Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2017.06
NM2170E _59 Vehicle Exterior _056992 WINDOW / GLASS _0277792 POWER WINDOW CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


SYSTEM CONTROL


a.

The power window control system has the following system control:

Function Outline
Manual Up-and-down This function causes the window to close or open while driver side's switch of the power window regulator master switch assembly is being pulled halfway up or pushed halfway down, or while except driver side's switch of the power window regulator master switch or the power window regulator switch assembly is being pulled up or pushed down. The window stops as soon as the switch is released.
One-touch Auto Up-and-Down (Driver's Door) The one-touch auto up-and-down function enables the window to be fully closed or opened at a touch of the power window regulator master switch assembly.
Jam Protection (Driver's Door) The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the window during one-touch auto up operation or manual up operation.
Catch Protection (Driver's Door) Catch protection function automatically stops the power window if a foreign object gets jammed in the window during one-touch auto-down operation or power down.
Soft Stop (Driver's Door) During an up operation of the power window, the power window ECU stops the current to the power window motor right before the door glass is fully closed.
Remote Control The up-and-down operations of the front passenger's door window and the rear door windows can be controlled by operating the power window regulator master switch assembly.
Window Lock Power window operation of the front passenger's door window and the rear door windows is disabled when the window lock switch is pressed.
Key-off Operation The key-off operation function makes it possible to operate the power windows for approximately 43 seconds after the ignition switch is turned to ACC or off, if the front doors are not opened.

HINT:

The power window ECU built into the driver's door power window regulator motor assembly stores the initial position of its door window. The initial position is not cleared even if battery terminals, fuses or the power window motor connector is disconnected. However, after removing or reinstalling window components, or replacing the power window regulator sub-assembly or power window regulator motor assembly, the stored initial position data must be cleared and/or initialization must be performed. For details, refer to the Repair Manual.



b.

Jam Protection Function

i.

The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the door window during one-touch auto up operation or power up operation.


ii.

The operation of the jam protection function is described below.

Door Window Position from Full Close Operation
200 mm (7.87 in.) or more Down operation until door window downward movement of 125 mm (4.93 in.) is reached, or 2.5 seconds elapses.
200 mm (7.87 in.) or less Down operation until door window downward movement of 200 mm (7.87 in.) is reached, or 5 seconds elapses.



c.

Catch Protection Function

i.

The catch protection function automatically stops the power window if a foreign object gets caught in the window during a down operation.


ii.

The power window ECU determines if a foreign object gets caught according to changes in the output signal from the pulse sensor (Hall IC). The judgment method is as follows:



d.

Soft Stop Function

i.

During an up operation of the power window, the soft stop function stops the current to the power window motor right before the door glass is fully closed. This reduces the load on the door glass outer weatherstrip.


ii.

The power window ECU determines if the door glass stop position is detected according to changes in the output signal from the pulse sensor (Hall IC). The judgment method is as follows:

Judgment Method (Rotation Speed Comparison)
Y146731E01
2.552,0.698 2.552,0.385 2.552,0.385 2.781,0.385 false 4.594,1.833 4.24,1.833 4.24,1.833 4.24,1.583 false 0.49,0.969 1.833,1.427 1.344,0.458 10 false Power Window Motor Rotation Speed 2.833,0.292 4.448,0.667 1.615,0.375 10 false Change of Rotation Speed 4.469,1.063 5.656,1.438 1.188,0.375 10 false Threshold Value 4.646,1.74 6.26,2.115 1.615,0.375 10 false Judged Soft Stop 2.677,2.26 4.292,2.635 1.615,0.375 10 false Number of Pulse Edges




CONSTRUCTION


a.

The power window regulator motor assembly consists of a power window motor and a power window ECU.


b.

The power window ECU contains a built-in pulse sensor (Hall IC). The power window ECU detects the rotation of the power window motor according to output signals from the pulse sensor (Hall IC).

Y207592C01
4.104,0.708 4.75,0.333 4.75,0.333 4.917,0.333 true 4.833,1.25 5.479,0.875 5.479,0.875 5.646,0.875 true 4.99,0.24 5.302,0.438 0.313,0.198 10 false *2 5.698,0.76 6.01,0.958 0.313,0.198 10 false *1
*1 Power Window Motor *2 Power Window ECU



c.

Pulse Sensor (Hall IC)

i.

The pulse sensor (Hall IC) sends pulse signals (2 pulse signals with different phases) in sync with the motor rotation to the power window ECU.

