Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  ECU Power Source Circuit  


DESCRIPTION

If the power switch is on (IG), the power management control ECU applies current to the MREL terminal to turn the IGCT relay on. This supplies power to the +B1 and +B2 terminals.

WIRING DIAGRAM

A263317E02
4.911,0.591 6.794,0.733 1.883,0.142 10 to Shift Lever Position Sensor 5.036,4.887 7.118,5.056 2.082,0.169 10 Power Management Control ECU 3.598,1.133 3.921,1.275 0.323,0.142 10 PCU 5.406,1.708 5.677,1.850 0.272,0.142 10 A39 5.498,1.512 5.593,1.678 0.095,0.167 10 5 5.498,3.725 5.593,3.892 0.095,0.167 10 5 5.498,4.153 5.593,4.319 0.095,0.167 10 5 5.498,1.928 5.593,2.095 0.095,0.167 10 2 5.498,2.363 5.593,2.529 0.095,0.167 10 6 5.498,2.843 5.593,3.009 0.095,0.167 10 6 5.777,1.708 6.059,1.850 0.282,0.142 10 +B1 5.777,2.128 6.059,2.270 0.282,0.142 10 +B2 5.777,3.032 5.976,3.174 0.199,0.142 10 E1 5.777,3.917 6.059,4.059 0.282,0.142 10 E01 5.777,4.345 6.059,4.487 0.282,0.142 10 E02 5.777,2.573 6.219,2.715 0.442,0.142 10 MREL 5.406,2.573 5.677,2.715 0.272,0.142 10 A39 5.406,3.032 5.703,3.174 0.297,0.142 10 G57 5.406,3.917 5.698,4.059 0.293,0.142 10 G57 5.406,4.345 5.706,4.487 0.301,0.142 10 G58 5.406,2.128 5.677,2.270 0.272,0.142 10 A38 3.374,1.726 4.132,1.868 0.758,0.142 10 IGCT NO. 3 3.374,2.263 4.132,2.405 0.758,0.142 10 IGCT NO. 2 2.195,2.966 2.550,3.108 0.355,0.142 10 IGCT 0.673,2.391 1.454,2.533 0.781,0.142 10 IGCT-MAIN 0.389,2.227 0.485,2.369 0.096,0.142 10 2 0.389,2.563 0.485,2.705 0.096,0.142 10 1 3.948,2.04 4.043,2.182 0.096,0.142 10 2 3.499,2.04 3.595,2.182 0.096,0.142 10 1 1.895,2.468 1.991,2.610 0.096,0.142 10 2 2.764,2.468 2.860,2.610 0.096,0.142 10 1 1.895,2.04 1.991,2.182 0.096,0.142 10 3 2.764,2.04 2.860,2.182 0.096,0.142 10 5 0.673,3.068 1.060,3.210 0.388,0.142 10 MAIN 0.794,3.874 1.834,4.016 1.040,0.142 10 Auxiliary Battery

PROCEDURE

1.CHECK POWER MANAGEMENT CONTROL ECU (+B1, +B2 VOLTAGE)
a.

Turn the power switch on (IG).


b.
U181223E03
0.677,2.656 0.938,1.708 false 1.521,2.667 1.323,1.708 false 0.698,0.979 0.969,1.146 0.271,0.167 10 false A38 1.281,0.979 1.552,1.146 0.271,0.167 10 false A39 1.375,2.667 1.667,2.823 0.292,0.156 10 false +B1 0.479,2.667 0.771,2.844 0.292,0.177 10 false +B2 0.188,0.125 0.365,0.302 0.177,0.177 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-5 (+B1) - Body ground Power switch on (IG) 11 to 14 V
A38-2 (+B2) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


c.

Turn the power switch off.



OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

3.CHECK POWER MANAGEMENT CONTROL ECU (MREL VOLTAGE)
2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
a.

Disconnect connector G57 and G58 from the power management control ECU.


b.
U158925E02
1.781,2.115 1.479,2.896 false 1.854,2.115 1.927,2.906 false 2.708,2.115 2.531,2.906 false 1.385,2.906 1.604,3.073 0.219,0.167 10 false E1 2.396,2.917 2.688,3.083 0.292,0.167 10 false E02 1.802,2.906 2.083,3.073 0.281,0.167 10 false E01 0.188,0.188 0.406,0.354 0.219,0.167 10 false *a 1.865,1.469 2.156,1.625 0.292,0.156 10 false G57 2.635,1.469 2.927,1.625 0.292,0.156 10 false G58

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G57-5 (E01) - Body ground Always Below 1 Ω
G57-6 (E1) - Body ground Always Below 1 Ω
G58-5 (E02) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


c.

