FUNCTION OF MAIN COMPONENTS
LED Headlight System
| Component | Function | |
|---|---|---|
| Main Body ECU (Multiplex Network Body ECU) | The main body ECU (multiplex network body ECU) receives the HEAD position signal from the light control switch and transmits a signal to the H-LP relay and DIM relay. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | The light control switch transmits a HEAD position signal to the main body ECU (multiplex network body ECU). |
| H-LP Relay | The H-LP relay supplies power to the LED driver modules (Light Control ECU). | |
| DIM Relay | The DIM relay sends a high beam signal to the LED driver modules (Light Control ECU). | |
| Headlight Assembly | Light Emitting Diode (LED) | The Light Emitting Diode (LED) light shines ahead over a broader area and further forward, increasing the area visible to the driver. |
| LED Driver Module (Light Control ECU) | The LED driver module (Light Control ECU) keeps a constant level of direct current applied to the LED, achieving stable LED illumination. | |
| Combination Meter Assembly | Taillight Indicator Light | The taillight indicator lights up to inform the driver when the taillights turn on. |
| High Beam Indicator Light | The high beam indicator lights up to inform the driver when the high beam headlights turn on. | |
| Master Warning Light | The master warning light illuminates to inform the driver when the LED driver module detects malfunctions in this system. | |
| Multi-information Display | The multi-information display displays a warning message to inform the driver when the LED driver module (light control ECU) detects a malfunction in this system. | |
Daytime Running Light System
| Component | Function | |
|---|---|---|
| Main Body ECU (Multiplex Network Body ECU) | Receives various signals and illuminates the daytime running lights. | |
| DRL Relay | Supplies power to the daytime running lights. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | Outputs a light control switch position signal to the main body ECU (multiplex network body ECU). |
| Parking Brake Switch Assembly | Outputs a parking brake signal to the main body ECU (multiplex network body ECU). | |
| Hybrid Vehicle Control ECU | Outputs a READY signal to the main body ECU (multiplex network body ECU). | |
Automatic Headlight Beam Level Control System
| Component | Function | |
|---|---|---|
| Headlight Leveling ECU Assembly | ·
The headlight leveling ECU assembly detects changes of vehicle movement based on the rear height control sensor RH and vehicle speed signal. ·
The headlight leveling ECU assembly outputs control signals to the headlight leveling motors based on the detected value. ·
This ECU provides initial set control and a fail-safe function. |
|
| Headlight Assembly | Headlight Leveling Motor | ·
Based on the signals received from headlight leveling ECU assembly, each headlight leveling motor moves the projector unit in the headlight to vary its angle. ·
Each headlight leveling motor uses a stepper motor to precisely regulate the angle of the projector unit. |
| Main Body ECU (Multiplex Network Body ECU) | The main body ECU (multiplex network body ECU) receives a HEAD position signal from the light control switch and transmits it to the headlight leveling ECU assembly. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | The light control switch transmits a HEAD position signal to the main body ECU (multiplex network body ECU). |
| Rear Height Control Sensor Sub-assembly RH | The rear height control sensor sub-assembly RH detects vehicle movement and transmits a signal to the headlight leveling ECU assembly. | |
| Combination Meter Assembly | The combination meter assembly transmits a vehicle speed signal to the headlight leveling ECU assembly. | |
| Combination Meter Assembly | Master Warning Light | The master warning light illuminates to inform the driver when the headlight leveling ECU assembly detects malfunctions in this system. |
| Multi-information Display | The multi-information display displays a warning message to inform the driver when the headlight leveling ECU assembly detects a malfunction in this system. | |
Manual Headlight Beam Level Control System
| Component | Function |
|---|---|
| Headlight Leveling Switch | The level of the headlight can be adjusted between 0 and 4.5, and a switch level status signal is sent to the headlight leveling motor. |
| Headlight Leveling Motor | Headlight leveling motors in accordance with signals from the headlight leveling switch and moves the reflector up and down. |
Automatic Light Control System
| Component | Function | |
|---|---|---|
| Main Body ECU (Multiplex Network Body ECU) | Receives various signals and illuminates the headlights, taillights, clearance lights and license plate lights. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | Outputs a light control signal and transmits it to the main body ECU (multiplex network body ECU). |
| Automatic Light Control Sensor | Detects the ambient light level and transmits the light level signals to the main body ECU (multiplex network body ECU). | |
| Front Door Courtesy Light Switch Assembly (Driver Side) | Detects whether a door is open or closed and transmits a signal to the main body ECU (multiplex network body ECU). | |
