Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2019.07
NM2170E _58 Vehicle Interior _056987 METER / GAUGE / DISPLAY _0277786 METER / GAUGE SYSTEM UN GENERAL/CONTROL/DETAILS F

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


OPERATING CONDITION


a.

Hybrid System Indicator Operation Condition

i.

Hybrid System Indicator is activated when the following conditions are met.

Condition
·

The power switch turned on (IG).

·

READY ON state.

·

The shift position is in D or B.






SYSTEM CONTROL


a.

Seat Belt Warning

i.

When the power switch is on (IG), this system detects the condition of the seat belts based on the signals from the front seat belt buckle switch (driver and front passenger) and the weight detector sensor*1 or occupant classification sensors*2.

*1: Except destination package for Korea

*2: Destination package for Korea


ii.

The seat belt warning light located in the combination meter assembly is used for both the driver and front passenger seats.


iii.

After the power switch is turned on (IG), if the driver or front passenger has not fastened their seat belt, the seat belt warning light will begin flashing.


iv.

When the seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will start sounding intermittently. At this time, the seat belt warning light flashing will change in sync with the intermittent buzzer sound. These buzzer and indicator warnings will continue for approximately 24 seconds until the seat belt is fastened.


v.

If the seat belt still remains unfastened over the approximately 30 seconds, the intervals of the intermittent buzzer sound and flashing light will change, and such warnings will continue for approximately 90 seconds until the seat belt is fastened.

Y212798E01
0.198,0.5 1.615,0.917 1.417,0.417 10 false Front Seat Belt Buckle Switch (Driver) 0.219,1.667 1.635,2.083 1.417,0.417 10 false Front Seat Belt Buckle Switch (Passenger)*1 0.208,2.667 1.667,3.083 1.458,0.417 10 false Occupant Classification ECU*1 0.198,3.656 1.656,4.073 1.458,0.417 10 false Occupant Classification Sensor*1 0.208,5.135 1.25,5.635 1.042,0.5 10 false Weight Detector Sensor*2 2.625,4.979 4.042,5.396 1.417,0.417 10 false Front Seat Belt Buckle Switch (Passenger)*2 2.719,4.125 4.135,4.542 1.417,0.417 10 false Skid Control ECU 2.625,3.521 4.292,3.938 1.667,0.417 10 false Brake Booster with Master Cylinder Assembly 2.646,2.667 4.479,3.083 1.833,0.417 10 false Airbag Sensor Assembly*1 2.635,1.688 4.49,2.063 1.854,0.375 10 false Hybrid Vehicle Control ECU 2.635,0.323 4.302,0.74 1.667,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 5.521,0.313 6.75,0.729 1.229,0.417 10 false Combination Meter Assembly 5.604,1.469 6.771,1.885 1.167,0.417 10 false Seat Belt Warning Light 5.604,2.833 7.021,3.25 1.417,0.417 10 false Buzzer 4.333,6.333 6.583,6.5 2.25,0.167 10 false : CAN Communication Line 0.167,6.031 2.917,6.365 2.75,0.333 10 false *1: Destination Package for Korea 0.167,6.406 3,6.656 2.833,0.25 10 false *2: Except Destination Package for Korea


vi.

While the seat belt warning light and buzzer are operating, fastening the seat belt will bring them to a stop.




FUNCTION


a.

Combination Meter

i.

