Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › CAMSHAFT POSITION SENSOR
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277915 CAMSHAFT POSITION SENSOR A

1NZ-FXE ENGINE CONTROL  CAMSHAFT POSITION SENSOR  INSTALLATION  


PROCEDURE

Hide 11101E 1.INSTALL CAM POSITION SENSOR

a.
A412346C01
1.802,0.958 1.927,0.427 1.927,0.427 2.177,0.427 false 1.99,1.219 2.146,1.865 2.146,1.865 2.458,1.865 true 2.667,1.208 2.969,1.208 false 2.219,0.354 2.531,0.51 0.313,0.156 10 false *a 3,1.125 3.313,1.281 0.313,0.156 10 false *b 2.51,1.792 2.823,1.948 0.313,0.156 10 false A
*a O-ring Groove
*b Cam Position Sensor Tip


Clean the O-ring groove of the cam position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.



b.

Apply protective tape around the part (A) shown in the illustration.


c.

Install a new O-ring to the cam position sensor.

NOTICE:

Set the O-ring on the tip of the cam position sensor and roll it into the O-ring groove with bare hands to install it.



d.
A407852C01
0.906,1.344 1.031,1.49 1.031,1.49 1.25,1.49 false 2.219,3.156 2.219,2.865 false 2.521,0.49 2.688,0.26 2.688,0.26 2.896,0.26 false 2.521,1.354 2.688,1.479 2.688,1.479 2.927,1.479 false 2.823,2.875 3.104,2.875 false 1.927,2.26 2.208,2.26 false 2.208,1.49 2.208,1.198 false 0.906,2.99 1.031,3.135 1.031,3.135 1.25,3.135 false 0.865,0.667 1.208,0.51 1.208,0.51 1.406,0.51 true 0.865,2.302 1.208,2.146 1.208,2.146 1.406,2.146 true 1.292,1.417 1.604,1.573 0.313,0.156 10 false *1 2.938,0.177 3.146,0.385 0.208,0.208 10 false *c 0.313,0.333 0.625,0.49 0.313,0.156 10 false *a 0.323,2 0.635,2.156 0.313,0.156 10 false *b 0.583,0.854 0.74,1.052 0.156,0.198 10 true A 1.031,0.854 1.188,1.052 0.156,0.198 10 true A 1.031,2.51 1.188,2.708 0.156,0.198 10 true B 0.604,2.51 0.76,2.708 0.156,0.198 10 true B 2.156,1.51 2.469,1.667 0.313,0.156 10 false *1 2.156,3.177 2.469,3.333 0.313,0.156 10 false *1 2.344,0.094 2.802,0.292 0.458,0.198 10 false A - A 2.354,1.875 2.813,2.073 0.458,0.198 10 false B - B 3.135,2.813 3.344,3.021 0.208,0.208 10 false *c 2.969,1.406 3.177,1.615 0.208,0.208 10 false *c 1.75,2.177 1.958,2.385 0.208,0.208 10 false *c 1.281,3.063 1.594,3.219 0.313,0.156 10 false *1 1.448,0.448 1.656,0.656 0.208,0.208 10 false *c 1.438,2.083 1.646,2.292 0.208,0.208 10 false *c
*1 O-ring
*a OK
*b NG
*c Seam


Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



e.

Remove the protective tape.

NOTICE:

Make sure to remove the protective tape and any tape adhesive residue.



f.
A412347C01
1.781,1.885 1.781,1.563 false 1.729,1.896 2.042,2.052 0.313,0.156 10 false *1
*1 O-ring


Apply a light coat of engine oil to the O-ring on the cam position sensor.


g.

Install the cam position sensor with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

If the cam position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or does not move out of place during installation.




h.

Connect the cam position sensor connector.


Hide 2.INSPECT FOR OIL LEAK