Light Reminder System
| Component | Function |
|---|---|
| Main Body ECU (Multiplex Network Body ECU) | Outputs taillight illumination signals and driver's door open signals to the combination meter assembly. |
| Front Door Courtesy Light Switch Assembly (Driver Side) | Detects whether driver's door is open or closed and transmits a signal to the main body ECU (multiplex network body ECU). |
| Combination Meter Assembly | Receives taillight illumination signals and driver's door open signals from the main body ECU (multiplex network body ECU) when the power switch is turned off and sounds the buzzer. |
Light Auto Turn-Off System
| Component | Function | |
|---|---|---|
|
*1: Models with front fog light *2: Models with rear fog light |
||
| Main Body ECU (Multiplex Network Body ECU) | Receives various signals, and turns off the exterior lights. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | The light control switch transmits a light control position signal to the main body ECU (multiplex network body ECU). |
| Front Door Courtesy Light Switch Assembly (LH, RH) | Detects whether a door is open or closed and transmits a signal to the main body ECU (multiplex network body ECU). | |
| Rear Door Courtesy Light Switch Assembly (LH, RH) | ||
| Back Door Lock Assembly | Back Door Courtesy Light Switch | |
| H-LP Relay | Shuts down power to the low beams. | |
| FOG FF Relay* | Shuts down power to the fog lights. | |
| FOG RR Relay* | ||
| TAIL Relay | Shuts down power to the taillights, clearance lights, and license plate lights. | |
Emergency Brake Signal
| Component | Function | |
|---|---|---|
| Brake Actuator Assembly | Skid Control ECU | Receives various signals and transmits an emergency brake signal to the combination meter assembly. |
| Speed Sensor | Detect the wheel speed of each of the 4 wheels. | |
| Airbag Sensor Assembly | Outputs the acceleration information. | |
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | |
| Combination Meter Assembly | Receives the emergency brake signal and controls the hazard warning lights. | |
SYSTEM CONTROL
LED Headlight System
When the light control switch is turned on, the LED driver module (light control ECU) immediately turn on the LEDs (approximately 0.1 sec). In addition, by regulating the output currents flowing into the LEDs at the specified level, the LED driver module (light control ECU) prevent the glare of light due to voltage variation.
If malfunctions occur in the LED headlight system, an LED driver module (light control ECU) transmits fail signals to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives fail signals, it transmits signals to the combination meter, warning the driver.
Daytime Running Light System
The daytime running lights illuminate when the following conditions are met.
The power switch is turned on (IG).
The parking brake is off.
The headlight dimmer switch assembly is in the AUTO position (and the taillights are not turned on via the automatic light control system).
Automatic Headlight Beam Level Control System
The rear height control sensor sub-assembly RH detects a change in height of the rear shaft in response to the weight applied to the rear of the vehicle when the vehicle is stopped and sends the change amount signal to the headlight leveling ECU. The headlight leveling ECU calculates the vehicle posture based on the change amount and controls the headlight beam level by operating the headlight leveling motor.
Light Auto Turn-Off System
The light auto turn-off system operates as follows:
| Condition | Details |
|---|---|
|
*: Models with Automatic Light Control System |
|
| Auto Turn-off | When all of the following conditions are met, the exterior lights automatically turn off:
·
The power switch is turned off. ·
The driver door is opened. ·
The headlight dimmer switch assembly (light control switch) is in the AUTO position*, TAIL position or HEAD position. |
| Exterior Light Auto Cut | If the exterior lights illuminate for 20 minutes or more with the power switch off, the system automatically turns the exterior lights off. |
Emergency Brake Signal
The activating and deactivating conditions for the emergency brake signal are as shown in the following table:
| Condition | Details |
|---|---|
| Emergency Brake Signal Operating Conditions | When all of the following conditions are met, the emergency brake signal starts operating:
·
Vehicle speed is above 55 km/h (35 mph). ·
Driver is depressing the brake pedal. ·
Emergency braking is detected from the vehicle deceleration. |
| Emergency Brake Signal Ending Conditions | When any of the following conditions is met, the emergency brake signal stops operating:
·
Driver has released the brake pedal. ·
Emergency braking is no longer detected from the vehicle deceleration. ·
Driver has pressed the hazard warning signal switch. |
FUNCTION
Automatic Headlight Beam Level Control System
The automatic headlight beam level control system mainly consists of the headlight leveling ECU assembly, rear height control sensor sub-assembly RH and 2 headlight leveling motors. The headlight leveling ECU assembly controls the system.