The table below shows the combination meter function:

Y212799E01
1.885,1.24 1.417,0.667 1.417,0.667 1.25,0.667 true 2.344,1.198 2.5,0.667 2.5,0.667 2.667,0.667 true 2.833,1.104 3.219,0.646 3.219,0.646 3.385,0.646 true 4.083,1.083 4.26,0.635 4.26,0.635 4.427,0.635 true 5.208,1.094 5.385,0.646 5.385,0.646 5.552,0.646 true 1.021,0.573 1.229,0.844 0.208,0.271 10 false *1 2.719,0.583 2.927,0.854 0.208,0.271 10 false *2 3.438,0.563 3.646,0.833 0.208,0.271 10 false *3 4.5,0.552 4.708,0.823 0.208,0.271 10 false *4 5.604,0.573 5.813,0.844 0.208,0.271 10 false *3

Function Outline
*1 Speedometer Digitally displays the vehicle speed signal in MPH or km/h.
*2 Shift Position Indicator Displays the shift position.
*3 Indicator and Warning Lights Come on or blink to warn the driver.
*4 Multi-information Display Displays the vehicle's information, odometer, fuel gauge, clock and warning messages etc.
- Buzzers Sound to warn the driver.



b.

Multi-information Display

i.

The multi-information display consists of a constant display area and content display area.

Y212800C01
0.771,0.656 1,0.25 1,0.25 1.167,0.25 true 2.271,0.667 2.5,0.26 2.5,0.26 2.667,0.26 true 4.219,0.708 4.448,0.302 4.448,0.302 4.615,0.302 true 6.073,0.667 6.198,0.323 6.198,0.323 6.365,0.323 true 1.802,2.26 2.115,2.417 0.313,0.156 10 false *a 5.24,2.25 5.552,2.406 0.313,0.156 10 false *b 1.219,0.167 1.531,0.323 0.313,0.156 10 false *c 2.729,0.167 2.979,0.344 0.25,0.177 10 false *d 0.188,2.531 0.396,2.729 0.208,0.198 10 false *e 4.698,0.198 5.01,0.354 0.313,0.156 10 false *c 6.427,0.24 6.677,0.417 0.25,0.177 10 false *d
*a Standard Screen *b Simple Screen
*c Constant Display Area *d Content Display Area
*e The illustrations shown are examples only. The illustrations may differ from the actual vehicle screen. - -


Function Outline Display Area

*1: When Simple Screen is selected.

*2: When Trip Summary of Meter Settings is enabled.

Opening System activation animation will be displayed for approximately 3 seconds when the power switch is turned on (IG). All
Multi-information Drive Information, Eco Information and Settings can be selected. Content Display Area
Warning Message Warning messages interrupt the displayed information to warn the diver. Content Display Area
Clock Time is displayed. Constant Display Area / Content Display Area*1
ODO/TRIP Meter A travel distance is displayed in the odometer, trip meter A and trip meter B respectively. Constant Display Area
Average Fuel Consumption Average fuel consumption is calculated based on the distance the vehicle has run and the amount of fuel the vehicle has consumed, and then the calculation result is displayed. Constant Display Area
Ending System deactivation animation will be displayed for approximately 3 seconds when the power switch is turned off. All
Trip Summary*2 After the ending screen, pieces of information such as a travel distance, time and fuel consumption are displayed. Content Display Area


ii.

The multi-information display flow can be switched as shown in the flow chart below:

