Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2017.06
NM2170E _58 Vehicle Interior _056984 DOOR LOCK _0277782 POWER DOOR LOCK CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the power door lock control system have the following functions:

Component Function
Door Courtesy Light Switch Assembly Detects whether the doors are open or closed and sends this information to the main body ECU (multiplex network body ECU).
Door Lock Assembly Door Lock Position Switch Detects whether the doors are locked or unlocked and sends this information to the main body ECU (multiplex network body ECU).
Door Lock Motor Drives the motor in response to signals from the main body ECU (multiplex network body ECU) and locks or unlocks the doors.
Key-linked Switch Sends a lock or unlock request signal to the main body ECU (multiplex network body ECU) by the ignition key.
Back Door Lock Assembly Back Door Courtesy Light Switch Detects whether the back door is open or closed and sends this information to the main body ECU (multiplex network body ECU).
Door Lock Motor Drives the motor in response to signals from the main body ECU (multiplex network body ECU) and releases the back door latch.
Back Door Opener Switch Assembly Sends back door opener switch signals to the certification ECU (smart key ECU assembly).
Power Window Regulator Master Switch Assembly Door Lock Switch Sends manual lock and unlock request signals to the main body ECU (multiplex network body ECU).
Certification ECU (Smart Key ECU Assembly) Sends the back door opener switch signals to the main body ECU (multiplex network body ECU).
Combination Meter Assembly Receives signals from the speed sensor and sends the vehicle speed signal to the main body ECU (multiplex network body ECU).
Main Body ECU (Multiplex Network Body ECU) Drives all door lock motors in response to signals.



FUNCTION


a.

The power door lock control system has the following functions:

Function Outline

*1: Destination package for Korea

Manual Lock and Unlock This function can lock or unlock all doors by operation of the door lock switch.
Manual Unlock Prohibition Performing the door lock operation with a door control transmitter will prohibit the doors from being unlocked by the door lock control switch.
Key-linked Lock and Unlock This function, linked with the driver door key cylinder, can lock or unlock all the doors when a lock or unlock operation is effected.
Key-linked Unlock (2-step Unlock)*1, *2 When the mechanical key in electrical key transmitter sub-assembly is inserted into the door lock cylinder and is turned once, the driver door is unlocked. Then, when the key is turned again, all doors are unlocked.
Key Confinement Prevention When the electrical key transmitter sub-assembly is present in the interior detection area and a door lock operation is performed while the driver door is open, all the doors will be unlocked.
Shift-linked Automatic Door Lock*1, *2 When the conditions listed below are met consecutively, this function causes all the doors to be automatically locked.
·

The power switch is changed from off or on (ACC) to on (IG).

·

All doors are closed.

·

With the shift lever in P, the shift lever is moved to any position other than P.

·

Any one of the doors is in an unlocked state.


Speed-sensitive Automatic Door Lock*1, *2, *3 When the conditions listed below are met, this function causes all the doors to be automatically locked.
·

Vehicle speed is higher than approximately 20 km/h (12 mph).

·

All doors are closed.

·

Any one of the doors is in an unlocked state.


Shift-linked Automatic Door Unlock*1, *2 When the power switch is on (IG), and the shift lever is in P, all the doors will be automatically unlocked.
Driver Door Opening-linked Automatic Door Unlock*1, *2, *3 All doors are automatically unlocked when the driver door is opened within 43 seconds after the power switch is changed from on (IG) to on (ACC) or off.
Back Door Open Pressing the back door opener switch when the back door is unlocked will open the back door.

HINT:

*2: Customizable parameters can be configured by means of the customized body electronics system. For details, refer to the Repair Manual.

*3: Default setting off.