Connect the power management control ECU connectors.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POWER MANAGEMENT CONTROL ECU (MREL VOLTAGE)
a.

Turn the power switch on (IG).


b.
U158922E02
1.25,1.708 1.083,2.448 false 0.271,0.25 0.438,0.406 0.167,0.156 10 false *a 0.854,2.458 1.26,2.615 0.406,0.156 10 false MREL 1.281,0.99 1.552,1.156 0.271,0.167 10 false A39

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-6 (MREL) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)



OK

4.CHECK FUSE (IGCT NO. 2)

NG

4.CHECK FUSE (IGCT NO. 2)
a.
A263634E01
0.252,0.383 0.403,0.529 0.151,0.147 10 *1 2.647,2.984 2.798,3.130 0.151,0.147 10 *2 2.484,2.158 2.727,2.964 false

Remove the IGCT NO. 2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 2 fuse terminals Always Below 1 Ω


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT NO. 2 Fuse


c.

Install the IGCT NO. 2 fuse.



OK

5.CHECK FUSE (IGCT-MAIN)

NG

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY)
5.CHECK FUSE (IGCT-MAIN)
a.
A264124E02
1.167,2.531 1.104,2.917 false 0.135,0.125 0.313,0.323 0.177,0.198 10 false *1 1.021,2.938 1.198,3.135 0.177,0.198 10 false *2

Remove the IGCT-MAIN fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT-MAIN fuse terminals Always Below 1 Ω


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT-MAIN Fuse


c.

Install the IGCT-MAIN fuse.



OK

6.INSPECT RELAY (IGCT)

NG

12.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY)
6.INSPECT RELAY (IGCT)
a.

Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.
A253297E01
0.165,0.068 0.398,0.266 0.232,0.198 10 *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage is applied between terminals 1 and 2 Below 1 Ω


Text in Illustration
*1 IGCT Relay


c.

Install the IGCT relay.



OK

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY)

NG

REPLACE RELAY (IGCT)

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY)
a.

Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect connector A38 and A39 from the power management control ECU.


c.

Measure the resistance according to the value(s) in the table below.

U183295E02
1.188,2.177 0.99,2.708 false 1.563,2.167 1.677,2.677 false 0.458,2.125 0.719,2.292 0.26,0.167 10 false A38 2.021,2.125 2.281,2.292 0.26,0.167 10 false A39 0.854,2.719 1.125,2.885 0.271,0.167 10 false +B2 1.563,2.698 1.844,2.865 0.281,0.167 10 false +B1 0.302,0.729 0.479,0.896 0.177,0.167 10 false *a 3.583,0.844 3.76,1.01 0.177,0.167 10 false *1 6.333,1.49 6.51,1.656 0.177,0.167 10 false *2

Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly *2 IGCT Relay
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
A39-5 (+B1) - 5 (IGCT relay) Always Below 1 Ω
A38-2 (+B2) - 5 (IGCT relay) Always Below 1 Ω



d.

Install the IGCT relay.


e.

Connect the power management control ECU connectors.



OK

8.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY)

NG

REPLACE FUSE (IGCT-MAIN)

8.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY)
a.

Remove the IGCT-MAIN fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


c.
A263631E01
0.224,0.183 0.398,0.342 0.174,0.158 10 *1 2.464,0.075 2.638,0.233 0.174,0.158 10 *2 0.625,2.802 0.799,2.960 0.174,0.158 10 *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay) - 2 (IGCT-MAIN fuse) Always Below 1 Ω


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT Relay
*3 IGCT-MAIN Fuse


d.

Install the IGCT-MAIN fuse.


e.

Install the IGCT relay.



OK

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY)
a.

Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect connector A39 from the power management control ECU.


c.

Measure the resistance according to the value(s) in the table below.