Y212736E02
3.479,0.229 3.792,0.427 0.313,0.198 10 false Off 2.885,0.938 4.406,1.167 1.521,0.229 10 false Power Switch On (IG) 2.875,1.948 4.01,2.167 1.135,0.219 10 false Opening Display 5.115,1.771 6.5,2.177 1.385,0.406 10 false Gasoline Price Setting Display 0.396,3.688 1.677,3.896 1.281,0.208 10 false Warning Display (3) 2.938,3.083 4.531,3.313 1.594,0.229 10 false Information Display (4) 2.5,3.521 4.615,3.771 2.115,0.25 10 false - Drive Information Tab 2.5,3.99 3.969,4.208 1.469,0.219 10 false - Eco Information Tab 2.5,4.448 3.781,4.656 1.281,0.208 10 false - Setting Tab 2.698,6.167 3.927,6.406 1.229,0.24 10 false Power Switch Off 5.354,6.177 6.604,6.406 1.25,0.229 10 false Diagnosis Display 3.458,7.042 3.771,7.24 0.313,0.198 10 false Off 0.281,6.156 1.667,6.417 1.385,0.26 10 false Warning Display (3) 3.677,6.656 4.135,6.854 0.458,0.198 10 false (5) 5.792,5.865 6.25,6.063 0.458,0.198 10 false (1) 6.313,5.813 6.771,6.01 0.458,0.198 10 false (2) 1.292,0.323 1.75,0.521 0.458,0.198 10 false (2) 0.865,0.083 1.323,0.281 0.458,0.198 10 false (1) 0.458,0.948 1.74,1.156 1.281,0.208 10 false Warning Display (3) 4.74,1.146 5.198,1.344 0.458,0.198 10 false (2) 4.729,2.5 5.188,2.698 0.458,0.198 10 false (1) 1.781,3.552 2.24,3.75 0.458,0.198 10 false (1) 1.885,4.042 2.344,4.24 0.458,0.198 10 false (2) 1.708,6.979 2.167,7.177 0.458,0.198 10 false (1) 2.229,6.104 2.688,6.302 0.458,0.198 10 false (2)

Number Transition Condition
(1) Conditions are met.
(2) Conditions are not met.
(3) If there are multiple display requests, items will be displayed in sequence.
(4) Item or display is selected by operating the steering pad switch assembly switch.
(5) After the power switch off, the Trip Summary is displayed for a fixed time. (When Trip Summary of Meter Settings is enabled.)


iii.

The information currently displayed can be switched using the LEFT/RIGHT switch on the steering pad switch assembly.

Y212801C01
4.917,1.083 5.083,1.083 5.083,1.083 5.406,1.365 true 5.719,1.375 6,1.75 6,1.75 6.167,1.75 true 4.281,0.646 4.531,0.917 0.25,0.271 10 false *1 4.667,0.948 4.979,1.104 0.313,0.156 10 false *a 6.24,1.677 6.469,1.844 0.229,0.167 10 false *b 0.146,3.885 0.406,4.052 0.26,0.167 10 false *c 2.635,3.896 2.948,4.052 0.313,0.156 10 false *d 5.125,3.896 5.438,4.052 0.313,0.156 10 false *e 0.229,6.563 0.49,6.729 0.26,0.167 10 false *f
*1 Steering Pad Switch Assembly - -
*a LEFT Switch *b RIGHT Switch
*c Drive Information Tab *d Eco Information Tab
*e Setting tab *f The illustrations shown are examples only. The illustrations may differ from the actual vehicle screen.
V100135

LEFT switch operation
V100136

RIGHT switch operation




c.

Drive Information Tab

i.

Drive information tab shows vehicle information such as drivable range, fuel consumption and energy monitor.


ii.

The drive information tab can be switched using the UP/DOWN switch on the steering pad switch assembly.

Y212802C01
4.917,0.917 5.083,0.917 5.083,0.917 5.552,1.208 true 5.563,1.531 5.833,1.917 5.833,1.917 6,1.917 true 4.323,0.656 4.573,0.885 0.25,0.229 10 false *1 4.719,0.833 5.031,0.99 0.313,0.156 10 false *a 6.063,1.854 6.313,2.094 0.25,0.24 10 false *b 0.146,3.896 0.458,4.052 0.313,0.156 10 false *c 2.646,3.906 2.958,4.063 0.313,0.156 10 false *d 5.146,3.896 5.458,4.052 0.313,0.156 10 false *e 0.229,6.573 0.479,6.792 0.25,0.219 10 false *f
*1 Steering Pad Switch Assembly - -
*a UP Switch *b DOWN Switch
*c Drive Information *d Energy Monitor
*e Simple Screen *f The illustrations shown are examples only. The illustrations may differ from the actual vehicle screen.
V100135

UP switch operation
V100136

DOWN switch operation



iii.

