cleaned by the canister will go in or out of the system through the passages shown below.

W105058C01
2.885,0.688 2.708,0.344 2.708,0.344 2.531,0.344 false 3.177,1.969 2.135,1.156 2.135,1.156 1.958,1.156 false 3.698,2.406 2.625,2.813 2.625,2.813 2.448,2.813 false 4.281,2.979 3.427,3.323 3.427,3.323 3.25,3.323 false 4.271,1.76 4.927,1.24 4.927,1.24 5.104,1.24 false 2.365,0.26 2.552,0.469 0.188,0.208 10 false *1 1.771,1.063 1.958,1.271 0.188,0.208 10 false *2 2.271,2.719 2.458,2.927 0.188,0.208 10 false *a 3.063,3.229 3.25,3.438 0.188,0.208 10 false *b 5.146,1.146 5.333,1.354 0.188,0.208 10 false *3 4.604,3.25 4.792,3.458 0.188,0.208 10 false *c
*1 Fuel Tank Cap Assembly *2 No. 1 Charcoal Canister Filter
*3 Fuel Inlet Pipe - -
*a Cleaned Drain Air *b Fresh Air
*c To canister - -




c.

EGR Valve Assembly and EGR Cooler Assembly

i.

A step motor type EGR valve assembly is used to precisely control the EGR gas flow amount.


ii.

The EGR cooler assembly cools the exhaust gas to improve the EGR efficiency.

W135039C01
3.76,5.167 5.333,6.083 5.333,6.083 5.51,6.083 true 3.052,3.469 2,3.917 2,3.917 1.833,3.917 true 3.385,4.469 1.667,5.167 1.667,5.167 1.5,5.167 true 4.292,3.219 4.833,2.667 4.833,2.667 5,2.667 true 5.938,1.083 6.25,0.75 6.25,0.75 6.417,0.75 true 5.542,1.073 5.25,0.75 5.25,0.75 5.083,0.75 true 4.844,0.688 5.156,0.844 0.313,0.156 10 false *1 6.479,0.677 6.792,0.833 0.313,0.156 10 false *2 1.625,3.833 1.938,3.99 0.313,0.156 10 false *3 5.083,2.604 5.396,2.76 0.313,0.156 10 false *4 1.271,5.083 1.583,5.24 0.313,0.156 10 false *5 5.635,6.01 5.948,6.167 0.313,0.156 10 false *6 1.854,1.25 2.167,1.406 0.313,0.156 10 false *a 1.219,2.219 1.531,2.375 0.313,0.156 10 false *b 4.677,0.479 4.99,0.635 0.313,0.156 10 false *c 3.833,4.344 3.99,4.542 0.156,0.198 10 true A 3,4.333 3.156,4.531 0.156,0.198 10 true A
*1 Water Passage *2 EGR Gas Passage
*3 EGR Valve Assembly *4 No. 2 EGR Pipe
*5 EGR Cooler Assembly *6 No. 1 EGR Pipe
*a To Intake Manifold *b From Exhaust Manifold
*c A-A Cross Section - -
V100135

EGR Gas - -




d.

E.F.I. Vacuum Sensor Assembly

i.

An E.F.I. vacuum sensor assembly is used to measure the intake manifold pressure for EGR control.


ii.

The E.F.I. vacuum sensor assembly consists of a silicon chip which utilizes the characteristic of a silicon chip that changes its electrical resistance when pressure is applied to it. The sensor converts the pressure into an electrical signal, and sends it to the ECM in an amplified form.

W101304E16
4.615,0.219 4.802,0.219 false 4.802,0.219 4.917,1.125 false 0.854,2.385 3.146,2.719 2.292,0.333 10 false Manifold Absolute Pressure Sensor 4.615,2.615 5.552,2.948 0.938,0.333 10 false Cross Section 3.823,0.146 4.688,0.479 0.865,0.333 10 false Silicon Chip 1.479,4.417 2.365,4.854 0.885,0.438 10 false Output Voltage (V) 2.573,5.615 3.167,5.948 0.594,0.333 10 false Vacuum 3.125,6.302 4.75,6.635 1.625,0.333 10 false Vacuum Sensor Output 4.615,5.625 5.458,6.177 0.844,0.552 10 false Atmosphere Pressure 3.656,5.604 4.333,6.104 0.677,0.5 10 false Intake Manifold Pressure 2.417,3.802 2.76,4.135 0.344,0.333 10 false 4.2 2.417,4.438 2.76,4.771 0.344,0.333 10 false 2.4 2.417,5.313 2.76,5.646 0.344,0.333 10 false 0.6




OPERATION


a.

Atmospheric Pressure Measurement

i.

When the power switch is turned off, the purge VSV and the vent valve are turned off. Therefore, atmospheric pressure is introduced into the canister.


ii.

