Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2015.11
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM(w/o Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P060A  Internal Control Module Monitoring Processor Performance  


MONITOR DESCRIPTION

The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU monitors the communications and WDC pulses from the sub CPU. When the signal malfunctions below are detected, the DTC is stored.

DTC No. DTC Detection Condition Trouble Area
P060A A CPU reset is performed after one of the following conditions is met (1 trip detection logic):
·

There is an ECM main CPU error.

·

There is an ECM sub CPU error.

·

There is an electronic throttle monitoring CPU error.


ECM

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the tester off.

5.

Turn the power switch off.

6.

Disconnect the tester.

7.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

8.

Connect the cable to the negative (-) auxiliary battery terminal.

9.

Connect the tester to the DLC3.

10.

Turn the power switch on (IG) and turn the tester on.

11.

Wait 16 seconds or more.

12.

Enter the following menus: Powertrain / Engine and ECT / DTC.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P060A.

16.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P060A)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.



e.

Turn the power switch off and turn the tester off.


f.

Disconnect the tester.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.


h.

Connect the cable to the negative (-) auxiliary battery terminal.


i.

Connect the tester to the DLC3.


j.

Turn the power switch on (IG).


k.

Turn the tester on.


l.

Wait 16 seconds or more.


m.

Enter the following menus: Powertrain / Engine and ECT / DTC.


n.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P060A is output B



A

B