The table below shows the drive information tab function:

Display Mode Outline
Drive Information Shows the pieces of information listed below.
·

Average Speed

·

Elapsed Time

·

EV Drive Ratio

·

EV Traveling Distance

·

Cruising Range


Energy Monitor
·

Shows the energy flow in the form of an arrow.

-

Engine to Tire

-

Engine to Battery

-

Battery to Tire

-

Tire to Battery


·

Shows the State Of Charge (SOC) of the HV battery in 8 levels.


Simple Display Displays the Clock, Outside Temperature and Fuel Gauge in content display area of multi-information display.



d.

Eco Information Tab

i.

Eco information tab shows vehicle information such as eco score and eco savings*.

*: Models for Australia


ii.

The eco information tab can be switched using the UP/DOWN switch on the steering pad switch assembly.

Y212803C01
4.917,0.917 5.083,0.917 5.083,0.917 5.552,1.24 true 5.552,1.542 5.833,1.917 5.833,1.917 6,1.917 true 4.313,0.667 4.615,0.896 0.302,0.229 10 false *1 4.698,0.813 5.01,0.969 0.313,0.156 10 false *a 6.063,1.833 6.375,1.99 0.313,0.156 10 false *b 0.188,3.552 0.5,3.708 0.313,0.156 10 false *c 2.656,3.542 3.208,3.74 0.552,0.198 10 false *d (*A) 5.146,5.854 5.458,6.01 0.313,0.156 10 false *f 2.646,5.833 2.938,6.031 0.292,0.198 10 false *g 0.177,5.844 0.49,6 0.313,0.156 10 false *h 0.156,7.615 0.406,7.844 0.25,0.229 10 false *i 5.125,3.531 5.677,3.729 0.552,0.198 10 false *e (*A)
*A Models for Australia - -
*1 Steering Pad Switch Assembly - -
*a UP Switch *b DOWN Switch
*c ECO Score *d ECO Savings
*e ECO Savings Record *f Past Record (Monthly Average)
*g Past Record (Own Best) *h Fuel Consumption Record
*i The illustrations shown are examples only. The illustrations may differ from the actual vehicle screen. - -
V100135

UP switch operation
V100136

DOWN switch operation



iii.

The table below shows the eco information tab function:

Display Mode Outline

*: Models for Australia

ECO Score
·

ECO Score: For every driving cycle that is from a start to a stop, the respective driving conditions of Start, Cruise and Stop are put into calculation to evaluate them, scoring how much the driving control is eco-friendly. Values obtained in this mode do not link to values in ECO Savings mode.

·

Start: The driving operating conditions, when the vehicle begins to move, are shown in bar graph to indicate how much they are eco-friendly.

·

Cruise: The driving operating conditions, when the vehicle runs at constant speeds, are shown in bar graph to indicate how much they are eco-friendly.

·

Stop: The driving operating conditions, when the vehicle decreases to stop, are shown in bar graph to indicate how much they are eco-friendly.

·

Since Hybrid System Indicator is provided on the same display screen, the driver can see if their driving controls are appropriate to achieve eco-friendly drive further.

·

Scores will be affected by external circumstances such as road conditions or surrounding environment. However, driving conditions while the cruise control system is active or the shift lever is in N will not be scored.


ECO Savings*
·

Displays the estimated consumed fuel cost and reduced fuel cost compared to the target vehicle information set by the user.

·

The fuel price and target vehicle fuel efficiency value for eco savings calculation, can be changed via the eco savings of setting tab.

·

Displays eco savings from hybrid system start or TRIP A and TRIP B eco savings.

·

The eco savings from hybrid system start or TRIP A and TRIP B can be changed using the TRIP switch of steering pad switch.


ECO Savings Record*
·

The gasoline consumption cost for the current month, last month, 2 months ago, 3 months ago, and 1 year ago is shown in bar graph, and the monthly fuel consumption amounts are shown by quantity.