The ECM measures the atmospheric pressure based on the signals provided by the canister pressure sensor.


iii.

If the measurement value is out of standards, the ECM actuates the leak detection pump in order to monitor the changes in the pressure.

W105964E01
0.33,0.542 1.446,0.702 1.116,0.160 10 Purge VSV (Off) 0.688,4.468 1.410,4.628 0.722,0.160 10 Purge VSV 1.084,2.475 1.462,2.650 0.378,0.175 10 ECM 2.064,1.6 3.496,1.765 1.433,0.165 10 Fuel Tank Assembly 2.105,2.892 3.482,3.077 1.376,0.185 10 Leak Detection Pump 3.718,1.795 4.747,1.947 1.029,0.152 10 Vent Valve (Off) 0.688,5.198 1.724,5.350 1.036,0.152 10 Vent Valve 2.085,4.262 2.771,4.414 0.685,0.152 10 On (Open) 2.058,4.65 2.770,4.803 0.712,0.152 10 Off (Close) 2.134,5.419 2.771,5.572 0.637,0.152 10 Off (Vent) 2.549,5.034 2.775,5.186 0.226,0.152 10 On 2.549,5.804 2.775,5.957 0.226,0.152 10 On 2.549,6.194 2.775,6.347 0.226,0.152 10 Off 0.688,5.872 1.488,6.025 0.800,0.152 10 Pump Motor 1.363,6.619 2.764,6.771 1.401,0.152 10 Atmospheric Pressure 2.016,8.397 4.326,8.549 2.310,0.152 10 Atmospheric Pressure Measurement 0.688,7.018 1.766,7.170 1.078,0.152 10 System Pressure 1.662,7.501 2.767,7.653 1.105,0.152 10 0.02 in. Pressure 1.852,3.27 3.476,3.455 1.624,0.184 10 Canister Pressure Sensor 3.678,3.628 5.125,3.795 1.448,0.166 10 Canister Pump Module 5.683,2.935 6.910,3.294 1.227,0.359 10 Charcoal Canister Assembly 4.237,2.575 3.617,2.987 3.617,2.987 3.502,2.987 false 4.604,2.913 3.677,3.369 3.677,3.369 3.505,3.369 false 3.115,8.123 3.115,8.387 false



b.

0.02 in. Leak Pressure Measurement

i.

The vent valve remains off, and the ECM introduces atmospheric pressure into the canister and actuates the leak detection pump in order to create a negative pressure.


ii.

At this time, the pressure will not decrease beyond a 0.02 in. pressure due to the atmospheric pressure that enters through a 0.02 in. diameter reference orifice.


iii.

The ECM compares the logic value and this pressure, and stores it as a 0.02 in. leak pressure in its memory.


iv.

If the measurement value is below the standard, the ECM will determine that the reference orifice is clogged and store Diagnostic Trouble Code (DTC) P043E in its memory.


v.

If the measurement value is above the standard, the ECM will determine that a high flow rate pressure is passing through the reference orifice and store Diagnostic Trouble Code (DTC) P043F, P2401 and P2402 in its memory.

W105965E02
4.302,2.563 3.677,2.969 3.677,2.969 3.573,2.969 false 4.667,2.896 3.74,3.354 3.74,3.354 3.573,3.354 false 3.531,8.094 3.531,8.354 false 5.135,3.031 5.646,3.719 5.646,3.719 5.948,3.719 false 0.292,0.542 1.438,0.698 1.146,0.156 10 false Purge VSV (Off) 0.75,4.448 1.469,4.604 0.719,0.156 10 false Purge VSV 1.146,2.458 1.521,2.635 0.375,0.177 10 false ECM 2.125,1.583 3.563,1.75 1.438,0.167 10 false Fuel Tank Assembly 2.167,2.875 3.542,3.063 1.375,0.188 10 false Leak Detection Pump 3.792,1.781 4.885,1.938 1.094,0.156 10 false Vent Valve (Off) 0.75,5.177 1.958,5.333 1.208,0.156 10 false Vent Valve 1.938,4.25 2.625,4.406 0.688,0.156 10 false On (Open) 1.917,4.635 2.625,4.792 0.708,0.156 10 false Off (Close) 1.99,5.406 2.625,5.563 0.635,0.156 10 false Off (Vent) 2.406,5.021 2.635,5.177 0.229,0.156 10 false On 2.406,5.792 2.635,5.948 0.229,0.156 10 false On 2.406,6.177 2.635,6.333 0.229,0.156 10 false Off 0.75,5.854 1.552,6.01 0.802,0.156 10 false Pump Motor 1.219,6.604 2.615,6.76 1.396,0.156 10 false Atmospheric Pressure 2.688,8.344 5,8.5 2.313,0.156 10 false 0.02 in. Pressure Measurement 0.75,7 1.823,7.156 1.073,0.156 10 false System Pressure 1.521,7.469 2.625,7.625 1.104,0.156 10 false 0.02 in. Pressure 1.917,3.25 3.542,3.438 1.625,0.188 10 false Canister Pressure Sensor 3.74,3.615 5.188,3.781 1.448,0.167 10 false Canister Pump Module 5.75,2.917 6.865,3.271 1.115,0.354 10 false Charcoal Canister Assembly 6.01,3.563 6.698,3.896 0.688,0.333 10 false Reference Orifice



c.