U158986E02
1.5,2.198 1.615,2.708 false 2.031,2.167 2.292,2.333 0.26,0.167 10 false A39 1.438,2.729 1.844,2.896 0.406,0.167 10 false MREL 0.323,0.771 0.5,0.938 0.177,0.167 10 false *a 3.594,0.885 3.771,1.052 0.177,0.167 10 false *1 6.333,1.5 6.51,1.667 0.177,0.167 10 false *2

Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly *2 IGCT Relay
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
A39-6 (MREL) - 1 (IGCT relay) Always Below 1 Ω
A39-6 (MREL) or 1 (IGCT relay) - Body ground and other terminals Always 10 kΩ or higher



d.

Install the IGCT relay.


e.

Connect the power management control ECU connectors.



OK

10.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.
A263633E01
0.307,0.54 0.459,0.686 0.152,0.145 10 *1 2.451,0.372 2.603,0.518 0.152,0.145 10 *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGCT relay) - Body ground Always Below 1 Ω


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT Relay


c.

Install the IGCT relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY)
a.

Disconnect connector C23 from the shift lever position sensor.


b.

Remove the IGCT NO. 2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


c.

Disconnect connectors A38 and A39 from the power management control ECU.


d.

Measure the resistance according to the value(s) in the table below.

U183298E02
1.188,2.177 0.99,2.708 false 1.563,2.167 1.677,2.677 false 0.448,2.125 0.708,2.292 0.26,0.167 10 false A38 2.021,2.125 2.281,2.292 0.26,0.167 10 false A39 0.854,2.719 1.125,2.885 0.271,0.167 10 false +B2 1.563,2.688 1.844,2.854 0.281,0.167 10 false +B1 0.302,0.729 0.479,0.896 0.177,0.167 10 false *a 3.927,0.885 4.104,1.052 0.177,0.167 10 false *1 5.51,2.833 5.688,3 0.177,0.167 10 false *2

Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly *2 IGCT NO. 2 Fuse
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
A39-5 (+B1) or 2 (IGCT NO. 2 fuse) - Body ground and other terminals Always 10 kΩ or higher
A38-2 (+B2) or 2 (IGCT NO. 2 fuse) - Body ground and other terminals Always 10 kΩ or higher



e.

Install the IGCT NO. 2 fuse.


f.

Connect the shift lever position sensor connector.


g.

Connect the power management control ECU connectors.



OK

REPLACE FUSE (IGCT NO. 2)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY)
a.
A263636E01
0.247,0.338 0.413,0.480 0.166,0.142 10 *1 0.93,2.968 1.096,3.110 0.166,0.142 10 *2 2.043,2.968 2.209,3.110 0.166,0.142 10 *4 2.532,2.968 2.699,3.110 0.166,0.142 10 *5 2.636,0.647 2.802,0.789 0.166,0.142 10 *3 1.17,2.524 1.022,2.948 false 2.494,2.091 2.734,0.837 false 2.411,2.325 2.137,2.948 false 2.489,2.452 2.608,2.948 false

Remove the IGCT-MAIN fuse, IGCT NO. 2 fuse, IGCT NO. 3 fuse and PCU fuse from the No. 2 engine room relay block and No. 2 junction block assembly.

Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT-MAIN Fuse
*3 IGCT NO. 2 Fuse
*4 PCU Fuse
*5 IGCT NO. 3 Fuse


b.

Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


c.
A263631E01
0.224,0.183 0.398,0.342 0.174,0.158 10 *1 2.464,0.075 2.638,0.233 0.174,0.158 10 *2 0.625,2.802 0.799,2.960 0.174,0.158 10 *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay) or 2 (IGCT-MAIN fuse) - Body ground and other terminals Always 10 kΩ or higher


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT Relay
*3 IGCT-MAIN Fuse


d.
A263637E01
0.195,0.196 0.360,0.355 0.165,0.158 10 *1 2.452,0.076 2.617,0.234 0.165,0.158 10 *2 1.577,2.793 1.742,2.951 0.165,0.158 10 *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT relay) or 2 (IGCT NO. 2 fuse) - Body ground and other terminals Always 10 kΩ or higher


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT Relay
*3 IGCT NO. 2 Fuse


e.

Install the IGCT-MAIN fuse, IGCT NO. 2 fuse, IGCT NO. 3 fuse and PCU fuse.


f.

Install the IGCT relay.



OK

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (IGCT NO. 2)

14.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (IGCT-MAIN)