·

The difference of the gasoline consumption costs between the driver's vehicle and comparison vehicle for the current month, last month, 2 months ago, 3 months ago, and 1 year ago is shown in bar graph, and the monthly fuel consumption amounts are shown by quantity.

·

Display of the difference of the gasoline consumption is enabled when eco savings of setting tab is apply.


Past Record (Monthly Average)
·

The monthly average fuel consumption for the current month, last month, 2 months ago, 3 months ago, and 1 year ago, is displayed with bar graphs.

·

The monthly travel distances are also displayed.


Past Record (Own Best)
·

The average fuel consumption performances are ranked in the 1st, 2nd and 3rd among the records, and the respective fuel efficiency value, date and travel distance are also displayed.

·

In addition, when the current performance is within the top 100, the current rank is shown. If the performance is ranked outside the top 100, "Outside Ranking" is displayed.


Fuel Consumption Record
·

The average fuel consumption, at 5 minute intervals or 1 minute intervals, is calculated from the distance the vehicle has traveled for 5 minutes or 1 minute and the amount of fuel the vehicle has consumed for that travel distance, and the calculation result is expressed with bar graphs.

·

The current fuel consumption is calculated by the combination meter based on the distance driven and the volume of fuel consumed, and the calculation result is expressed with bar graphs.

·

When the "Fuel Consumption Record" screen is displayed, proceeds to the interval time (5 minutes/1 minute) selection screen when the enter switch of steering pad switch is pressed and held.





e.

Hybrid System Indicator

i.

Hybrid System Indicator will appear when ECO Score mode or ECO Savings mode* is selected in the eco information tab.

*: Models for Australia


ii.

Hybrid System Indicator displays the total of the HV battery and engine output as the hybrid system output.


iii.

The scale for Hybrid System Indicator consists of the 3 indicators (Charge, Eco, Power). The role of each indicator is as follows.

Y212804E01
2.5,0.615 2.958,0.813 0.458,0.198 10 false (c) 4.469,0.146 4.927,0.344 0.458,0.198 10 false (d) 3.979,0.958 4.438,1.156 0.458,0.198 10 false (b) 1.865,1.25 2.323,1.448 0.458,0.198 10 false (a)

Indicator Function
(a) Charge (CHG) This shows that energy regeneration is occurring.
(b) Eco This indicator is active while the vehicle is driven eco-friendly.
(c) Eco (Hybrid Eco) This indicator shows that the vehicle is driven in a manner that promotes frequent motor only operation. (Based on the driving conditions, the hybrid vehicle control ECU determines if the engine should be stopped to enhance fuel efficiency.)
(d) Power (PWR) This indicator is on while the drive power is exceeding the eco-friendly driving range (during full power driving etc.).



f.

Setting tab

i.

The items displayed on the multi-information display can be customized.


ii.

The items can be selected on the information setting screen.

Y212868C01
0.115,1.531 0.427,1.729 0.313,0.198 10 false *a
*a The illustrations shown are examples only. - -


Adjust Light (Except destination package for Korea)
Item Available Setting

*: Displayed when the taillights are turned on.

Display Brightness* Meter panel luminance when the taillights are on can be changed.

Meter Settings
Item Available Setting
EV Mode Indicator Light The EV Mode Indicator Light can be changed:
·

ON

·

OFF


ECO Savings
·

The gasoline price can be changed.

·

The fuel consumption of a comparison vehicle can be changed.


Time and date The clock and date of the combination meter can be adjusted.
Units The unit displayed on the multi-information display can be changed:
·

km/h

·

MPH


Language The language used on the multi-information display can be changed:
·

English

·

Spanish

·

Traditional Chinese


Pop-up Guidance The pop-up guidance can be changed:
·

ON

·

OFF


Trip Summary The Trip Summary can be changed:
·

ON

·

OFF


Initialization The set items can be initialized.

