OUTLINE
The 1NZ-FXE engine is an in-line, 4-cylinder, 1.5-liter, 16-valve DOHC engine.
This engine uses a high-expansion ratio Atkinson cycle, Variable Valve Timing-intelligent (VVT-i) system, Direct Ignition System (DIS), Electronic Throttle Control System-intelligent (ETCS-i) and Exhaust Gas Recirculation (EGR) system employing a highly efficient EGR cooler. In addition, use of an electric water pump has enhanced warm-up performance and reduced cooling losses. Thus, improved engine performance, quietness, fuel economy and cleaner emissions have been achieved.
SPECIFICATION
| Item | Specification | |||
|---|---|---|---|---|
| Engine Type | 1NZ-FXE | |||
| No. of Cyls. and Arrangement | 4-cylinder, In-line | |||
| Valve Mechanism | 16-valve DOHC, Chain Drive (with VVT-i) | |||
| Combustion Chamber | Pentroof Type | |||
| Flow of Intake and Exhaust Gasses | Cross-flow | |||
| Fuel System | SFI | |||
| Ignition System | DIS | |||
| Displacement | 1497 cm3 (91.3 cu. in.) | |||
| Bore x Stroke | 75.0 mm x 84.7 mm (2.95 in. x 3.33 in.) | |||
| Compression Ratio | 13.4:1 | |||
| Max. Output (SAE-NET)*1 | 54 kW @ 4800 rpm | |||
| Max. Torque (SAE-NET)*1 | 111 N*m @ 3600 to 4400 rpm | |||
| Valve Timing | Intake | Open | 25°BTDC to 22°ATDC | |
| Close | 55°ABDC to 102°ABDC | |||
| Exhaust | Open | 34° BBDC | ||
| Close | 2° ATDC | |||
| Oil Grade | API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving", SN PLUS "Resource-Conserving" or ILSAC multigrade engine oil | |||
| Firing Order | 1 - 3 - 4 - 2 | |||
| Research Octane Number (RON) | 91 or higher | |||
| Emission Regulation*2 | EURO 5, EURO 5+, EURO 6 | |||
| Emission Regulation*3 | Regulation | CARB*4 | EPA*5 | |
| Tailpipe | LEV3-SULEV30 | Tier3-Bin30 | ||
| Evaporative | LEV2 Near-zero Evaporative, ORVR | Tier2, ORVR | ||
| Engine Service Mass*6 (Reference) | 81.9 kg (181 lb.) | |||
*1: Maximum output and torque rating is determined by revised SAE J1349 standard.
*2: Emission regulations differ by country and region.
*3: Destination package models for Korea
*4: California Air Resources Board (CARB)
*5: Environmental Protection Agency (EPA)
*6: The figure shown is the weight of the engine without coolant and oil.
MAIN FEATURES
The 1NZ-FXE engine has achieved the following performance through the use of the items listed in the table below.
(1) High performance and reliability
(2) Low noise and vibration
(3) Lightweight and compact design
(4) Good serviceability
(5) Clean emissions and fuel economy
| Item | (1) | (2) | (3) | (4) | (5) | |
|---|---|---|---|---|---|---|
| The high-expansion ratio Atkinson cycle is adopted. | - | - | - | - | ○ | |
| Engine Control System | The Electronic Throttle Control System-intelligent (ETCS-i) is used. | ○ | - | - | - | ○ |
| The non-contact sensor is used in the throttle position sensor. | ○ | - | - | - | - | |
| A flat type knock control sensor is used. | ○ | - | - | - | - | |
| Engine Proper | An aluminum cylinder block sub-assembly is used. | - | - | ○ | - | - |
| An offset crankshaft is used. | ○ | ○ | - | - | ○ | |
| The taper squish shape is used for the top of the pistons. | ○ | - | - | - | ○ | |
| The skirt portion of the piston has a resin coating applied to reduce friction. | ○ | - | - | - | ○ | |
| Low-tension piston rings are used. | ○ | - | - | - | ○ | |
| Valve Mechanism | A chain sub-assembly and No. 1 chain tensioner assembly are used. | - | ○ | - | ○ | - |
| The Variable Valve Timing-intelligent (VVT-i) system is used. | ○ | - | - | - | ○ | |
| Fuel System | 12-hole type fuel injector assemblies are used. | ○ | - | - | - | ○ |
| A fuel delivery pipe made of pressed steel is used. | ○ | - | ○ | - | - | |
| A fuel returnless system is used. | - | - | ○ | ○ | - | |
| Quick connectors are used to connect the fuel hoses and fuel pipes. | - | - | - | ○ | - | |
| Intake and Exhaust System | A plastic intake manifold is used. | - | - | ○ | - | - |
| A linkless type throttle with motor body assembly is used. | - | - | ○ | ○ | - | |
| A step motor type Exhaust Gas Recirculation (EGR) valve assembly is used. | - | - | - | - | ○ | |
| A water-cooled type EGR cooler assembly is used. | ○ | - | - | - | ○ | |
| A stainless steel exhaust manifold is used. | - | - | ○ | - | - | |
| A rearward exhaust layout is used. | - | - | - | - | ○ | |
| Three-Way Catalytic converters (TWCs) are used. | - | - | - | - | ○ | |
| A 2-way exhaust control system is used. | ○ | ○ | - | - | - | |
| Cooling System | An electric engine water pump assembly is used. | ○ | - | ○ | ○ | ○ |
| Ignition System | A Direct Ignition System (DIS) is used. | ○ | - | - | ○ | ○ |
○: Applicable
-: Not applicable