The ECU detects the movement of the suspension from the rear height control sensor sub-assembly RH and the vehicle speed from the combination meter sub-assembly.
The ECU then controls the headlight leveling motor based on this information, in order to change the headlight reflector angle.
When the headlight leveling ECU assembly detects that the vehicle is stopped and the power switch is on (IG), the ECU executes the initial setting of the stepper motors.
Manual Headlight Beam Level Control System
The manual headlight beam level control system keeps the beam of the headlight adjusted to the appropriate level in accordance with the number (weight) of passengers and volume of luggage.
The headlight beam level can be adjusted from 0 to 4.5 by operating the headlight leveling switch.
| *1 | Headlight Leveling Switch | - | - |
Light Reminder System
The light reminder system warns the driver using a buzzer when the meter ECU inside the combination meter assembly receives the driver's door courtesy light switch signal via the main body ECU (multiplex network body ECU) and the power switch is turned off and the door is opened with the taillights kept on. The buzzer is located inside the combination meter assembly.
| Light Control Switch Position | Power Switch | Door | Buzzer |
|---|---|---|---|
| TAIL, HEAD | Switch off | Open | Sounds |
| Closed | - |
CONSTRUCTION
LED Headlight System
LED headlight system is newly employed for the headlights. The high and low beams are switched using a projector unit shade for efficient use of the light source.
| *1 | Headlight Assembly
·
High/Low Beam |
*2 | LED |
| *3 | Projector Unit Shade | *4 | Solenoid |
| *a | When in Low Beam | *b | When in High Beam |
LED Driver Module
The LED driver modules are placed beneath the headlights and this supplies a constant voltage to the low beams and reduces the changes in the energization current.
FAIL-SAFE
LED Headlight System
The LED driver module (light control ECU) executes the fail-safe actions listed below in accordance with the problem that has been detected.
| Problem | Outline |
|---|---|
| Abnormal Output (Open Circuit or Short Circuit) | If an abnormal condition (open or short) occurs in the voltage that is output by the LED driver module (light control ECU), the LED driver module (light control ECU) stops illuminating the headlights and will maintain this state until the power is reinstated. Power is reinstated by turning the headlight dimmer switch assembly (light control switch) from off to on. |
| Abnormal input voltage (High input voltage) | When the headlights are on, if the LED driver module (light control ECU) receives a voltage of more than 17 V, it will turn the headlights off. When the input voltage resumes to the normal operating voltage range, the LED driver module will turn the headlights on. |
| Abnormal input voltage (Low input voltage) | When the headlights are on, if the LED driver module (light control ECU) detects that the input voltage has decreased to 6 to 10 V, it will dim the headlights. When the input voltage resumes to a normal operating voltage range, the LED driver module will return the headlight brightness to the normal brightness. |
| If the LED driver module receives a voltage of less than 6 V, it will turn the headlights off. When the power voltage resumes to more than 8.5 V, the LED driver module will turn the headlights on. |
Automatic Headlight Beam Level Control System
If an abnormal condition such as those listed below has been detected, the headlight leveling ECU operates in the fail-safe mode.
| Problem | Outline |
|---|---|
| Power Supply Voltage Malfunction | Holds the beam at the position of the headlight leveling motor when the abnormality has been detected. |
| Rear Height Control Sensor Sub-assembly Data Error During Initialization | |
| Vehicle Model Code Inconsistent | |
| Rear Height Control Sensor Sub-assembly Power Supply Malfunction | |
| Rear Height Control Sensor Sub-assembly Signal Malfunction |
DIAGNOSIS
LED Headlight System
If the main body ECU (multiplex network body ECU) detects a malfunction in the LED headlight system, the combination meter assembly flashes the master warning light and indicates the warning message on the multi-information display. At the same time, the Diagnostic Trouble Code (DTC) is stored in memory. The DTC can be read using the Global TechStream (GTS). For details, refer to the Repair Manual.
Automatic Headlight Beam Level Control System
When the headlight leveling ECU assembly detects malfunctions in the automatic headlight beam level control system, DTCs are stored in memory.
The DTCs can be read using the Global TechStream (GTS). For details, refer to the Repair Manual.