Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM D

1NZ-FXE ENGINE CONTROL  SFI SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

HINT:

If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.



A317524E18
0.375,1.135 2.063,1.333 1.688,0.198 10 false 0.5 seconds 1.302,1.135 2.99,1.333 1.688,0.198 10 false 0.5 seconds 2.26,1.135 3.427,1.375 1.167,0.24 10 false 0.5 seconds 2.448,0.25 3.25,0.563 0.802,0.313 10 false DTC stored 0.396,2.792 3.271,3.063 2.875,0.271 10 false Freeze frame data which can be read

The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data can be checked.

-

3 data sets before the DTC was stored.

-

1 data set when the DTC was stored.

-

1 data set after the DTC was stored.


These data sets can be used to simulate the condition of the vehicle around the time of the occurrence the malfunction. The data may assist in identifying the cause of the malfunction, and judging whether it was temporary or not.




PENDING FREEZE FRAME DATA


HINT:

Pending freeze frame data is stored when a 2 trip DTC is first detected during the first trip.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Select a DTC in order to display its pending freeze frame data.

HINT:
·

Pending freeze frame data is cleared when any of the following occurs.

-

Using the tester, the DTCs cleared.


-

The cable is disconnected from the negative (-) auxiliary battery terminal.


-

40 trips with the engine fully warmed up have been performed after returning to normal. (Pending freeze frame data will not be cleared by only returning the system to normal.)


·

With previous pending freeze frame data stored, if pending freeze frame data is newly stored when a 2 trip DTC is detected in the first trip, the old freeze frame data will be replaced with the new one of the newly detected DTC in the next trip.



A251781E01
0.157,0.105 6.892,0.596 6.734,0.491 10 When a DTC is detected in both the first and second trips but the system returns to normal from the third trip (2 trip logic DTC): 0.161,1.627 1.073,1.808 0.912,0.181 10 Power Switch 1.3,1.46 2.112,1.751 0.812,0.291 10 On (IG) 1.3,1.847 1.553,2.021 0.253,0.174 10 Off 0.153,2.58 1.190,2.895 1.038,0.316 10 Pending Freeze Frame Data 1.336,2.496 1.786,2.691 0.449,0.196 10 Stored 1.322,2.783 1.829,3.109 0.507,0.326 10 Not Stored 0.121,3.709 1.128,4.437 1.007,0.729 10 Freeze Frame Data 1.294,3.665 1.744,3.861 0.449,0.196 10 Stored 0.363,4.695 1.748,4.900 1.385,0.205 10 :Malfunction detected 0.363,5.003 2.081,5.208 1.718,0.205 10 :Malfunction not detected 2.072,0.884 2.763,1.089 0.691,0.205 10 (First Trip) 2.822,0.884 3.783,1.124 0.961,0.239 10 (Second Trip) 3.781,0.884 4.743,1.124 0.961,0.239 10 (Third Trip) 4.594,0.891 5.555,1.131 0.961,0.239 10 (Fourth Trip) 1.301,3.939 1.808,4.265 0.507,0.326 10 Not Stored

A251782E02
0.188,0.175 7.059,0.590 6.871,0.415 10 When 2 trip DTC is first detected in the first trip and another 2 trip DTC is first detected in the second trip: 0.601,1.529 1.514,1.840 0.913,0.311 10 Power Switch 1.778,1.361 2.295,1.581 0.517,0.221 10 On (IG) 1.778,1.72 2.126,1.897 0.348,0.177 10 Off 0.48,2.327 1.538,2.692 1.059,0.364 10 Pending Freeze Frame Data A 0.48,3.276 1.538,3.640 1.059,0.364 10 Pending Freeze Frame Data B 1.778,2.25 2.232,2.418 0.455,0.167 10 Stored 1.778,3.154 2.232,3.322 0.455,0.167 10 Stored 1.778,2.533 2.232,2.930 0.455,0.397 10 Not Stored 1.778,3.444 2.232,3.840 0.455,0.397 10 Not Stored 0.676,4.107 3.188,4.351 2.512,0.244 10 :Pending malfunction A detected 0.676,4.574 3.188,4.818 2.512,0.244 10 :Pending malfunction B detected 0.676,5.045 2.767,5.271 2.091,0.225 10 :No malfunction detected 4.197,2.874 5.302,3.053 1.105,0.179 10 Uploaded 2.637,0.716 3.335,1.025 0.698,0.309 10 (First Trip) 3.538,0.716 4.676,0.983 1.137,0.267 10 (Second Trip) 4.608,0.716 5.736,1.048 1.128,0.332 10 (Third Trip) 5.523,0.716 6.716,1.053 1.193,0.336 10 (Fourth Trip)



LIST OF FREEZE FRAME DATA


Refer to "Data List / Active Test" (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DATA LIST / ACTIVE TEST).