HINT:

The selectable items may differ depending on the model or region.




g.

Warning Message

i.

When a warning is necessary, the warning display interrupts the display in the multi-information display.


ii.

The master warning light may illuminate or blink and the buzzer in the combination meter assembly may sound depending on the item in the multi-information display.


iii.

When multiple warning conditions occur at the same time, the highest priority warning message is displayed first. After 2 seconds has elapsed, the next highest priority warning message will be shown. Unless the causes of warnings are removed, the respective warning messages continue.

Priority Warning Message Master Warning Light Buzzer

*1: Models with cruise control system

*2: Models with LED headlight system

*3: Models with vehicle proximity notification system

*4: Destination package for Korea

1 MAINTENANCE MODE - -
CERTIFICATION MODE - -
2 SHIFT TO P BEFORE EXITING VEHICLE. Blinks Sounds
3 AUTO POWER OFF TO CONSERVE BATTERY - -
4 SHIFT TO P POSITION Blinks Sounds
SHIFT IS IN N RELEASE ACCELERATOR BEFORE SHIFTING. Blinks Sounds
HYBRID BATTERY LOW. HYBRID SYSTEM STOPPED. SHIFT TO P AND RESTART. Blinks Sounds
5 HYBRID SYSTEM MALFUNCTION. STOP IN A SAFE PLACE. SEE OWNER'S MANUAL. Illuminates Sounds
HYBRID BATTERY LOW. SHIFT OUT OF N TO RECHARGE. Blinks Sounds
RELEASE PARKING BRAKE Blinks Sounds
KEY NOT DETECTED Blinks Sounds
RELEASE ACCELERATOR Blinks Sounds
6 CHARGING SYSTEM MALFUNCTION STOP IN A SAFE PLACE. SEE OWNER'S MANUAL. Illuminates Sounds
CHECK ENTRY & START SYSTEM Blinks Sounds
CHECK CRUISE CONTROL SYSTEM*1 Illuminates Sounds
ENGINE OIL PRESSURE LOW Illuminates Sounds
7 TURN POWER OFF Blinks Sounds
KEY DETECTED IN VEHICLE Blinks Sounds
TURN LIGHTS OFF Blinks Sounds
DEPRESS BRAKE PEDAL, TOUCH POWER SWITCH WITH KEY Blinks Sounds
DEPRESS BRAKE PEDAL AND PUSH POWER SWITCH TO START Blinks Sounds
SHIFT INTO P POSITION TO START Blinks Sounds
8 STEERING LOCK ACTIVE Blinks Sounds
SHIFT INTO P POSITION TO START Blinks Sounds
DRIVE-START CONTROL MALFUNCTION VISIT YOUR DEALER Illuminates Sounds
BRAKE OVERRIDE MALFUNCTION VISIT YOUR DEALER Illuminates Sounds
9 KEY BATTERY LOW Illuminates Sounds
HYBRID SYSTEM OVERHEATED. REDUCED OUTPUT POWER. Illuminates Sounds
HEADLIGHT SYSTEM MALFUNCTION VISIT YOUR DEALER*2 Illuminates Sounds
ACOUSTIC VEHICLE ALERTING SYSTEM MALFUNCTION VISIT YOUR DEALER*3 Illuminates Sounds
ACCELERATOR AND BRAKE PEDALS DEPRESSED SIMULTANEOUSLY Blinks -
10 MAINTENANCE REQUIRED FOR TRACTION BATTERY COOLING PARTS SEE OWNER'S MANUAL - -
TRC OFF - -
MAINTENANCE REQUIRED SOON*4 - -
MAINTENANCE REQUIRED*4 - -
RESETTING MAINTENANCE DATA*4 - -
RESETTING OF MAINTENANCE DATA INCOMPLETE*4 - -
POWER ON - -
EV MODE CURRENTLY NOT AVAILABLE - Sounds
EV MODE NOT AVAILABLE: WARMING UP - Sounds
EV MODE NOT AVAILABLE: LOW BATTERY - Sounds
EV MODE NOT AVAILABLE: EXCESSIVE SPEED - Sounds
EV MODE NOT AVAILABLE: EXCESSIVE ACCELERATION - Sounds
EV MODE DEACTIVATED - Sounds
EV MODE DEACTIVATED: LOW BATTERY - Sounds
EV MODE DEACTIVATED: EXCESSIVE SPEED - Sounds
EV MODE DEACTIVATED: EXCESSIVE ACCELERATION - Sounds
ACCELERATOR PEDAL IS DEPRESSED. - -