EVAP Leak Check

i.

While actuating the leak detection pump, the ECM turns the vent valve on in order to introduce a vacuum into the canister.


ii.

When the pressure in the system stabilizes, the ECM compares this pressure and the 0.02 in. pressure in order to check for a leakage.


iii.

If the detection value is below the 0.02 in. pressure, the ECM determines that there is no leakage.


iv.

If the detection value is above the 0.02 in. pressure and near atmospheric pressure, the ECM determines that there is a gross leakage (large hole).


v.

If the detection value is above the 0.02 in. pressure, the ECM determines that there is a small leakage.

W105966E01
0.093,0.415 1.241,0.575 1.148,0.160 10 Purge VSV (Off) 0.558,4.321 1.280,4.481 0.722,0.160 10 Purge VSV 0.982,2.429 1.361,2.604 0.378,0.175 10 ECM 1.934,1.453 3.425,1.618 1.491,0.165 10 Fuel Tank Assembly 1.985,2.813 3.362,2.998 1.376,0.185 10 Leak Detection Pump 3.777,1.627 4.791,1.780 1.014,0.152 10 Vent Valve (On) 0.558,5.051 1.442,5.203 0.884,0.152 10 Vent Valve 1.591,4.115 2.276,4.267 0.685,0.152 10 On (Open) 1.564,4.503 2.276,4.656 0.712,0.152 10 Off (Close) 1.639,5.272 2.277,5.425 0.637,0.152 10 Off (Vent) 2.054,4.887 2.280,5.039 0.226,0.152 10 On 2.054,5.657 2.280,5.809 0.226,0.152 10 On 2.054,6.047 2.280,6.200 0.226,0.152 10 Off 0.558,5.725 1.358,5.877 0.800,0.152 10 Pump Motor 0.869,6.472 2.270,6.624 1.401,0.152 10 Atmospheric Pressure 3.681,8.228 4.856,8.380 1.175,0.152 10 EVAP Leak Check 3.728,6.271 4.722,6.424 0.995,0.152 10 Gross Leakage 3.802,6.799 4.797,6.951 0.995,0.152 10 Small Leakage 3.592,7.439 4.092,7.591 0.499,0.152 10 Normal 0.558,6.871 1.636,7.023 1.078,0.152 10 System Pressure 1.168,7.34 2.273,7.492 1.105,0.152 10 0.02 in. Pressure 1.726,3.269 3.350,3.453 1.624,0.184 10 Canister Pressure Sensor 3.619,3.475 5.066,3.641 1.448,0.166 10 Canister Pump Module 5.553,2.788 6.780,3.147 1.227,0.359 10 Charcoal Canister Assembly 5.798,3.494 6.920,3.657 1.122,0.163 10 Reference Orifice 4.107,2.428 3.487,2.911 3.487,2.911 3.372,2.911 false 4.474,2.825 3.547,3.36 3.547,3.36 3.375,3.36 false 4.218,7.962 4.218,8.226 false 4.945,2.904 5.453,3.584 5.453,3.584 5.75,3.584 false



d.

Purge VSV Monitor

i.

After completing an EVAP leak check, the ECM turns the purge VSV on (open) with the leak detection pump actuated, and introduces the atmospheric pressure from the intake manifold to the canister.


ii.

If the pressure change at this time is within the normal range, the ECM determines the condition to be normal.


iii.

If the pressure is out of the normal range, the ECM will stop the purge VSV monitor and store DTC P0441 in its memory.