Y207593C01
2.583,0.667 3,0.333 3,0.333 3.167,0.333 true 2.292,1.26 3,0.833 3,0.833 3.167,0.833 true 2.333,1.49 3,1.99 3,1.99 3.167,1.99 true 1.448,1.573 2.583,2.583 2.583,2.583 2.75,2.583 true 5.958,1.094 6.25,0.833 6.25,0.833 6.417,0.833 true 4.917,2.417 5.083,2.417 5.083,2.417 5.417,2.083 true 3.229,0.24 3.542,0.438 0.313,0.198 10 false *1 3.25,0.719 3.563,0.917 0.313,0.198 10 false *2 3.208,1.906 3.521,2.104 0.313,0.198 10 false *3 2.802,2.469 3.115,2.667 0.313,0.198 10 false *4 6.479,0.75 6.792,0.948 0.313,0.198 10 false *3 4.729,2.333 5.042,2.531 0.313,0.198 10 false *2 5.104,0.865 5.417,1.063 0.313,0.198 10 false S 5.667,0.885 5.979,1.083 0.313,0.198 10 false N 5.656,1.438 5.969,1.635 0.313,0.198 10 false S 5.073,1.438 5.385,1.635 0.313,0.198 10 false N
*1 Power Window ECU *2 Pulse Sensor (Hall IC)
*3 Magnet *4 Worm Shaft



ii.

The power window ECU detects the amount of door glass movement by counting pulse signal 1 sent from the pulse sensor (Hall IC). The power window ECU also detects the direction of the door glass movement using 2 types of signals: pulse signal 1 and pulse signal 2 which have different phases. The power window ECU controls each function according to the data about the door glass position obtained from the 2 pulse signals.

Y146732E02
0.083,0.344 1.448,0.802 1.365,0.458 10 false Door Glass Movement Amount Detection 0.083,2.302 1.448,2.76 1.365,0.458 10 false Door Glass Movement Direction Detection 1.688,0.448 2.656,0.74 0.969,0.292 10 false Pulse Signal 1 1.688,2 2.656,2.292 0.969,0.292 10 false Pulse Signal 1 1.688,2.792 2.656,3.083 0.969,0.292 10 false Pulse Signal 2 2.792,0.635 3.76,0.927 0.969,0.292 10 false LO 2.792,0.25 3.76,0.542 0.969,0.292 10 false HI 2.792,1.844 3.76,2.135 0.969,0.292 10 false HI 2.792,2.635 3.76,2.927 0.969,0.292 10 false HI 2.792,2.219 3.76,2.51 0.969,0.292 10 false LO 2.792,3.021 3.76,3.313 0.969,0.292 10 false LO 5.094,1.833 5.656,2.125 0.563,0.292 10 false HI 5.094,2.219 5.656,2.51 0.563,0.292 10 false LO 5.094,2.635 5.656,2.927 0.563,0.292 10 false HI 5.094,3.021 5.656,3.313 0.563,0.292 10 false LO 3.229,3.292 4.427,3.625 1.198,0.333 10 false Door Glass Down 5.615,3.292 6.813,3.625 1.198,0.333 10 false Door Glass Up 3.396,0.927 5.198,1.219 1.802,0.292 10 false Time for 1 Motor Revolution


iii.

The power window ECU detects changes in the motor rotation speed using pulse signal 1. As a result, the power window ECU detects the load applied to the door glass and controls the jam protection, catch protection and soft stop functions.

Y146733E02
0.333,1.688 1.708,2.156 1.375,0.469 10 false Door Glass Movement Speed Detection 2.042,0.813 3.417,1.281 1.375,0.469 10 false Pulse Signal 1 2.042,2.406 3.417,2.875 1.375,0.469 10 false Pulse Signal 1 3.104,1.031 3.583,1.406 0.479,0.375 10 false LO 3.104,0.656 3.583,1.031 0.479,0.375 10 false HI 3.104,2.25 3.583,2.625 0.479,0.375 10 false HI 3.104,2.625 3.583,3 0.479,0.375 10 false LO 3.625,1.51 4.167,1.865 0.542,0.354 10 false Normal 4.417,3.104 4.958,3.458 0.542,0.354 10 false Jammed




FAIL-SAFE


a.

When the power window ECU detects that there is an abnormality in the Hall IC which detects the position, speed and direction of the window, the ECU enters fail-safe mode.