Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › IGNITION COIL AND SPARK PLUG › 2014.12–2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277917 IGNITION COIL AND SPARK PLUG A

1NZ-FXE ENGINE CONTROL  IGNITION COIL AND SPARK PLUG  INSTALLATION  


PROCEDURE

Hide 19100P 1.INSTALL SPARK PLUG

a.

Using a 16 mm spark plug wrench, install the 4 spark plugs.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

If a component has been dropped or subjected a strong impact, replace it.


HINT:

Perform "Inspection After Repairs" after replacing the spark plug (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).



Hide 19500F 2.INSTALL PLUG CAP

HINT:
·

Only perform this procedure when replacement of the plug cap is necessary.

·

If the plug cap has any damage, replace it with a new one.



a.
A326010E03
1.396,1.771 0.917,1.771 false 1.573,2.479 0.99,2.479 false 0.792,2.396 0.99,2.594 0.198,0.198 10 false *1 0.719,1.667 0.917,1.865 0.198,0.198 10 false *a

Clean the plug cap fitting of the No. 1 ignition coil.

Text in Illustration
*1 Plug Cap
*a Plug Cap Fitting

NOTICE:

Foreign matter adhering to the plug cap fitting can cause high-voltage electrical leakage.



b.

Install the plug cap to the No. 1 ignition coil.

A326011E03
0.938,1.083 0.646,1.49 0.646,1.49 0.448,1.49 true 0.854,1.76 0.979,2.313 0.979,2.313 1.177,2.313 true 2.302,1.135 2.01,1.542 2.01,1.542 1.823,1.542 true 2.719,0.979 2.958,1.844 2.958,1.844 3.094,1.844 true 4,1.052 3.708,1.469 3.708,1.469 3.521,1.469 true 4.198,0.99 4.469,1.531 4.469,1.531 4.646,1.531 true 5.802,1.208 6.073,1.75 6.073,1.75 6.25,1.75 true 0.417,0.115 0.74,0.385 0.323,0.271 10 false *a 2.021,0.094 2.344,0.365 0.323,0.271 10 false *b 3.615,0.104 3.938,0.375 0.323,0.271 10 false *b 1.646,0.313 1.969,0.583 0.323,0.271 10 false *c 0.281,1.417 0.604,1.688 0.323,0.271 10 false *d 1.208,2.219 1.531,2.49 0.323,0.271 10 false *e 1.688,1.469 2.01,1.74 0.323,0.271 10 false *f 3.146,1.76 3.469,2.031 0.323,0.271 10 false *g 3.365,1.385 3.688,1.656 0.323,0.271 10 false *h 4.677,1.448 5,1.719 0.323,0.271 10 false *i 6.281,1.667 6.604,1.938 0.323,0.271 10 false *d

Text in Illustration
*a Correct *b Incorrect
*c Section (A) *d Spring
*e Area with Talc Applied *f Inner Tube is Pinched
*g Inner Tube *h Inner Tube is Deformed
*i Spring is Pinched - -

NOTICE:
·

Make sure the plug cap is fully inserted all the way to section (A).

·

When installing the plug cap, do not allow any foreign matter to adhere to the plug cap or plug cap fitting.

·

When installing the plug cap, be careful not to damage the plug cap or plug cap fitting.

HINT:

Allowing any foreign matter to adhere to the contact surfaces, or damaging the plug cap or plug cap fitting, can result in high-voltage electrical leakage.


·

When installing the plug cap, make sure not to pinch the inner tube.

·

When installing the plug cap, make sure the spring is not pinched by the inner tube.

·

After installing the plug cap, look through the tip of the plug cap into the interior and check that the inner tube and spring are not pinched or deformed.

HINT:

If there is any pinching or deformation of the inner tube or spring, the electrical connection between the spring and spark plug terminal will be poor, which can result in engine misfires and DTC output.


·

When installing the plug cap, do not remove the talc (white powder) that has been applied to the inner surfaces of the plug cap.

HINT:

If the amount of talc applied is insufficient, this may cause the plug cap and spark plug to become stuck together in the future.


·

When installing the plug cap or spark plug, do not apply oil or grease to the engagement surfaces of the plug cap or spark plug.

HINT:

Applying any oil or grease can cause the plug cap to deteriorate, resulting in high-voltage electrical leakage.





Hide 19500D 3.INSTALL NO. 1 IGNITION COIL

a.
A268161E01
2.268,1.59 2.463,1.785 0.195,0.195 10 *2 2.268,0.696 2.463,0.891 0.195,0.195 10 *1

Install the 4 No. 1 ignition coils with the 4 bolts.

Text in Illustration
*a Body
*b Cap

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

If the body or cap of the No. 1 ignition coil is dropped or subjected to a strong impact, replace the No. 1 ignition coil with a new one.


HINT:

Perform "Inspection After Repairs" after replacing the ignition coil assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).



b.

Connect the 4 No. 1 ignition coil connectors.