W105967E02
0.414,0.521 1.507,0.681 1.093,0.160 10 Purge VSV (On) 0.492,4.447 1.214,4.607 0.722,0.160 10 Purge VSV 1.182,2.558 1.561,2.733 0.378,0.175 10 ECM 2.204,1.575 3.623,1.739 1.419,0.165 10 Fuel Tank Assembly 2.207,2.924 3.583,3.109 1.376,0.185 10 Leak Detection Pump 3.844,1.746 5.116,1.899 1.272,0.152 10 Vent Valve (On) 0.492,5.065 1.738,5.217 1.247,0.152 10 Vent Valve 1.413,4.227 2.098,4.379 0.685,0.152 10 On (Open) 1.386,4.615 2.098,4.768 0.712,0.152 10 Off (Close) 1.461,5.384 2.098,5.537 0.637,0.152 10 Off (Vent) 1.876,4.999 2.102,5.151 0.226,0.152 10 On 1.876,5.769 2.102,5.922 0.226,0.152 10 On 1.876,6.145 2.102,6.298 0.226,0.152 10 Off 0.492,5.907 1.292,6.060 0.800,0.152 10 Pump Motor 0.69,6.598 2.092,6.751 1.401,0.152 10 Atmospheric Pressure 4.43,8.357 5.670,8.510 1.240,0.152 10 Purge VSV Monitor 4.3,7.078 4.808,7.230 0.509,0.152 10 Normal 5.173,7.624 5.607,7.777 0.435,0.152 10 P0441 0.492,6.997 1.570,7.149 1.078,0.152 10 System Pressure 0.99,7.466 2.094,7.618 1.105,0.152 10 0.02 in. Pressure 1.933,3.309 3.557,3.494 1.624,0.184 10 Canister Pressure Sensor 3.762,3.608 5.209,3.774 1.448,0.166 10 Canister Pump Module 5.767,2.914 6.994,3.273 1.227,0.359 10 Charcoal Canister Assembly 4.338,2.53 3.703,3.039 3.703,3.039 3.586,3.039 false 4.706,2.945 3.743,3.4 3.743,3.4 3.565,3.4 false 4.983,8.078 4.983,8.343 false



e.

Repeat 0.02 in. Leak Pressure Measurement

i.

While the ECM operates the leak detection pump, the purge VSV and vent valve turns off and a repeat 0.02 in. leak pressure measurement is performed.


ii.

The ECM compares the measured pressure with the pressure during EVAP leak check.


iii.

If the pressure during the EVAP leak check is below the measured value, the ECM determines that there is no leakage.


iv.

If the pressure during the EVAP leak check is above the 0.02 in. pressure and near atmospheric pressure, the ECM determines that there is a gross leakage (large hole) and stores DTC P0455 in its memory.


v.

If the pressure during the EVAP leak check is above the 0.02 in. pressure, the ECM determines that there is a small leakage and stores DTC P0456 in its memory.

W105968E01
0.07,0.547 1.218,0.706 1.148,0.160 10 Purge VSV (Off) 0.479,4.425 1.201,4.584 0.722,0.160 10 Purge VSV 0.903,2.533 1.282,2.708 0.378,0.175 10 ECM 1.854,1.557 3.249,1.722 1.395,0.165 10 Fuel Tank Assembly 1.906,2.916 3.282,3.101 1.376,0.185 10 Leak Detection Pump 3.652,1.893 4.664,2.045 1.012,0.152 10 Vent Valve (Off) 0.479,5.154 1.365,5.307 0.887,0.152 10 Vent Valve 1.47,4.19 2.155,4.343 0.685,0.152 10 On (Open) 1.443,4.579 2.155,4.731 0.712,0.152 10 Off (Close) 1.518,5.348 2.155,5.500 0.637,0.152 10 Off (Vent) 1.933,4.962 2.159,5.114 0.226,0.152 10 On 1.933,5.733 2.159,5.885 0.226,0.152 10 On 1.933,6.123 2.159,6.275 0.226,0.152 10 Off 0.479,5.829 1.279,5.981 0.800,0.152 10 Pump Motor 0.733,6.548 2.135,6.700 1.401,0.152 10 Atmospheric Pressure 4.251,8.313 6.745,8.465 2.495,0.152 10 Repeat 0.02 in. Pressure Measurement 3.971,6.454 4.419,6.606 0.448,0.152 10 P0455 4.153,7.225 4.583,7.377 0.430,0.152 10 P0456 3.588,7.542 4.087,7.695 0.499,0.152 10 Normal 0.479,6.974 1.557,7.127 1.078,0.152 10 System Pressure 1.047,7.415 2.151,7.568 1.105,0.152 10 0.02 in. Pressure 1.646,3.372 3.271,3.557 1.624,0.184 10 Canister Pressure Sensor 3.475,3.6 4.923,3.766 1.448,0.166 10 Canister Pump Module 5.431,2.88 6.658,3.239 1.227,0.359 10 Charcoal Canister Assembly 5.719,3.598 6.841,3.761 1.122,0.163 10 Reference Orifice 4.061,2.502 3.413,3.015 3.413,3.015 3.293,3.015 false 4.395,2.929 3.467,3.463 3.467,3.463 3.296,3.463 false 5.554,8.051 5.554,8.316 false 4.857,2.999 5.37,3.687 5.37,3.687 5.671,3.687 false