h.

Buzzer

i.

The table below shows the warning and reminder functions of the buzzer in the combination meter assembly:

Priority Item
1 READY
2 Seat Belt Warning (Level 2)
3 Seat Belt Warning (Level 1)
4 Brake System Warning
5 Brake Fluid Low Warning
6 Engine Oil Pressure Warning
7 EPS Warning
8 Engine Coolant Temperature Warning
9 Door Open Warning When Not in P Position
10 Smart Entry and Start System Warning (Intermittent)
11 Key Reminder
12 Brake Operation Active Check Indication
13 Brake System Temperature Rise Warning
14 Smart Entry and Start System Warning (Intermittent 2)
15 Smart Entry and Start System Warning (Once)
16 Low Fuel Indicator
17 Multi-information Display Warning
18 Accelerator Depression with Neutral (N) Selected
19 Hybrid System Warning (Intermittent)
20 HV Battery Low Warning
21 Hybrid System Warning (Once)
22 HV Battery Charge Request
23 Hybrid System Overheat Warning
24 P Position Request at Start
25 Immobiliser Certification Reminder
26 Parking Brake Engaged Warning
27 Door Open while Driving Warning
28 EV Drive Mode Reject Warning
29 Light Reminder
30 Turn Flasher Sound



i.

Maintenance Required Reminder (Destination Package for Korea)

i.

A maintenance required reminder will appear to remind the driver to have maintenance performed based on the vehicle driving distance.


ii.

The combination meter assembly calculates the vehicle driving distance based on signals from the skid control ECU.


iii.

There are 2 types of warnings: one is displayed when the vehicle driving distance is 9800 km or more since the last time the system was reset, and the other is displayed when the driving distance is 10000 km or more.


iv.

The maintenance required reminder method has the following equipment:

Reminder Method 9800 km or more 10000 km or more
Maintenance required reminder message on the multi-information display "MAINTENANCE REQUIRED SOON" appears for approximately 16 seconds. "MAINTENANCE REQUIRED" warning remains on.


v.

After maintenance, the accumulated vehicle travel distance memorized in the combination meter assembly should be reset to zero using the TRIP switch of the steering pad switch assembly.

HINT:

The accumulated vehicle travel distance can be reset using the following procedure.

·

Turn the power switch on (IG), and make sure that trip meter A is displayed.

·

Turn the power switch off. While pushing the TRIP switch of the steering pad switch assembly, turn the power switch on (IG).

·

With the power switch on (IG), continue holding the TRIP switch of the steering pad switch assembly (for at least 5 seconds) with the trip meter A counting down. Release the TRIP switch of the steering pad switch assembly when the resetting procedure has completed.

·

When resetting is completes, the trip meter A will display "000000".





j.

Light Control Rheostat (Destination Package for Korea)

i.

The brightness of the instrument panel can be adjusted when the taillights are turned on.


ii.

The nighttime brightness level of the combination meter assembly can be adjusted between 1% and 12.5% for the daytime brightness level of 100%, by using a dial-type switch, and the indicator lights on the combination meter assembly can be turned off by further decreasing the brightness level.

Y212784C01
0.771,0.313 1.083,0.469 0.313,0.156 10 false *1
*1 Light Control Rheostat - -