Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2015.11
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM(w/o Canister Pump Module) J

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the power switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the power switch is turned on (IG), the MIL should be illuminated and should turn off after power switch on (READY). If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A275618E07
1.438,3.719 1.74,3.875 0.302,0.156 10 false G77 2.365,3.115 2.583,3.333 0.219,0.219 10 false 9 1.688,1.469 1.927,1.625 0.24,0.156 10 false IG2 1.438,3.875 2.979,4.333 1.542,0.458 10 false Certification ECU (Smart Key ECU Assembly) 0.396,2.375 0.75,2.521 0.354,0.146 10 false P/I 0.521,3.604 1.083,4.01 0.563,0.406 10 false Auxiliary Battery 1.271,2.177 3.052,2.448 1.781,0.271 10 false No. 1 Integration Relay 1.938,3.208 2.323,3.365 0.385,0.156 10 false IG2D 0.229,1.958 0.427,2.115 0.198,0.156 10 false 2E 0.344,1.781 0.438,1.938 0.094,0.156 10 false 1 1.021,1.958 1.219,2.115 0.198,0.156 10 false 2D 1.135,1.781 1.229,1.938 0.094,0.156 10 false 2 2.948,0.792 3.146,0.948 0.198,0.156 10 false 2D 2.99,0.615 3.083,0.771 0.094,0.156 10 false 4 2.802,1.958 3,2.115 0.198,0.156 10 false 2D 2.906,1.781 3.021,1.938 0.115,0.156 10 false 3 3.583,0.958 4.146,1.115 0.563,0.156 10 false METER 4.156,0.688 4.344,0.844 0.188,0.156 10 false 21 4.417,0.927 4.677,1.083 0.26,0.156 10 false IG+ 5.313,0.688 5.49,0.844 0.177,0.156 10 false 24 5,0.938 5.313,1.094 0.313,0.156 10 false EFI 6.51,3.729 6.833,3.885 0.323,0.156 10 false ECM 6.156,3.729 6.427,3.885 0.271,0.156 10 false A40 0.396,2.948 0.771,3.094 0.375,0.146 10 false MAIN 4.26,1.292 4.563,1.448 0.302,0.156 10 false G1 4.26,1.458 5.49,1.833 1.229,0.375 10 false Combination Meter Assembly 5.865,0.688 6.042,0.844 0.177,0.156 10 false 27 6.125,0.688 6.302,0.844 0.177,0.156 10 false W 0.781,0.948 1.021,1.104 0.24,0.156 10 false IG2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result
Result Proceed to
MIL remains on A
MIL does not illuminate B



A

2.CHECK WHETHER DTC OUTPUT RECURS

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Check if any DTCs have been detected. Note down any DTCs.

Result
Result Proceed to
DTC is not detected A
Any DTCs are detected B

HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
U158930E03
0.708,0.042 0.875,0.219 0.167,0.177 10 false *a 0.604,1.104 0.865,1.281 0.26,0.177 10 false A40

Disconnect the A40 ECM connector.


b.

Turn the power switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-24 (EFI) or A40-27 (W) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the power switch is turned on (IG).

OK:

MIL should be illuminated.




OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start* B

HINT:

*: The tester cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-24 (EFI) - A40-27 (W) Always Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR