Home › Suspension › REAR SUSPENSION › REAR SUSPENSION SYSTEM › from 2017.06
NM2170E _53 Suspension _056971 REAR SUSPENSION _0277767 REAR SUSPENSION SYSTEM UN GENERAL/CONTROL/DETAILS F

REAR SUSPENSION  REAR SUSPENSION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Rear Coil Spring and Rear Shock Absorber Assembly

i.

Both ends of the coil spring have been formed into a small-diameter, pigtail shape. The compact construction has been designed to accommodate the low floor package.


ii.

Spring insulators are provided at the top and bottom ends of the rear coil springs, and the thickness of the insulators has been optimized to reduce vibration and achieve excellent ride comfort.


iii.

The low-pressure N2 gas sealed rear shock absorber assembly delivers stable damping force characteristics, providing excellent maneuverability and ride comfort.


iv.

A high response type piston valve provides damping force at very low shock absorber speeds, while also ensuring sufficient flow channel at medium and high speeds. This enhances steering response and suppresses high-frequency oscillations resulting in enhanced ride comfort.*

*: Destination package models for Australia, New Zealand and Korea

X136568C01
4.948,2.323 5.833,1.417 5.833,1.417 6,1.417 true 5.031,2.938 5.917,2 5.917,2 6.083,2 true 2.323,0.865 2.583,0.5 2.583,0.5 2.75,0.5 true 1.781,1 1.583,0.573 1.583,0.573 1.417,0.573 true 1.698,1.927 1.5,1.5 1.5,1.5 1.333,1.5 true 2.406,2.198 2,2.75 2,2.75 1.833,2.75 true 1.667,2 1.333,2.417 1.333,2.417 1.167,2.417 true 2.813,0.427 3.125,0.583 0.313,0.156 10 false *1 1.188,0.5 1.5,0.656 0.313,0.156 10 false *2 0.938,2.333 1.25,2.49 0.313,0.156 10 false *3 1.667,2.677 1.979,2.833 0.313,0.156 10 false *4 6.073,1.354 6.385,1.51 0.313,0.156 10 false *5 6.167,1.927 6.479,2.083 0.313,0.156 10 false *6 0.271,4.333 0.583,4.49 0.313,0.156 10 false *a
*1 Rear Upper Coil Spring Insulator *2 Rear Coil Spring
*3 Rear Suspension Support *4 Rear Lower Coil Spring Insulator
*5 Low-pressure (N2) Gas *6 Piston Valve
*a The illustrations shown are examples only. - -


NOTICE:

To prevent hazardous conditions, make sure to empty the gas from the shock absorber before discarding an N2 gas sealed shock absorber. For details, refer to the Repair Manual.




b.

Axle Beam and Trailing Arm

i.

The axle beam (rear axle beam assembly) offers not only high rigidity but also stability by optimized shearing center position.


ii.

The trailing arm (rear axle beam assembly) is fixed on the body via an angled bushing.


iii.

The inner cylinder of the rear axle carrier bush is made of aluminum, reducing the weight.

X136599C01
2.083,3.5 2.25,3.5 2.25,3.5 2.49,2.948 true 3.76,3.667 3.927,3.667 3.927,3.667 4.167,3.115 true 6,4.167 5.833,4.167 5.833,4.167 5.333,3.531 true 1.5,1 1.333,1 1.333,1 1.198,1.417 true 3.583,3.594 3.896,3.75 0.313,0.156 10 false *1 6.063,4.094 6.375,4.25 0.313,0.156 10 false *2 1.865,3.417 2.177,3.573 0.313,0.156 10 false *3 1.552,0.938 1.865,1.094 0.313,0.156 10 false *4 0.51,0.844 0.823,1 0.313,0.156 10 false *a
*1 Axle Beam (Rear Axle Beam Assembly) *2 Trailing Arm (Rear Axle Beam Assembly)
*3 Rear Axle Carrier Bush *4 Inner Cylinder
*a Cross Section - -
V100135

Front - -